Metadata Report for BODC Series Reference Number 862252

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."

Narrative Documents

Seapoint Chlorophyll Fluorometer

The Seapoint Chlorophyll Fluorometer (SCF) is a low power instrument for in situ measurements of chlorophyll a. The SCF uses modulated blue LED lamps and a blue excitation filter to excite chlorophyll a. The fluorescent light emitted by the chlorophyll a passes through a red emission filter and is detected by a silicon photodiode. The low level signal is then processed using synchronous demodulation circuitry which generates an output voltage proportional to chlorophyll a concentration. The SCF may be operated with or without a pump.

Sensor specifications, current at August 2006, are given in the table below. More information can be found at the manufacturer's web site.

Sensor Specifications

Cefas SmartBuoy data processing

This document outlines the procedures in place at Cefas in August 2005 for processing and quality assuring SmartBuoy data.

Raw data files are processed and the data move through 4 levels, starting with raw data at level 0 through to level 3, where data are fully quality-assured and expressed in appropriate units. The application of the procedures at each level result in data deemed fit to progress to the next level.

Cefas Quality Assurance (QA) Protocols

At Level 0, raw binary data files from the loggers are transferred to the network.

Automated checks - Level 1

Level 1 involves applying automated quality assurance procedures to the data. These include the following steps:

• Burst data are loaded into memory for processing.
• Calibration data for all instruments and sensors used on the deployment are retrieved from the SmartBuoy database. These may be manufacturers' sensor calibrations or the most current laboratory calibrations. Instruments are returned to the manufacturer and re-calibrated at regular intervals.
• mV are converted to volts, where necessary.
• LiCor signals are converted from Volts to PAR irradiance in µE m^-2 s^-1.
• Salinity is derived from C and T using UNESCO 88 (PSS78) formula.
• Burst data maximum and minimum ranges are checked and flagged if they fail the checks.
• Burst means, result count, and result standard deviation are calculated from non-flagged burst data.
• If there are data from two PAR sensors at different depths, Kd (m^-1) is calculated for burst mean data only as LN(PAR1m/PAR2m).
• Burst mean data maximum, minimum and rate of change checks are carried out and flags applied to any failures.
• Time stamped burst and burst mean data with default units are stored on SmartBuoy database.

The data are now at QA status = 1.

Manual checks - Level 2

Level 1 burst mean data are now ready for manual QA procedures in order to progress to Level 2. Deployment notes are consulted for any comments on sensor performance or malfunction and post-deployment photographs of sensors, if available, are examined.

Cefas use a data visualisation tool to examine the SmartBuoy data.

• A comparison is made between the end of one deployment with beginning of the next to identify possible drift and/or biofouling of OBS, Fluorometer, Salinity, PAR, and oxygen sensors.
• Battery voltages are checked for sudden jumps and, if present, other sensors are examined for similar jumps to determine whether there is a problem with the sensor or if the buoy was disturbed.
• Reference voltages on the FSI CT module are checked.
• The standard deviation of OBS is examined. A steady increase in standard deviation is a good indication of the onset of biofouling. It is also used as a rough indicator for fluorometers during summer, except during spring, when there are large fluctuations in chlorophyll.
• Li-Cor is examined for fouling, which could be indicated by a steady drop in daily maximum or a steady increase in standard deviation. If above-water Li-Cor data are available, they are used for comparison.
• Pressure is examined for sudden decreases, indicating when the buoy was taken out of the water.
• Roll and pitch are examined for any anomalies. It is expected that the spring/neap cycle will be present in the buoy tilt signal.
• Where possible, comparison is made between burst mean data from sensors measuring the same variable. This is in order to determine whether there is a systematic offset (drift) or sensor fault and whether biofouling is present.
• Comparison is made between burst mean sensor outputs from different variables as this can be helpful in determining the onset of biofouling. Any data that fail the checks are flagged with flags specific to the check that was failed.

Calibrations - Level 3

The combined information from Level 2 is used to determine the periods during which the data series are considered suspect. The data have now reached QA status = 2 and can progress to Level 3, where they will be fully calibrated with field-derived sample data.

