Metadata Report for BODC Series Reference Number 648686

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

Data quality report

Suspect values were identified during screening where current speed and direction both dropped to zero for two or more consecutive data cycles. This is likely to be the result of temporary fouling of the current meter rotor. These suspect data points have been flagged M. Where a small number of non-zero points occur within a long series of zeroes the non-zero data have also been flagged M as it is unlikely that rotor movement was entirely free for a short number of data cycles before the instrument became jammed again.

Data Access Policy

Public domain data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

The recommended acknowledgment is

"This study uses data from the data source/organisation/programme, provided by the British Oceanographic Data Centre and funded by the funding body."

Narrative Documents

Aanderaa Recording Current Meter Model 7/8

Manufacturer's specifications: recording unit height 49.5cm (RCM8 52.0cm), diameter 12.8cm, vane size 48.5x50.0cm. Meter is designed for depths down to 2000m (RCM8 6000m). It incorporates a spindle which is shackled to the mooring line. The meter is attached to the spindle through a gimbal mounting which permits a maximum 27° deviation of the spindle from the vertical, the meter still remaining horizontal.

Meter comprises :

1. Paddle wheel rotor magnetically coupled to an electronic counter

2. Vane, which aligns instrument with current flow, has a balance weight ensuring static balance and tail fins to ensure dynamic balance in flows up to 250cm/s.

3. Magnetic compass (needle is clamped to potentiometer ring) - direction recorded with 0.35° resolution, 5° accuracy for speeds 5 to 100cm/s, 7.5° accuracy for remaining speeds within 2.5 to 200cm/s range.

4. Quartz clock, accuracy better than 2 sec/day within temperature range 0 to 20°C.

5. Thermistor (temperature sensor), standard range -2.46 to 21.48°C (max on high range 36.04°C), accuracy 0.05°C, resolution 0.1 per cent of range, 63 per cent response time 12sec.

6. Inductive cell conductivity sensor (optional), range 0 to 70mmho/cm standard resolution 0.1 per cent of range.

7. Silicon piezoresistive bridge, standard range 0 to 3000 psi (RCM8 to 9000 psi), resolution 0.1% of range.

8. Self balancing potentiometer which converts the output from each sensor into a 10 bit binary number for storage on magnetic tape.

9. Associated electronics.

A built-in clock triggers the instrument at preset intervals and up to six channels are sampled in sequence. Channel 1 is a fixed reference reading for control purposes and data identification. Channels 2, 3 and 4 represent measurement of temperature, conductivity and pressure. Channels 5 and 6 represent the VECTOR AVERAGED current speed and direction since the previous triggering of the instrument. The number of rotor revolutions and the direction is sampled every 12 seconds and broken into North and East components. Successive components are added and recorded as speed and direction. For recording intervals longer than 10 minutes, speed and direction are sampled 1/50th of recording interval.

It has become common practice in some laboratories to deploy these meters as temperature and conductivity loggers without current measuring capabilities.

The following link will provide the manufacturer specifications:

BODC Processing

Data were received by BODC in ASCII format files. This series was reformatted to the internal QXF format using BODC transfer function 325. The following table shows how the variables within the file were mapped to the appropriate BODC parameter codes.

Following transfer to QXF, the data were screened using BODC's in-house visualisation software, EDSERPLO. Any data considered as suspect were flagged 'M'. Flags from the originator marking suspect data were retained during transfer and flagged 'L'.

Originator's Data Processing

Sampling Strategy

The Aanderaa RCM 7 current meter deployed on the Wyville-Thompson Ridge had a sampling frequency of 1 reading per hour. The instrument included a temperature sensor.

Data Processing

DAF applied the standard manufacturers' calibrations to all current, temperature and salinity data, and produced ASCII files for submission to BODC. Data files were named according to the mooring code (701) and the instrument number (4). The current meter file (7014) contained eastward and northward velocities, and temperature.

Project Information

No Project Information held for the Series

Data Activity or Cruise Information

Data Activity

DAF current meter mooring, Wyville-Thompson Ridge

The mooring was located at 60° 16.24' N, 009° 0.80' W in a nominal water depth of 986 m.

The mooring was deployed on 20 May 2004 by the Department of Agriculture and Fisheries (DAF, now known as Marine Scotland Aberdeen Marine Laboratory) on cruise FRV Scotia 0804S (Part 1) (12 May 2004-30 May 2004), recovered on 24 February 2005, and consisted of the following instruments.

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

No Fixed Station Information held for the Series

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle: