Metadata Report for BODC Series Reference Number 747684
Metadata Summary
Problem Reports
Data Access Policy
Narrative Documents
Project Information
Data Activity or Cruise Information
Fixed Station Information
BODC Quality Flags
SeaDataNet Quality Flags
Metadata Summary
Data Description |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Data Identifiers |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Time Co-ordinates(UT) |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Spatial Co-ordinates | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Parameters |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Problem Reports
No Problem Report Found in the Database
Quality Reports
Cast CO15/04/27, CO15/04/28 and CO15/04/29; have constant suspended particulate material {TSEDBSCL} readings of 28 mg/l. However temperature and salinity profiles are stratified which suggests a problem with the sensor.
Data flagged and should be used with caution.
Data Access Policy
Public domain data
These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.
The recommended acknowledgment is
"This study uses data from the data source/organisation/programme, provided by the British Oceanographic Data Centre and funded by the funding body."
Narrative Documents
Falmouth Scientific Integrated CTD (ICTD) Profiler
The FSI ICTD is designed to collect high precision conductivity, temperature and pressure data with self calibrating electronics. This instrument can support five primary sensors (including up to three temperature sensors) and can be coupled with a water bottle sampler. The ICTD is equipped with a titanium housing rated to 7000 m and has a sampling rate of 32 Hz.
Three temperature sensors are available: primary platinum, redundant platinum and exposed thermistor. Any combination of these can be used in the primary channels. The instrument also has multiple RS-232 serial inputs for a variety of sensors including: ADCP, Benthos PSA-916 Altimeter and WetLabs SAFire. There are an additional eight DC input channels that can support virtually any sensor that has a DC output.
Specifications:
| Parameter | Conductivity | Temperature | Pressure |
| Sensor | Inductive cell | Platinum thermometer | Precision-machined Silicon |
| Range | 0 to 70 mS cm-1 | -2 to 35°C | Customer specified |
| Accuracy | ±0.002 mS cm-1 | 0.002°C | ±0.01 % full scale |
| Resolution | 0.0001 mS cm-1 | 0.00005°C | 0.0004 % full scale |
| Response | 5.0 cm at 1 ms-1 | 150 ms Platinum 20 ms Thermistor* | 25 ms |
*Optional
Further details can be found in the manufacturer's specification sheet.
Seapoint Chlorophyll Fluorometer
The Seapoint Chlorophyll Fluorometer (SCF) is a low power instrument for in situ measurements of chlorophyll a. The SCF uses modulated blue LED lamps and a blue excitation filter to excite chlorophyll a. The fluorescent light emitted by the chlorophyll a passes through a red emission filter and is detected by a silicon photodiode. The low level signal is then processed using synchronous demodulation circuitry which generates an output voltage proportional to chlorophyll a concentration. The SCF may be operated with or without a pump.
Sensor specifications, current at August 2006, are given in the table below. More information can be found at the manufacturer's web site.
Sensor Specifications
| Power requirements | 8 - 20 VDC, 15 mA avg., 27 mA pk. |
|---|---|
| Output | 0 - 5.0 VDC |
| Output Time Constant | 0.1 sec. |
| Power-up transient period | < 1 sec. |
| Excitation Wavelength | 470 nm CWL, 30 nm FWHM |
| Emission Wavelength | 685 nm CWL, 30 nm FWHM |
| Sensing Volume | 340 mm3 |
| Minimum Detectable Level | 0.02 µg l-1 |
| Gain | Sensitivity, V µg-1 l-1 | Range, µg l-1 | |
|---|---|---|---|
| Sensitivity/Range | 30x 10x 3x 1x | 1.0 0.33 0.1 0.033 | 5 15 50 150 |
LI-COR LI-192 Underwater Quantum Sensor
The LI-192 Underwater Quantum Sensor is used to measure photosynthetic photon flux density and is cosine corrected. The sensor is often referred to as LI-192SA or LI-192SB (the LI-192SB model was superseded by LI-192SA). One of the main differences is that the LI-192SA model includes a built-in voltage output for interfacing with NexSens iSIC and SDL data loggers.
