Metadata Report for BODC Series Reference Number 695937

Metadata Summary

Data Description
Data Category Hydrography time series at depth
Instrument Type
NameCategories
Aanderaa RCM 7/8 Recording Current Meter  current meters
Instrument Mounting moored surface buoy
Originating Country United Kingdom
Originator Mr John Howarth
Originating Organization Proudman Oceanographic Laboratory (now National Oceanography Centre, Liverpool)
Processing Status banked
Project(s) Coastal Observatory
 

Data Identifiers

Originator's Identifier AS9959_00903
BODC Series Reference 695937
 

Time Co-ordinates(UT)
Start Time (yyyy-mm-dd hh:mm) 2004-09-08 12:45
End Time (yyyy-mm-dd hh:mm) 2004-10-29 12:15
Nominal Cycle Interval 600.0 seconds
 

Spatial Co-ordinates

Latitude 53.53550 N ( 53° 32.1' N )
Longitude 3.36717 W ( 3° 22.0' W )
Positional Uncertainty 0.0 to 0.01 n.miles
Minimum Sensor Depth 10.0 m
Maximum Sensor Depth 10.0 m
Minimum Sensor Height 12.0 m
Maximum Sensor Height 12.0 m
Sea Floor Depth 22.0 m
Sensor Distribution Fixed common depth - All sensors are grouped effectively at the same depth which is effectively fixed for the duration of the series
Sensor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
 

Parameters
BODC CODE Rank Units Title
AADYAA01 1 Days Date (time from 00:00 01/01/1760 to 00:00 UT on day)
AAFDZZ01 1 Days Time (time between 00:00 UT and timestamp)
ACYCAA01 1 Dimensionless Sequence number
CNDCPR01 1 Siemens per metre Electrical conductivity of the water body by in-situ conductivity cell
PSALPR01 1 Dimensionless Practical salinity of the water body by conductivity cell and computation using UNESCO 1983 algorithm
TEMPPR01 1 Degrees Celsius Temperature of the water body
 

Definition of Rank
  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

Temperature, conductivity and salinity

The temperature data recorded during this mooring deployment have been considered by BODC to be flawed. The values are constant for large portions of the record and do not match the temperature signal from other instruments deployed at the same mooring location at the same time. The data at the start and end of the record do not match the data from instruments deployed on previous or subsequent moorings at the same site.

As the temperature record is flawed, the conductivity and salinity data have been considered to be invalid also.

BODC therefore recommend that none of these data be used.

Data Access Policy

Public domain data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

The recommended acknowledgment is

"This study uses data from the data source/organisation/programme, provided by the British Oceanographic Data Centre and funded by the funding body."

Narrative Documents

Aanderaa Recording Current Meter Model 7/8

Manufacturer's specifications: recording unit height 49.5cm (RCM8 52.0cm), diameter 12.8cm, vane size 48.5x50.0cm. Meter is designed for depths down to 2000m (RCM8 6000m). It incorporates a spindle which is shackled to the mooring line. The meter is attached to the spindle through a gimbal mounting which permits a maximum 27° deviation of the spindle from the vertical, the meter still remaining horizontal.

Meter comprises :

  1. Paddle wheel rotor magnetically coupled to an electronic counter

  2. Vane, which aligns instrument with current flow, has a balance weight ensuring static balance and tail fins to ensure dynamic balance in flows up to 250cm/s.

  3. Magnetic compass (needle is clamped to potentiometer ring) - direction recorded with 0.35° resolution, 5° accuracy for speeds 5 to 100cm/s, 7.5° accuracy for remaining speeds within 2.5 to 200cm/s range.

  4. Quartz clock, accuracy better than 2 sec/day within temperature range 0 to 20°C.

  5. Thermistor (temperature sensor), standard range -2.46 to 21.48°C (max on high range 36.04°C), accuracy 0.05°C, resolution 0.1 per cent of range, 63 per cent response time 12sec.

  6. Inductive cell conductivity sensor (optional), range 0 to 70mmho/cm standard resolution 0.1 per cent of range.

  7. Silicon piezoresistive bridge, standard range 0 to 3000 psi (RCM8 to 9000 psi), resolution 0.1% of range.

  8. Self balancing potentiometer which converts the output from each sensor into a 10 bit binary number for storage on magnetic tape.

  9. Associated electronics.

A built-in clock triggers the instrument at preset intervals and up to six channels are sampled in sequence. Channel 1 is a fixed reference reading for control purposes and data identification. Channels 2, 3 and 4 represent measurement of temperature, conductivity and pressure. Channels 5 and 6 represent the VECTOR AVERAGED current speed and direction since the previous triggering of the instrument. The number of rotor revolutions and the direction is sampled every 12 seconds and broken into North and East components. Successive components are added and recorded as speed and direction. For recording intervals longer than 10 minutes, speed and direction are sampled 1/50th of recording interval.

It has become common practice in some laboratories to deploy these meters as temperature and conductivity loggers without current measuring capabilities.

The following link will provide the manufacturer specifications:

Manufacturer specifications

Originator processing for Irish Sea Observatory hydrographic data

The following procedures were carried out before the data were supplied to BODC.

Data were downloaded by the Proudman Oceanographic Laboratory (POL) [since 01 April 2010, the National Oceanography Centre Liverpool (NOC)] from the instrument logger, and factory calibrations were applied to the temperature and conductivity channels. The instruments are returned to the manufacturer for recalibration approximately every two years.

The data were then reformatted by POL/NOCL to a standard ASCII format for display on the Irish Sea Observatory website. The originator carried out limited quality control checks, which involved looking for obvious anomalies in the data , cross-checking against other datasets and timing checks. Any issues identified were fixed by POL staff, after which the data were made available on the website.

Processing undertaken by BODC: LB1_019/903 Aanderaa RCM7 #9959

The data (ASCII format) were acquired by BODC by download from the POL Irish Sea Observatory web site. They were reformatted to QXF format using BODC transfer function 318. The following table shows how the originator's variables were mapped to appropriate BODC parameter codes:

Originator's Variable Units Description BODC Parameter Code Units Comments
Temperature °C Temperature of the water column TEMPPR01 °C Data supplied as ITS-90
Conductivity S m-1 Electrical conductivity of the water column by in-situ conductivity cell CNDCPR01 S m-1 -
- - Practical salinity of the water column by conductivity cell and computation using UNESCO 1983 algorithm PSALPR01 - Derived during transfer from MATLAB Seawater Toolbox program 'sw_salt'. This uses UNESCO 1983 algorithm in Fofonoff and Millard (1983)

Salinity calculation

Salinity (PSS-78) was computed during transfer using the MATLAB sw_salt routine:

where

Quality control

The reformatted data were visualised using the in-house EDSERPLO software. Suspect and missing data were marked by adding appropriate quality control flags.

References

Fofonoff, N.P., and R.C. Millard Jr., 1983. "Algorithms for computation of fundamental properties of seawater", UNESCO technical paper in marine science 44, 53pp

General Data Screening carried out by BODC

BODC screen both the series header qualifying information and the parameter values in the data cycles themselves.

Header information is inspected for:

Documents are written by BODC highlighting irregularities which cannot be resolved.

Data cycles are inspected using time or depth series plots of all parameters. Currents are additionally inspected using vector scatter plots and time series plots of North and East velocity components. These presentations undergo intrinsic and extrinsic screening to detect infeasible values within the data cycles themselves and inconsistencies as seen when comparing characteristics of adjacent data sets displaced with respect to depth, position or time. Values suspected of being of non-oceanographic origin may be tagged with the BODC flag denoting suspect value; the data values will not be altered.

The following types of irregularity, each relying on visual detection in the plot, are amongst those which may be flagged as suspect:

If a large percentage of the data is affected by irregularities then a Problem Report will be written rather than flagging the individual suspect values. Problem Reports are also used to highlight irregularities seen in the graphical data presentations.

Inconsistencies between the characteristics of the data set and those of its neighbours are sought and, where necessary, documented. This covers inconsistencies such as the following:

This intrinsic and extrinsic screening of the parameter values seeks to confirm the qualifying information and the source laboratory's comments on the series. In screening and collating information, every care is taken to ensure that errors of BODC making are not introduced.

Project Information

Proudman Oceanographic Laboratory Coastal Observatory

The Coastal Observatory was established by Proudman Oceanographic Laboratory as a coastal zone real time observing and monitoring system. The main objective is to understand a coastal sea's response both to natural forcing and to the consequences of human activity. Near real-time measurements will be integrated with coupled models into a pre-operational coastal prediction system whose results will be displayed on the World Wide Web.

The Observatory is expected to grow and evolve as resources and technology allow, all the while building up long time series. A site selection pilot study was carried out in September 2001 and the Observatory became operational in August 2002.

The site is located in Liverpool Bay and is subject to typical coastal sea processes, with strong tides, occasional large storm surges and waves, freshwater input, stable and unstable stratification, high suspended sediment concentration and biogeochemical interaction. Measurements and monitoring will focus on the impacts of storms, variations in river discharge (especially the Mersey), seasonality and blooms in Liverpool Bay.

A variety of methods will be used to obtain measurements, including:

  1. Moored instruments for in situ time series of currents, temperature and salinity profiles, and surface waves and meteorology. It is hoped that turbidity and chlorophyll measurements will be made at another site as the Observatory progresses;
  2. The Cefas Smartbuoy for surface properties such as nutrients and chlorophyll, starting late 2002;
  3. R.V. Prince Madog to carry out spatial surveys and service moorings;
  4. Instrumented ferries for near surface temperature, salinity, turbidity, chlorophyll and nutrients. The first route will be Liverpool to Douglas, Isle of Man, starting late 2002;
  5. Drifters for surface currents and properties such as temperature and salinity, starting in 2004;
  6. Tide gauges, with sensors for meteorology, waves, temperature and salinity, where appropriate;
  7. Meteorological data from Bidston Observatory, HF radar and tide gauge sites;
  8. Shore-based HF radar measuring waves and surface currents out to a range of 50 km, starting in 2003;
  9. Satellite data, with infrared for sea surface temperature and visible for chlorophyll and suspended sediment.

The partners currently involved with the project are listed below:

A summary of Coastal Observatory cruises to date on R.V. Prince Madog is given in the table below:

Year No. of cruises Work summary
2001 1 Site selection and pilot study. 95 CTD casts.
2002 4 POL moorings deployed and serviced
Cefas Waverider and SmartBuoy deployed and serviced
103 CTD casts
2003 10 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
341 CTD/LISST casts
2004 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
347 CTD/LISST casts
2005 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
268 CTD/LISST casts
2006 11 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
508 CTD/LISST casts
2007 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
471 CTD/LISST casts
2008 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
260 CTD/LISST casts
2009 7 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
213 CTD/LISST casts
2010 8 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
268 CTD/LISST casts
2011 6 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
307 CTD/LISST casts to date, ongoing

Data Activity or Cruise Information

Data Activity

Start Date (yyyy-mm-dd) 2004-09-08
End Date (yyyy-mm-dd) 2004-10-29
Organization Undertaking ActivityProudman Oceanographic Laboratory (now National Oceanography Centre, Liverpool)
Country of OrganizationUnited Kingdom
Originator's Data Activity IdentifierLB1_019/POLRIG903
Platform Categorymoored surface buoy

Smartbuoy deployment LB1_019/POLRIG903

Deployment and Recovery

This rig was deployed as part of the Proudman Oceanographic Laboratory (POL) Liverpool Bay Coastal Observatory during R.V. Prince Madog cruise PD38_04. Recovery of the rig took place during R.V. Prince Madog cruise PD48_04. Further details are given below. Date and time are in Universal Time (UT) and are displayed in the ISO format YYYY-MM-DD hh:mm.

Rig Position (+ve N, + ve E) 53 32.13, -3 22.03
Water Depth (m) 22
Deployed 2004-09-08 12:42
Recovered 2004-10-29 12:20
No. of days 51

Rig Description

This rig is a single line mooring, comprising a surface Centre for Environment, Fisheries and Aquaculture Science (Cefas) SmartBuoy and POL instrumentation suspended beneath. The single point mooring was mainly composed of 0.5 inch long link chain and marked at the surface by a 1.8 m diameter toroid (the Cefas SmartBuoy) and anchored by a half tonne clump of scrap chain. The Smartbuoy contains a suite of instruments mounted just below the surface.

The table below details the Cefas instrumentation

Logging Unit Logged Instruments Serial
Number		 Parameters Meter
depth (m)
V2a Eco System Monitor UL017 Optical backscatter sensor 1679 Turbidity
Suspended load		 1
Falmouth Scientific OEM CT sensor 1841 Temperature
Salinity		 1
Chelsea Instruments Minitracka chlorophyll fluorometer 175067 Chlorophyll
Fluorescence		 1
Druck 5 bar pressure transducer 1245469 Pressure 1
LI-COR LI-192SB Underwater Quantum sensor 18 PAR
Vertical light attenuation coefficient		 2
LI-COR LI-192SB Underwater Quantum sensor 13 PAR
Vertical light attenuation coefficient		 1
V2a Eco System Monitor UL028 Seapoint Fluorometer 2245 Fluorescence
Chlorophyll		 1
Falmouth Scientific OEM CT sensor 1401 Temperature
Salinity		 1
Optical backscatter sensor 1550 Turbidity
Suspended load		 1
Druck 5 bar pressure transducer 1220412 Pressure 1
Stand-alone instrument EnviroTech WMS-2 Aqua Monitor water sampler 2326 Nitrite
Phosphate
Silicate
Total oxidised nitrogen
Suspended load		 1
Stand-alone instrument EnviroTech NAS-3X in situ nutrient analyser 2357 Total Oxidised Nitrogen 1
Stand-alone instrument EnviroTech WMS-1 Aqua Monitor water sampler 2384 Nitrite
Silicate
Suspended load
Total oxidised nitrogen		 1

The table below details the POL instrumentation

Instrument Serial Number Meter Level Parameters Measured Sampling Interval Comments
Sea-Bird MicroCAT SBE37-IM V2.1 2506 5 m below surface Temperature
Conductivity
Pressure		 10 minutes -
Aanderaa RCM7 without fin logging to Data Storage Unit (DSU) 8123 9959 10 m below surface Temperature
Conductivity
 10 minutes When recovered, clock was found to have been set one hour slow. NOC Liverpool technical staff corrected this offset before making data available.

Other Series linked to this Data Activity - 695949

Cruise

Cruise Name PD38/04
Departure Date 2004-09-08
Arrival Date 2004-09-09
Principal Scientist(s)M John Howarth (Proudman Oceanographic Laboratory)
Ship RV Prince Madog

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

Station NameCOA
CategoryOffshore area
Latitude53° 31.51' N
Longitude3° 23.00' W
Water depth below MSL26.0 m

Liverpool Bay Coastal Observatory Mooring Site A (COA/Site 1/Site 9)

This station is the main mooring site for the Proudman Oceanographic Laboratory (POL) Liverpool Bay Coastal Observatory and was first occupied in 2002. It is also known both as Coastal Observatory Site 1 and Site 9. POL perform two main types of activities at this station: they deploy moorings; and in addition, they take CTD profiles during each site visit. The station lies within a box of mean water depth 22.5 m with the following co-ordinates:

Box Corner Latitude (+ve North) Longitude (+ve East)
North-west corner 53.54097 -3.42958
South-east corner 53.50945 -3.33714

The position of this station relative to the other POL Coastal Observatory sites can be seen from the figure below.

BODC image

Mooring Deployment History

2011

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, OBS, OXY 1117 for January cruise. Other frame IDs not available at this time. January - September
SmartBuoy CTD x 2, AC-S, CT x 2, FL x 3, OBS x 2, PAR x 2, WMS, NAS, OXY, T x 2 1116 for January cruise. Other frame IDs not available at this time. January - September
SparBuoy AC-S, FL, CTD x 2, T Frame ID not available at this time. September

2010

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 1086, 1090, 1094, 1098, 1102, 1106, 1109 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T 1085, 1089, 1093, 1097, 1101, 1105, 1108, 1112 January - December

2009

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 1055, 1062, 1067, 1071, 1074, 1078, 1082 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T 1054, 1061, 1066, 1070, 1073, 1077, 1081 January - December

2008

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 1024, 1028, 1032, 1036, 1041, 1044, 1047, 1051 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T LB1_047/1023, LB1_048/1027, LB1_049/1031, LB1_050/1035, 1040, 1043, LB1_053/1050 January - December

2007

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 990, 997, 1001, 1005, 1010, 1014, 1017, 1021 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T LB1_039/989, LB1_040/996, LB1_041/1000, LB1_042/1004, LB1_043/1009, LB1_044/1013, LB1_045/1016, LB1_046/1020 January - December

2006

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 951, 962, 966, 970, 974, 978, 982, 986 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD 958, 961, 965, 969, 973, 977, LB1_037/981, LB1_038/985 January - December

2005

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CT 913, 914, 921, 925, 929, 933, 938, 942, 945, 949 January - December
SmartBuoy CT, FL, OBS, PAR, WMS, NAS, OXY 912, 920, 924, 928, 932, 937, LB1_028/941, LB1_029/944, LB1_030/948 January - December
Frame with telemetry buoy ADCP 914 March - April

