Search the data

Metadata Report for BODC Series Reference Number 1774237


Metadata Summary

Data Description

Data Category Multiple data types
Instrument Type
NameCategories
Sea and Sun Technology Microstructure Profiler MSS 90  water temperature sensor; salinity sensor; ADVs and turbulence probes
Instrument Mounting lowered unmanned submersible
Originating Country United Kingdom
Originator Dr Natasha Lucas
Originating Organization Bangor University School of Ocean Sciences
Processing Status banked
Online delivery of data Download available - Ocean Data View (ODV) format
Project(s) OSMOSIS
 

Data Identifiers

Originator's Identifier MSS_JC900687
BODC Series Reference 1774237
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 2013-09-13 19:18
End Time (yyyy-mm-dd hh:mm) -
Nominal Cycle Interval 1.0 decibars
 

Spatial Co-ordinates

Latitude 48.68093 N ( 48° 40.9' N )
Longitude 16.19610 W ( 16° 11.8' W )
Positional Uncertainty 0.0 to 0.01 n.miles
Minimum Sensor or Sampling Depth 5.95 m
Maximum Sensor or Sampling Depth 215.05 m
Minimum Sensor or Sampling Height 4657.2 m
Maximum Sensor or Sampling Height 4866.3 m
Sea Floor Depth 4872.25 m
Sea Floor Depth Source GEBCO1401
Sensor or Sampling Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor or Sampling Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Chart reference - Depth extracted from available chart
 

Parameters

BODC CODERankUnitsTitle
ACYCAA011DimensionlessSequence number
BVFSTP011per second squaredBrunt-Vaisala frequency squared of the water body by turbulence profiler precision CTD
CNDCZZ011Siemens per metreElectrical conductivity of the water body
CPHLPR011Milligrams per cubic metreConcentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer
CTDLOWRT1Metres per secondDownward velocity of sensor package in the water body
EPSIPM011Watts per kilogramLog10 turbulent kinetic energy dissipation {epsilon} per unit mass of the water body by turbulence profiler shear sensor
PRESPR011DecibarsPressure (spatial coordinate) exerted by the water body by profiling pressure sensor and correction to read zero at sea level
PSALPR011DimensionlessPractical salinity of the water body by conductivity cell and computation using UNESCO 1983 algorithm
PTCHEI011DegreesOrientation (pitch) of measurement platform by inclinometer
PTCHEI021DegreesOrientation (pitch) of measurement platform by inclinometer (second sensor)
SIGTEQ011Kilograms per cubic metreSigma-theta of the water body by computation from salinity and potential temperature using UNESCO algorithm
TEMPPR011Degrees CelsiusTemperature of the water body

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database


Data Access Policy

Open Data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

If the Information Provider does not provide a specific attribution statement, or if you are using Information from several Information Providers and multiple attributions are not practical in your product or application, you may consider using the following:

"Contains public sector information licensed under the Open Government Licence v1.0."


Narrative Documents

JC090 Microstructure Profiler Instrumentation

The following contains information taken from the JC090 cruise report.

The microstructure profiler deployed during the cruise was a loosely tethered MSS90 profiler (s/n 034) produced by Sea and Sun Technology GmbH and ISW Wassermesstechnik. The profiler has a drop speed of 0.85 ms-1and typically fell to approximately 200 metres producing up to seven profiles per hour. The instrument includes two PNS shear probes as well as fluorimetry, conductivity, temperature and pressure sensors.

The following table details the sensor configuration of the profiler:

Sensor Model Serial number Comments
Sea and Sun Technology (SST) microstructure profiler unit MSS 90 050 -

References

Naveira-Garabato, A. C. and Allen J.T. et al. (2012). 'Ocean Surface Mixing, Ocean Sub-mesoscale Interaction Study (OSMOSIS)'. Cruise Report No. 18 National Oceanography Centre, Southampton.

JC090 MSS90 Microstructure Profiler: Processing undertaken by BODC

A total of 676 individual ASCII .TOB files were supplied to BODC by the data originator. These were accompanied by 689 associated raw (.MRD) data files, as output directly from the profiler.

The .TOB files were reformatted to BODC internal QXF format and the originator's variables were mapped to BODC parameter codes as follows:

Originator's variable Units Description BODC parameter code Units Comments
Press dbar Pressure (spatial co-ordinate) exerted by the water body by profiling pressure sensor and corrected to read zero at sea level PRESPR01 dbar No unit conversion required
Chl_A µg l-1 Concentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer CPHLPR01 mg m-3 Equal units
vel dbar s-1 Downward velocity of sensor package in the water body CTDLOWRT m s-1 Assumption that 1 dbar ~ 1 metre
tiltx deg Orientation (pitch) of measurement platform by inclinometer PTCHEI01 deg No unit conversion required
tilty deg Orientation (pitch) of measurement platform by inclinometer (second sensor) PTCHEI02 deg No unit conversion required
peps W kg-1       Not reformatted by BODC
epsilon1 W kg-1       Not reformatted by BODC
epsilon2 W kg-1       Not reformatted by BODC
epsilon W kg-1 Log10 turbulent kinetic energy dissipation {epsilon} per unit mass of the water body by turbulence profiler shear sensor EPSIPM01 W kg-1 No unit conversion required
Tempcor °C Temperature of the water body TEMPPR01 °C No unit conversion required
Cond mS cm-1 Electrical conductivity of the water body CNDCZZ01 S m-1 unit conversion =/10
sal PSU Practical salinity of the water body by conductivity cell and computation using UNESCO 1983 algorithm PSALPR01 Dimensionless No unit conversion required
sig-t kg m-3 Sigma-theta of the water body by computation from salinity and potential temperature using UNESCO algorithm SIGTEQ01 kg m-3 No unit conversion required
th-sigma Dimensionless       Not reformatted by BODC
N2 (1 s-1)2 Brunt-Vaisala frequency squared of the water body by turbulence profiler precision CTD BVFSTP01 (1 s-1)2 No unit conversion required
N 1 s-1       Not reformatted by BODC
Thermdiss K2 s-1       Not reformatted by BODC
th-ntc Dimensionless       Not reformatted by BODC

Screening

The data were screened using BODC in-house software Edserplo. Any data that were outside of the expected range or improbable were flagged accordingly.

OSMOSIS RRS James Cook JC090 Microstructure profiles Quality Report for CPHLPR01

Negative values for chlorophyll (CPHLPR01) have been flagged, as have spikes which occur well below the chlorophyll maximum.

RRS James Cook JC090 Microstructure Profiler MSS90 Originator Processing

Sampling strategy

During cruise JC090, quasi-continuous night time measurements were taken between 2nd September 2013 and 9th September 2013 amounting to 327 profiles. Following mooring recovery, shifts were changed in order to allow for longer profiling series. Measurements were then taken between 9th September 2013 and 13th September 2013 amounting to 362 profiles.

The following table summarises the profiles made:

Session number Start date/time (YYYY-MM-DD HH:MM GMT) End date/time (YYYY-MM-DD HH:MM GMT) Total time (HH:MM) Number of profiles Comments
1 2013-09-02 21:56 2013-09-03 05:11 07:15 46 -
2 2013-09-03 21:04 2013-09-04 05:17 08:13 52 -
3 2013-09-04 23:41 2013-09-05 06:48 07:07 32 -
4 2013-09-05 20:21 2013-09-06 06:41 10:20 40 -
5 2013-09-06 19:52 2013-09-07 07:02 11:10 56 -
6 2013-09-07 19:11 2013-09-08 08:41 13:30 61 -
7 2013-09-08 19:59 2013-09-09 02:46 06:47 40 Shift change caused early finish.
8 2013-09-09 17:25 2013-09-10 05:53 12:28 68 -
9 2013-09-10 09:42 2013-09-11 04:39 18:57 112 Winch transformer breakdown. Repaired for next session.
10 2013-09-11 18:40 2013-09-12 14:43 20:03 114 -
11 2013-09-12 20:08 2013-09-13 01:34 05:26 33 Stopped due to starboard prop failure. Cable reterminated for next session.
12 2013-09-13 13:36 2013-09-13 19:40 06:04 35 -

The profiler was deployed from a winch and allowed to freefall to approximately 200 metres. A complete profile took 8-10 minutes, producing approximately 6-7 profiles an hour. The ship's speed relative to the water was held at 0.3-0.5 knots where possible to avoid the line being drawn back under the ship. The data were continuously recorded onto a PC laptop connected to the profiler via a slack tether and winch system.

Data processing

Data were processed from raw shear signals through to TKE dissipation rate using the MSSPRO software standard processing sequence and formattetd into ASCII(.TOB) files. A summary of the main SAMS processing steps is presented below. More comprehensive details are available in the MSSpro software manual .

  • Conversion of sensor output voltages to shear measurements using the gradient of velocity as a function of pressure through the water column
  • Application of calibration coefficients specific to the shear probes
  • Checking of shear spectra with Nasmyth's universal spectrum of turbulence in the ocean and subsequent application of a low pass filter to remove high frequency noise from the profiles
  • Calculation of the dissipation rate of turbulent kinteic energy (epsilon) over the measurable range from the profiler. Spectral fitting using the Nasmyth spectrum to address those frequencies outside of the range
  • Generation of 1 metre-binned ASCII (.tob) files containing the key variables identified by the originator.

Note

The raw .MRD files for this cruise are preserved in the BODC archive and are available on request.

References

Naveira-Garabato, A. C. et al. (2013). 'Ocean Surface Mixing, Ocean Sub-mesoscale Interaction Study (OSMOSIS)'. Cruise Report No. 25 National Oceanography Centre, Southampton.

Sea and Sun Technology MSS 90 Microstructure Profiler

A multiparameter probe used to measure micro-scale water stratification as well as the intensity of small scale turbulence in the water column in marine and limnic environments. The instrument can be used for free sinking or rising measurements. The instruments sinking or rising velocity can be adjusted by a combination of weights and buoyancy elements. It has a depth rating of approximately 500 m, samples at 1024 Hz and is equipped with high resolution micro-structure and turbulence sensors (temperature, current shear) and standard CTD sensors (temperature, conductivity, pressure). All microstructure channels have a response time of less than 12 ms. The unit includes internal sensors to control for vibrations and tilt internally.

The system comprises the profiler, a winch, a probe interface and data acquisition computer. Additional sensors, such as oxygen and optical scattering, can be attached to the profiler. The instrument can support up to a maximum of nine sensors.

There are two different models available which have the same electronic and sensor equipment, with the difference relating to the size and weight of the instruments, see the table below for further details. The shear sensor data quality of the MSS90L is however superior due to the higher mass and stability.

Technical Data/Dimensions MSS 90 MSS 90L
Depth range 500 m 500 m
Weight in water 10 kg 12.5 kg
Depth range 500 m 500 m
Length of housing 1 m 1.25 m
Standard sensor equipment Pressure, temperature and conductivity
2 x Shear
Temperature microstructure sensor FP07
Acceleration sensor for measuring the profiler vibration
Pressure, temperature and conductivity
2 x Shear
Temperature microstructure sensor FP07
Acceleration sensor for measuring the profiler vibration
Sensor plugs 9 9
Optional sensors Turbidity
Fluorescence
Tilt (2axis)
Oxygen
pH
Turbidity
Fluorescence
Tilt (2axis)
Oxygen
pH
Data channels 16 16
Sampling rate 1024 s-1 1024 s-1
Resolution 16 Bit 16 Bit
Housing Seamless drawn titanium tube Seamless drawn titanium tube
Channels response time <12 ms <12 ms

Further details can be found in the manufacturer's manual.


Project Information

Ocean Surface Mixing, Ocean Sub-mesoscale Interaction Study (OSMOSIS)

Background

The Ocean Surface Mixing, Ocean Sub-mesoscale Interaction Study (OSMOSIS) consortium was funded to deliver NERC's Ocean Surface Boundary Layer (OSBL) programme. Commencing in 2011, this multiple year study will combine traditional observational techniques, such as moorings and CTDs, with the latest autonomous sampling technologies (including ocean gliders), capable of delivering near real-time scientific measurements through the water column.

The OSMOSIS consortium aims to improve understanding of the OSBL, the interface between the atmosphere and the deeper ocean. This layer of the water column is thought to play a pivotal role in global climate and the productivity of our oceans.

OSMOSIS involves collaborations between scientists at various universities (Reading, Oxford, Bangor, Southampton and East Anglia) together with researchers at the National Oceanography Centre (NOC), Scottish Association for Marine Science (SAMS) and Plymouth Marine Laboratory (PML). In addition, there are a number of project partners linked to the consortium.

Scientific Objectives

  • The primary goal of the fieldwork component of OSMOSIS is to obtain a year-long time series of the properties of the OSBL and its controlling 3D physical processes. This is achieved with an array of moorings (two nested clusters of 4 moorings, each centred around a central mooring) and gliders deployed near the Porcupine Abyssal Plain (PAP) observatory. Data obtained from this campaign will help with the understanding of these processes and subsequent development of associated parameterisations.
  • OSMOSIS will attempt to create parameterisations for the processes which determine the evolving stratification and potential vorticity budgets of the OSBL.
  • The overall legacy of OSMOSIS will be to develop new (physically based and observationally supported) parameterisations of processes that deepen and shoal the OSBL, and to implement and evaluate these parameterisations in a state-of-the-art global coupled climate model, facilitating improved weather and climate predictions.

Fieldwork

Three cruises are directly associated with the OSMOSIS consortium. Preliminary exploratory work in the Clyde Sea (September 2011) to hone techniques and strategies, followed by a mooring deployment and recovery cruise in the vicinity of the Porcupine Abyssal Plain (PAP) observatory (in late Summer 2012 and 2013 respectively). Additional opportunist ship time being factored in to support the ambitious glider operations associated with OSMOSIS.

Instrumentation

Types of instrumentation and measurements associated with the OSMOSIS observational campaign:

  • Ocean gliders
  • Wave rider buoys
  • Towed SeaSoar surveys
  • Microshear measurements
  • Moored current meters, conductivity-temperature sensors and ADCPs
  • Traditional shipboard measurements (including CTD, underway, discrete nutrients, LADCP, ADCP).

Contacts

Collaborator Organisation
Prof. Stephen Belcher University of Reading, U.K
Dr. Alberto C Naveira Garabato University of Southampton, U.K

Data Activity or Cruise Information

Cruise

Cruise Name JC090
Departure Date 2013-08-31
Arrival Date 2013-09-16
Principal Scientist(s)Alberto C Naveira Garabato (University of Southampton School of Ocean and Earth Science)
Ship RRS James Cook

Complete Cruise Metadata Report is available here


Fixed Station Information


No Fixed Station Information held for the Series


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain
B nominal value
Q value below limit of quantification