Sensor specifications, current at January 2012, are given in the table below. More information can be found in the manufacturer's LI-192SA andLI-192SB specification sheets.
Sensor Specifications
(Specifications apply to both models unless otherwise stated)
| Absolute Calibration | ± 5 % in air traceable to NBS. |
|---|---|
| Sensitivity | Typically 3 µA per 1000 µmol s-1 m-2 for LI-192SB and 4 µA per 1000 µmol s-1 m-2 for LI-192SA in water. |
| Linearity | Maximum deviation of 1 % up to 10,000 µmol s-1 m-2. |
| Stability | < ± 2 % change over a 1 year period. |
| Response Time | 10 µs. |
| Temperature Dependence | ± 0.15 % per °C maximum. |
| Cosine Correction | Optimized for both underwater and atmospheric use. |
| Azimuth | < ± 1 % error over 360 ° at 45 ° elevation. |
| Detector | High stability silicon photovoltaic detector (blue enhanced). |
| Sensor Housing | Corrosion resistant metal with acrylic diffuser for both saltwater and freshwater applications. Waterproof to withstand 800 psi (5500 kPa) (560 meters). |
Seapoint Turbidity Meter
The Seapoint Turbidity Meter detects light scattered by particles suspended in water, generating an output voltage proportional to turbidity or suspended solids. Range is selected by two digital lines which can be hard wired or microprocessor controlled, thereby choosing the appropriate range and resolution for measurement of extremely clean to very turbid waters. The offset voltage is within 1 mV of zero and requires no adjustment across gains. The optical design confines the sensing volume to within 5 cm of the sensor allowing near-bottom measurements and minimizing errant reflections in restricted spaces.
Sensor specifications, current at August 2006, are given in the table below.
Sensor Specifications
| Power requirements | 7 - 20 VDC, 3.5 mA avg., 6 mA pk. |
|---|---|
| Output | 0 - 5.0 VDC |
| Output Time Constant | 0.1 sec. |
| RMS Noise> | < 1 mV |
| Power-up transient period | < 1 sec. |
| Light Source Wavelength | 880 nm |
| Sensing Distance (from windows) | < 5 cm (approx.) |
| Linearity | < 2% deviation 0 - 750 FTU |
| Gain | Sensitivity (mV FTU-1) | Range (FTU) | |
|---|---|---|---|
| Sensitivity/Range | 100x 20x 5x 1x | 200 40 10 2 | 25 125 500 ** |
** output is non-linear above 750 FTU.
Further details can be found in the manufacturer's specification sheet.
RV CORYSTES: CRUISE 15/04: CTD data document
Sampling strategy
A total of 14 full depth CTD profiles were obtained. CTD were deployed at West Gabbard and at the Warp. CTD profiles were not collected during the transect between the Warp and West Gabbard due to the weather.
For further detail please refer to the cruise report
Instrument Description
Instrumentation and data processing
The CTD used was a Falmouth Scientific Inc with serial number 1351. Samples were collected for salinity analysis (using a Guildline salinometer) to derive a calibration for the instrument conductivity sensor. A pair of digital reversing thermometers were used to compare with the CTD temperature estimates. A CHELSEA fluorometer and SEAPOINT turbidity sensor were used at all CTD stations. A LICOR photosynthetically-active- radiation sensor (with a six-decade log amplifier was fitted to the rosette at all CTD stations. Chlorophyll samples were collected to calibrate the fluorometer and samples for suspended particulate matter analysis were used to calibrate the turbidity sensor.
A list of calibrated parameters and instrumentation used is shown below.
| Measurment | Parameter | Units | Instrumentation | Calibration |
|---|---|---|---|---|
| pres | Pressure | dbar | Not listed | Corrected from deck measurements |
| temp | Temperature | °C | Temperature sensor | Calibrated December 2004 |
| salinity | Salinity | n/a | Guildline Salinometer | Calibrated against bottle samples |
| turb | Turbidity | volts | Seapoint Turbidity sensor | Calibrated against bottle samples |
| sl | Suspended Load | mg/L | Seapoint Turbidity sensor | Used to calibrate turbidity |
| light | Light | volts | Licor Light sensor (s/n 5672) | Used to calculate PAR |
| fluor | Fluorescence | volts | Seapoint Fluorometer | Calibrated against bottle samples |
Change of sensors during cruise: None reported.
The data sets were calibrated by CEFAS:
(a) Pressure
During the cruise the 'on deck' CTD pressure immediately prior to lowering the CTD was recorded. These 'on deck' observations have been used to correct recorded CTD pressure as follows:
P(cor) = P(unc) + dP
| Station | Pctd on deck |
|---|---|
| 2 | -0.05 |
| 3 | -0.05 |
| 5 | -0.05 |
| 6 | -0.067 |
| 9 | -0.083 |
| 11 | -0.0667 |
| 12 | -0.1 |
| 21 | -0.15 |
| 27 | -0.18 |
| 28 | -0.14 |
| 29 | -0.13 |
| 31 | -0.14 |
| 29 | -0.13 |
| Mean | -0.1 |
dp = 0.1 was used in the CTD (pressure sensor) calibration
(b) Temperature
The Platinum Resistance Thermometer (PRT) temperature sensor fitted to CTD 1351 was calibrated using PRT's during December 2004, and this was used to correct the CTD temperature :
T(cor) = T(unc) + dT
dT = a*T(unc)*T(unc) + b*T(unc) + c
where
a = 1.42e-5 b = -2.734e-4 c = -1.7166e-3 for s/n 1322
(c) Conductivity
For this cruise it is assumed that the tolerance between salinity (water samples) and CTD (salinity) is accurate to 0.1 plus the manufacturer tolerance of 0.003. Most of the stations for CTD s/n 1351B, 1366B and 1397B are within the required tolerance. All CTD readings not within this tolerance have not been used for any calculations. Salinometer reading takes precedence over the CTD reading.
A least square fit was used to determine appropriate calibration coefficients:
CR(cor) = CR(ctd) [a*T(cor) + b*P(cor) + c]
where T(cor) and P(cor) are the corrected CTD temperature and pressure and
s/n 1322B
a -3.117E-06
b -1.473E-06
c 1.00040132
Using these coefficients the rms difference between water sample (salinometer) and corrected CTD salinity for s/n 1322B is 0.004 (26 values).
d) Suspended Load - Turbidity Sensor Calibration
The Seapoint turbidity sensor was calibrated by comparing recorded voltages with samples collected (during ascent of the CTD) for suspended load analysis
suspended load (mg/l) = a * Turbidity (volts) + b
where
a = 7.99E+00 b = -8.51E+00 R2 = 0.6861 (for stations 2 - 32)
e) Fluorometer - Chlorophyll Calibration
A Seapoint fluorometer (s/n unknown) was fitted to the rosette sampler and used to estimate chlorophyll levels. The sensor was calibrated by comparing recorded voltages with measured chlorophyll of samples collected in niskin bottles as the CTD rosette returned to the surface.
Chlorophyll (ug/l) = a*Fluorometer (volts) + b
a = 81.97 b = -1.131 R2 = 0.815 (for stations 2 - 32)
f) Photosynthetically Active Radiation
The Licor light sensor (s/n 5672) was calibrated according to the LiCor Amplifier and Sensor calibrations which gave overall factors for calculating uE s-1 m-2.
Offset X=3.44824
L.C=0.170237
BODC post-processing and screening
Reformatting
Data for the 14 CTD casts was provided in ASCII format as .cor files. The data files were converted from ASCII format into BODC internal format (QXF). Source file parameters have been mapped to BODC parameter codes (see table below). No unit conversions were necessary.
| Originators Parameter | Units | Description | BODC Parameter | BOBC Units | Comments |
|---|---|---|---|---|---|
| Pres | dbars | Pressure | PRESPR01 | dbars | Calibration by Cefas |
| Temp | deg C | Temperature | TEMPCC01 | deg C | Calibration by Cefas |
| Salinity | no units | Salinity | PSALCC01 | no units | Calibration by Cefas |
| Pot | deg C | Potential Temperature | POTMCV01 | deg C | Derived from temperature readings |
| SVEL | m/sec | Sound Velocity | SVELCT01 | m/sec | - |
| Sig-th | kg m-3 | Sigma-Theta | SIGTPR01 | kg m-3 | - |
| Sigma-t | kg m-3 | Sigma-t | SIGTEQST | kg m-3 | - |
| Svan | 10-8 | Specific volume anomaly | - | 10-8 | Not transfered |
| dynht | - | Dynamic Hight | No data | - | Not transfered |
| bvf | cph | Brunt Wiesler frequency | - | cph | Not transfered |
| Depth | M | Depth | DEPHFP01 | M | Calculated from pressure readings |
| Turb | Volts | Turbidity | NVLTSP01 | Volts | Raw voltages - uncalibrated |
| sl | mg/L | Suspended load | TSEDBSCL | mg/L | Calibrated by Cefas |
| light | Volts | - | LVLTLD01 | Volts | Raw voltages - uncalibrated |
| PAR | µE M-2 S-1 | Photosynthetically Active Radiation | IRRDUV01 | µE M-2 S-1 | Calibrated by Cefas |
| Fluor | Volts | Fluorescence | FVLTWS01 | Volts | Used to calculate chlorophyll |
| Chl | mg/m3 | Chlorophyll | CPHLPS01 | mg/m3 | Calibrated by Cefas |
Parameters such as Specific Volume Anomaly (SVAN) were not transferred as they are not considered environmental measurements and can be readily reproduced from the other data.
Screening
Reformatted CTD data were visualised using the in-house editor EDSERPLO. EDSERPLO provides a graphical representation of the data so that parameters can be checked for anomolies. All parameters were plotted against depth. Checks include identifying data spikes, gaps in the data and values that lie outside of expected limits for the environment. No data values are deleted. Suspect data are marked by adding an appropriate quality control flag.
Project Information
No Project Information held for the Series
Data Activity or Cruise Information
Cruise
| Cruise Name | COR15/04 |
| Departure Date | 2004-10-13 |
| Arrival Date | 2004-10-14 |
| Principal Scientist(s) | David Brian Sivyer (Centre for Environment, Fisheries and Aquaculture Science Lowestoft Laboratory) |
| Ship | RV Corystes |
Complete Cruise Metadata Report is available here
Fixed Station Information
No Fixed Station Information held for the Series
BODC Quality Control Flags
The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:
| Flag | Description |
|---|---|
| Blank | Unqualified |
| < | Below detection limit |
| > | In excess of quoted value |
| A | Taxonomic flag for affinis (aff.) |
| B | Beginning of CTD Down/Up Cast |
| C | Taxonomic flag for confer (cf.) |
| D | Thermometric depth |
| E | End of CTD Down/Up Cast |
| G | Non-taxonomic biological characteristic uncertainty |
| H | Extrapolated value |
| I | Taxonomic flag for single species (sp.) |
| K | Improbable value - unknown quality control source |
| L | Improbable value - originator's quality control |
| M | Improbable value - BODC quality control |
| N | Null value |
| O | Improbable value - user quality control |
| P | Trace/calm |
| Q | Indeterminate |
| R | Replacement value |
| S | Estimated value |
| T | Interpolated value |
| U | Uncalibrated |
| W | Control value |
| X | Excessive difference |
SeaDataNet Quality Control Flags
The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:
| Flag | Description |
|---|---|
| 0 | no quality control |
| 1 | good value |
| 2 | probably good value |
| 3 | probably bad value |
| 4 | bad value |
| 5 | changed value |
| 6 | value below detection |
| 7 | value in excess |
| 8 | interpolated value |
| 9 | missing value |
| A | value phenomenon uncertain |
| B | nominal value |
| Q | value below limit of quantification |