• For salinity an offset is calculated as the difference between result output from logger and the result from a discrete sample collected at the same time.
• Calibration from regression analysis of field samples and logger output is applied to derive new parameters, e.g. chlorophyll calculated from fluorescence, suspended load calculated from OBS.
• Chlorophyll calibrations are determined from GF/F filtered water samples, which are extracted in acetone and measured for fluorescence using a Turner Designs Fluorometer.
• Suspended matter calibrations are determined from a known volume of water sample filtered through pre-weighed 0.4 µm Cyclopore filters. The filters are dried and reweighed to determine the weight of material per unit volume.
• Salinity is calibrated using water samples that have been analysed with a Guildline Autosal salinometer.
• Water samples from the Aqua Monitor are analysed for nutrients by colorimetric analysis of 0.4 µm Cyclopore-filtered samples.

The data have now reached QA status = 3 as time stamped, field calibrated burst mean data with parameter codes and units stored on SmartBuoy database with associated uncertainty or 95% confidence limits as appropriate. All SmartBuoy data banked at BODC have passed full Cefas QA procedures. Data that fail the Cefas QA checks are not submitted for banking.

SmartBuoy data processing by BODC

The following outlines the procedures that take place at BODC for banking Cefas SmartBuoy data.

BODC receives SmartBuoy data from Cefas after all quality checks have been passed and all possible calibrations applied. The data files are submitted as separate MS Excel spreadsheets for each parameter, i.e. there are separate files for temperature and salinity from the same instrument. An exact copy of the data is archived for safekeeping upon arrival.

Once the submitted data files are safely archived, the data undergo standard reformatting and banking procedures:

• The data files are reformatted using an in-house program into a common format, which is a NetCDF subset.
• Data files arising from the same instrument are combined into a single file.
• Standard parameter codes are assigned that accurately describe the data.
• Unit conversions are applied, if necessary, so that units are standardised. Oxygen concentration supplied by the originator in units of mg l^-1 is converted to µmol l^-1 by multiplying by 31.25.
• The data are screened visually and any spikes or instrument malfunctions can be clearly labelled with quality control flags.
• Comprehensive documentation is prepared describing the collection, processing and quality of each data series.
• Detailed metadata and documents are loaded to the database and linked to each series so that the information is readily available to future users.

Project Information

Proudman Oceanographic Laboratory Coastal Observatory

The Coastal Observatory was established by Proudman Oceanographic Laboratory as a coastal zone real time observing and monitoring system. The main objective is to understand a coastal sea's response both to natural forcing and to the consequences of human activity. Near real-time measurements will be integrated with coupled models into a pre-operational coastal prediction system whose results will be displayed on the World Wide Web.

The Observatory is expected to grow and evolve as resources and technology allow, all the while building up long time series. A site selection pilot study was carried out in September 2001 and the Observatory became operational in August 2002.

The site is located in Liverpool Bay and is subject to typical coastal sea processes, with strong tides, occasional large storm surges and waves, freshwater input, stable and unstable stratification, high suspended sediment concentration and biogeochemical interaction. Measurements and monitoring will focus on the impacts of storms, variations in river discharge (especially the Mersey), seasonality and blooms in Liverpool Bay.

A variety of methods will be used to obtain measurements, including:

1. Moored instruments for in situ time series of currents, temperature and salinity profiles, and surface waves and meteorology. It is hoped that turbidity and chlorophyll measurements will be made at another site as the Observatory progresses;
2. The Cefas Smartbuoy for surface properties such as nutrients and chlorophyll, starting late 2002;
3. R.V. Prince Madog to carry out spatial surveys and service moorings;
4. Instrumented ferries for near surface temperature, salinity, turbidity, chlorophyll and nutrients. The first route will be Liverpool to Douglas, Isle of Man, starting late 2002;
5. Drifters for surface currents and properties such as temperature and salinity, starting in 2004;
6. Tide gauges, with sensors for meteorology, waves, temperature and salinity, where appropriate;
7. Meteorological data from Bidston Observatory and Hilbre Island, HF radar and tide gauge sites;
8. Shore-based HF radar measuring waves and surface currents out to a range of 50 km, starting in 2003;
9. Satellite data, with infrared for sea surface temperature and visible for chlorophyll and suspended sediment.

The partners currently involved with the project are listed below:

• Proudman Oceanographic Laboratory
• British Oceanographic Data Centre
• UK Meteorological Office
• Centre for Environment, Fisheries and Aquaculture Science
• Environment Agency
• Liverpool University and Port Erin Marine Laboratory
• Bangor University School of Ocean Sciences
• National Oceanography Centre Southampton
• Department of Agriculture and Rural Development in Northern Ireland

A summary of Coastal Observatory cruises to date on R.V. Prince Madog is given in the table below:

Oceans 2025 - The NERC Marine Centres' Strategic Research Programme 2007-2012

Who funds the programme?

The Natural Environment Research Council (NERC) funds the Oceans 2025 programme, which was originally planned in the context of NERC's 2002-2007 strategy and later realigned to NERC's subsequent strategy (Next Generation Science for Planet Earth; NERC 2007).

Who is involved in the programme?

The Oceans 2025 programme was designed by and is to be implemented through seven leading UK marine centres. The marine centres work together in coordination and are also supported by cooperation and input from government bodies, universities and other partners. The seven marine centres are:

• National Oceanography Centre, Southampton (NOCS)
• Plymouth Marine Laboratory (PML)
• Marine Biological Association (MBA)
• Sir Alister Hardy Foundation for Marine Science (SAHFOS)
• Proudman Oceanographic Laboratory (POL)
• Scottish Association for Marine Science (SAMS)
• Sea Mammal Research Unit (SMRU)

Oceans2025 provides funding to three national marine facilities, which provide services to the wider UK marine community, in addition to the Oceans 2025 community. These facilities are:

• British Oceanographic Data Centre (BODC), hosted at POL
• Permanent Service for Mean Sea Level (PSMSL), hosted at POL
• Culture Collection of Algae and Protozoa (CCAP), hosted at SAMS

The NERC-run Strategic Ocean Funding Initiative (SOFI) provides additional support to the programme by funding additional research projects and studentships that closely complement the Oceans 2025 programme, primarily through universities.

What is the programme about?

Oceans 2025 sets out to address some key challenges that face the UK as a result of a changing marine environment. The research funded through the programme sets out to increase understanding of the size, nature and impacts of these changes, with the aim to:

• improve knowledge of how the seas behave, not just now but in the future;
• help assess what that might mean for the Earth system and for society;
• assist in developing sustainable solutions for the management of marine resources for future generations;
• enhance the research capabilities and facilities available for UK marine science.

In order to address these aims there are nine science themes supported by the Oceans 2025 programme:

• Climate, circulation and sea level (Theme 1)
• Marine biogeochemical cycles (Theme 2)
• Shelf and coastal processes (Theme 3)
• Biodiversity and ecosystem functioning (Theme 4)
• Continental margins and deep ocean (Theme 5)
• Sustainable marine resources (Theme 6)
• Technology development (Theme 8)
• Next generation ocean prediction (Theme 9)
• Integration of sustained observations in the marine environment (Theme 10)

In the original programme proposal there was a theme on health and human impacts (Theme 7). The elements of this Theme have subsequently been included in Themes 3 and 9.

When is the programme active?

The programme started in April 2007 with funding for 5 years.

Brief summary of the programme fieldwork/data

Programme fieldwork and data collection are to be achieved through:

• physical, biological and chemical parameters sampling throughout the North and South Atlantic during collaborative research cruises aboard NERC's research vessels RRS Discovery, RRS James Cook and RRS James Clark Ross;
• the Continuous Plankton Recorder being deployed by SAHFOS in the North Atlantic and North Pacific on 'ships of opportunity';
• physical parameters measured and relayed in near real-time by fixed moorings and ARGO floats;
• coastal and shelf sea observatory data (Liverpool Bay Coastal Observatory (LBCO) and Western Channel Observatory (WCO)) using the RV Prince Madog and RV Quest.

The data is to be fed into models for validation and future projections. Greater detail can be found in the Theme documents.

Oceans 2025 Theme 10

Oceans 2025 is a strategic marine science programme, bringing marine researchers together to increase people's knowledge of the marine environment so that they are better able to protect it for future generations.

Theme 10: Integration of Sustained Observations in the Marine Environment spans all marine domains from the sea-shore to the global ocean, providing data and knowledge on a wide range of ecosystem properties and processes (from ocean circulation to biodiversity) that are critical to understanding Earth system behaviour and identifying change. They have been developed not merely to provide long-term data sets, but to capture extreme or episodic events, and play a key role in the initialisation and validation of models. Many of these SOs will be integrated into the newly developing UK Marine Monitoring Strategy - evolving from the Defra reports Safeguarding our Seas (2002) and Charting Progress (2005), thus contributing to the underpinning knowledge for national marine stewardship. They will also contribute to the UK GOOS Strategic Plan (IACMST, 2006) and the Global Marine Assessment.

Weblink: http://www.oceans2025.org/

Oceans 2025 Theme 10, Sustained Observation Activity 11: Liverpool Bay and Irish Sea Coastal Observatory

Sustained, systematic observations of the ocean and continental shelf seas at appropriate time and space scales allied to numerical models are key to understanding and prediction. In shelf seas these observations address issues as fundamental as 'what is the capacity of shelf seas to absorb change?' encompassing the impacts of climate change, biological productivity and diversity, sustainable management, pollution and public health, safety at sea and extreme events. Advancing understanding of coastal processes to use and manage these resources better is challenging; important controlling processes occur over a broad range of spatial and temporal scales which cannot be simultaneously studied solely with satellite or ship-based platforms.

Considerable effort has been spent by the Proudman Oceangraphic Laboratory (POL) in the years 2001 - 2006 in setting up an integrated observational and now-cast modelling system in Liverpool Bay (see Figure), with the recent POL review stating the observatory was seen as a leader in its field and a unique 'selling' point of the laboratory. Cost benefit analysis (IACMST, 2004) shows that benefits really start to accrue after 10 years. In 2007 - 2012 exploitation of (i) the time series being acquired, (ii) the model-data synthesis and (iii) the increasingly available quantities of real-time data (e.g. river flows) can be carried out through Sustained Observation Activity (SO) 11, to provide an integrated assessment and short term forecasts of the coastal ocean state.

Overall Aims and Purpose of SO 11

• To continue and enlarge the scope of the existing coastal observatory in Liverpool Bay to routinely monitor the northern Irish Sea
• To develop the synthesis of measurements and models in the coastal ocean to optimize measurement arrays and forecast products. Driving forward shelf seas' operational oceanography with the direct objective of improving the national forecasting capability, expressed through links to the National Centre for Ocean Forecasting (NCOF)
• To exploit the long time-series of observations and model outputs to: a) identify the roles of climate and anthropogenic inputs on the coastal ocean's physical and biological functioning (including impacts of nutrient discharges, offshore renewable energy installations and fishing activity) taking into consideration the importance of events versus mean storms / waves, river discharge / variable salinity stratification / horizontal gradients; b) predict the impacts of climate change scenarios; and c) provide new insights to Irish Sea dynamics for variables either with seasonal cycles and interannual variability, or which show weak or no seasonal cycles
• To provide and maintain a 'laboratory' within which a variety of observational and model experiments can be undertaken (Oceans 2025 Themes 3, 6, 8, 9), including capture of extreme events
• Demonstrate the value of an integrated approach in assessment and forecasting
• Demonstrate the coastal observatory as a tool for marine management strategies through collaboration with the Environment Agency (EA), Department for Environment, Food and Rural Affairs (DEFRA), Joint Nature Conservation Commmittee (JNCC), English Nature (EN), Department of Agriculture and Rural Development (DARD), and Local Authorities, providing management information pertinent to policy (e.g. Water Framework Directive)

Measurement and Modelling Activities

• East Mooring Site: Bottom frame with full suite of physical measurements (high frequency Acoustic Doppler Current Profiler (ADCP), conductivity, temperature, turbidity and fluorescence), a Centre for Environment, Fisheries and Aquaculture Science (CEFAS) directional wavebuoy, and a CEFAS Smartbuoy collecting surface properties including salinity, temperature, turbidity, nutrients, irradiance and chlorophyll. All transmit data in real-time via Orbcomm. The Smartbuoy also collects daily water samples.
• West Mooring Site: Bottom frame with full suite of physical measurements (high frequency ADCP, conductivity, temperature, turbidity and fluorescence), CEFAS Smartbuoy.
• Spatial Survey: Four - six week intervals (determined by biofouling of optical sensors). Spatial surveys comprise of vertical profiles of CTD, suspended particulate material (SPM), some bed sediment sampling and surface and bed nutrients, phytoplankton, zooplankton.
• Ferry: The Birkenhead - Belfast ferry samples near surface (5 m depth) temperature, salinity, turbidity, chlorophyll, with data transmitted by Orbcomm. The route is scientifically varied passing through six completely different hydrodynamic regions, which significantly impact on their ecological function.
• Tide gauges: Real-time data are obtained from tide gauges operated by Mersey Docks and Harbour Company (MDHC) and the UK tide gauge network.
• Satellite imagery: Weekly composite satellite data, Advanced Very High Resolution Radiometer (AVHRR) sea surface temperature (SST) and ocean colour (chlorophyll and suspended sediment), are provided by the Remote Sensing Data Analysis Service (RSDAS) based at Plymouth Marine Laboratory (PML).
• HF radar: A phased array HF radar system (a 12-16MHz WERA HF radar) measuring surface currents and waves with maximum range 75km at a resolution of 4km for sea surface currents and for 2-D wave spectra.
• Meteorology station: With web camera, located on Hilbre Island at the mouth of the Dee Estuary
• Operational models: The Coastal Observatory uses Proudman Oceanographic Laboratory Coastal Ocean Modelling System (POLCOMS), which is part of Oceans 2025 Theme 9.

More detailed information on this Work Package is available at pages 32 - 35 of the official Oceans 2025 Theme 10 document: Oceans 2025 Theme 10

Weblink: http://www.oceans2025.org/

References:

IACMST., 2004. The Economics of Sustained Marine Measurements. IACMST Information Document, N0.11, Southampton: IACMST, 96 pp

Data Activity or Cruise Information

Data Activity

SmartBuoy deployment LB1_045/1016

Deployment and recovery

This mooring was deployed in a collaboration between Cefas and the POL Liverpool Bay Coastal Observatory. The rig was deployed during October 2007 RV Prince Madog cruise PD23/07. The rig was recovered in November 2007 during RV Prince Madog cruisePD27/07.

Rig Description

The SmartBuoy carried a suite of Cefas instruments mounted just below the surface, as well as instrumentation belonging to POL up to 15 m deep. Further information is given in the table below.

The single point mooring was composed mainly of 0.5 inch long link chain, marked by a 1.8 m diameter toroid and anchored by a half tonne clump of scrap chain.

The tables below detail the CEFAS instrumentation

Eco System Monitor- V2a (UL017) logged the following instruments:

Stand-Alone CEFAS Sensors:

The table below details the POL instrumentation

• Cefas - The Centre for Environment, Fisheries and Aquaculture Science, Lowestoft (UK)
• POL - The Proudman Oceanographic Laboratory, Liverpool (UK)

Related Data Activity activities are detailed in Appendix 1

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

Liverpool Bay Coastal Observatory Mooring Site A (COA/Site 1/Site 9)

This station is the main mooring site for the Proudman Oceanographic Laboratory (POL) Liverpool Bay Coastal Observatory and was first occupied in 2002. It is also known both as Coastal Observatory Site 1 and Site 9. POL perform two main types of activities at this station: they deploy moorings; and in addition, they take CTD profiles during each site visit. The station lies within a box of mean water depth 22.5 m with the following coordinates:

The position of this station relative to the other POL Coastal Observatory sites can be seen from the figure below.

Mooring Deployment History

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

CTD Sampling History

The CTD instrument package for these cruises was a Sea-Bird 911plus, with beam transmissometer, fluorometer, LICOR PAR sensor, LISST-25, and oxygen sensor.

Key

AC-S = Absorption and attenuation spectrophotometer
ADCP = Acoustic Doppler Current Profiler
ADV = Acoustic Doppler Velocimeter
BD = Bacterial degradation experiment
BPR = Bottom Pressure Recorder
CT = Conductivity and temperature logger
CTD = Conductivity, temperature, depth sensor
FL = Fluorometer
NAS = in-situ nutrient analyser
OBS = Optical Backscatter Turbidity meter
OXY = Oxygen sensor
PAR = PAR sensor
T = Temperature logger
TR = Transmissometer
WMS = Automatic water sampler

Related Fixed Station activities are detailed in Appendix 2

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: LB1_045/1016

Related series for this Data Activity are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.

Appendix 2: COA

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.