2004

Rig Type Typical Instruments Rig IDs Comment
Frame BPR, ADCP, TR, CT 890, 892, 893, 896, 898, 900, 902, 904, 907, 908, 910, 911 January - December
SmartBuoy CT, FL, OBS, PAR, WMS, NAS 889, 891, 895, 897, 899, 901, 903, 906, 909 January - December
Frame with telemetry buoy ADCP 893, 908, 911 April - May, October - December

2003

Rig Type Instruments Rig IDs Comment
Frame BPR, ADCP, TR, CT 861, 864, 866, 869, 872, 878, 880, 883, 885, 887, 888 January - December
SmartBuoy CT, FL, OBS, PAR, WMS, NAS 863, 865, 867, 870, 871, 877, 879, 882, 884, 886 January - December

2002

Rig Type Instruments Rig IDs Comment
Frame BPR, ADCP, TR, CT 851, 854, 856, 858 August - December
Line mooring CT x 3 853, 855 August - November
SmartBuoy CT, FL, OBS, PAR, WMS, NAS 857, 860 November - December

2001

Rig Type Instruments Rig IDs Comment
Frame ADCP, OBS 838, 839, 840, 841, 843, 844, 845, 846, 848, 849 September

CTD Sampling History

Year Number of Cruises Total Casts per year
2011 6 116 including a 46 cast tidal cycle from 2011-04-18 to 2011-04-19 and a 51 cast tidal cycle station from 2011-07-27 to 2011-07-28
2010 7 69 including a 52 cast tidal cycle station from 2010-04-28 to 2010-04-29
2009 7 21
2008 9 75 including a 54 cast tidal cycle station from 2008-05-13 to 2008-05-14
2007 8 71 including a 51 cast tidal cycle station from 2007-05-15 to 2007-05-16
2006 9 72 including a 53 cast tidal cycle station from 2006-05-09 to 2006-05-10
2005 9 41 including a 22 cast tidal cycle station from 2005-04-05 to 2005-04-06
2004 9 77 including a 54 cast tidal cycle station from 2004-05-11 to 2004-05-12
2003 10 28
2002 4 13

The CTD instrument package for these cruises was a Sea-Bird 911plus, with beam transmissometer, fluorometer, LICOR PAR sensor, LISST-25, and oxygen sensor.

Key

AC-S = Absorption and attenuation spectrophotometer
ADCP = Acoustic Doppler Current Profiler
ADV = Acoustic Doppler Velocimeter
BD = Bacterial degradation experiment
BPR = Bottom Pressure Recorder
CT = Conductivity and temperature logger
CTD = Conductivity, temperature, depth sensor
FL = Fluorometer
NAS = in-situ nutrient analyser
OBS = Optical Backscatter Turbidity meter
OXY = Oxygen sensor
PAR = PAR sensor
T = Temperature logger
TR = Transmissometer
WMS = Automatic water sampler

Other Series linked to this Fixed Station for this cruise - 695949 695950 695974

Other Cruises linked to this Fixed Station (with the number of series) - PD01/08 (16) PD02/03 (4) PD02/05 (3) PD02/07 (14) PD02/09B (16) PD02/10 (9) PD05/10 (10) PD06/07 (15) PD07/08 (14) PD09/06 (11) PD09/07 (63) PD09/08 (15) PD10/03 (3) PD10/10 (8) PD11/05 (1) PD11/11 (48) PD12/05 (2) PD12/09 (10) PD13/07 (13) PD14/08 (67) PD16/06 (8) PD16/07 (14) PD17/03 (4) PD17/10 (9) PD18/04 (5) PD18/05 (3) PD18/09 (11) PD19/08 (2) PD20/02 (5) PD20/06 (8) PD20/07 (16) PD21/05 (3) PD21/10 (9) PD22/04 (5) PD22/06 (8) PD23/03A (4) PD23/07 (15) PD23/08 (12) PD24/02 (1) PD24/09 (11) PD25/03B (4) PD25/05 (3) PD25/06 (8) PD25/11 (4) PD27/07 (16) PD29/04 (4) PD29/06 (8) PD29/08 (13) PD29/10 (11) PD30/05 (2) PD31/02 (4) PD31/03 (4) PD32/04 (4) PD33/08 (4) PD33/09 (10) PD34/03 (4) PD34/05 (9) PD35/02 (4) PD35/06 (13) PD36/10 (10) PD37/06 (13) PD37/08 (17) PD38/03 (5) PD38/04 (3) PD38/09 (10) PD41/05 (10) PD43/11 (3) PD47/09 (9) PD48/05 (10) PD49/10 (7)

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference