Search the data

Metadata Report for BODC Series Reference Number 966383


Metadata Summary

Data Description

Data Category CTD or STD cast
Instrument Type
NameCategories
Neil Brown MK3 CTD  CTD; water temperature sensor; salinity sensor; dissolved gas sensors
SeaTech transmissometer  transmissometers
Chelsea Technologies Group Aquatracka fluorometer  fluorometers
Chelsea Technologies Group 2-pi PAR irradiance sensor  radiometers
Instrument Mounting research vessel
Originating Country United Kingdom
Originator Prof Fauzi Mantoura
Originating Organization Plymouth Marine Laboratory
Processing Status banked
Online delivery of data Download available - Ocean Data View (ODV) format
Project(s) ARABESQUE
 

Data Identifiers

Originator's Identifier GOM6A/2
BODC Series Reference 966383
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 1994-09-02 00:56
End Time (yyyy-mm-dd hh:mm) -
Nominal Cycle Interval 1.0 decibars
 

Spatial Co-ordinates

Latitude 21.81117 N ( 21° 48.7' N )
Longitude 62.35517 E ( 62° 21.3' E )
Positional Uncertainty 0.0 to 0.01 n.miles
Minimum Sensor or Sampling Depth 1.49 m
Maximum Sensor or Sampling Depth 14.41 m
Minimum Sensor or Sampling Height 3061.29 m
Maximum Sensor or Sampling Height 3074.21 m
Sea Floor Depth 3075.7 m
Sea Floor Depth Source -
Sensor or Sampling Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor or Sampling Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
 

Parameters

BODC CODERankUnitsTitle
ATTNZR011per metreAttenuation (red light wavelength) per unit length of the water body by transmissometer
CPHLPR011Milligrams per cubic metreConcentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer
DOXYPR011Micromoles per litreConcentration of oxygen {O2 CAS 7782-44-7} per unit volume of the water body [dissolved plus reactive particulate phase] by in-situ Beckmann probe
IRRDPP011MicroEinsteins per square metre per secondDownwelling 2-pi scalar irradiance as photons of electromagnetic radiation (PAR wavelengths) in the water body by 2-pi scalar radiometer
OXYSBB011PercentSaturation of oxygen {O2 CAS 7782-44-7} in the water body [dissolved plus reactive particulate phase] by in-situ Beckmann probe and computation from concentration using Benson and Krause algorithm
POATCV011per metrePotential attenuance (unspecified wavelength) per unit length of the water body by transmissometer and computation using P-EXEC algorithm
POTMCV011Degrees CelsiusPotential temperature of the water body by computation using UNESCO 1983 algorithm
PRESPR011DecibarsPressure (spatial coordinate) exerted by the water body by profiling pressure sensor and correction to read zero at sea level
PSALST011DimensionlessPractical salinity of the water body by CTD and computation using UNESCO 1983 algorithm
SIGTPR011Kilograms per cubic metreSigma-theta of the water body by CTD and computation from salinity and potential temperature using UNESCO algorithm
TEMPST011Degrees CelsiusTemperature of the water body by CTD or STD

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database

Data Quality Report

Due to a zeroing problem with the fluorometer, spurious chlorophyll concentrations were occasionally observed at depth. Any concentrations exceeding 0.1mg/m3 at depths of 200 metres or more have been flagged suspect.


Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."


Narrative Documents

Neil Brown MK3 CTD

The Neil Brown MK3 conductivity-temperature-depth (CTD) profiler consists of an integral unit containing pressure, temperature and conductivity sensors with an optional dissolved oxygen sensor in a pressure-hardened casing. The most widely used variant in the 1980s and 1990s was the MK3B. An upgrade to this, the MK3C, was developed to meet the requirements of the WOCE project.

The MK3C includes a low hysteresis, titanium strain gauge pressure transducer. The transducer temperature is measured separately, allowing correction for the effects of temperature on pressure measurements. The MK3C conductivity cell features a free flow, internal field design that eliminates ducted pumping and is not affected by external metallic objects such as guard cages and external sensors.

Additional optional sensors include pH and a pressure-temperature fluorometer. The instrument is no longer in production, but is supported (repair and calibration) by General Oceanics.

Specifications

These specification apply to the MK3C version.

Pressure Temperature Conductivity
Range

6500 m

3200 m (optional)

-3 to 32°C 1 to 6.5 S cm-1
Accuracy

0.0015% FS

0.03% FS < 1 msec

0.0005°C

0.003°C < 30 msec

0.0001 S cm-1

0.0003 S cm-1 < 30 msec

Further details can be found in the specification sheet.

Aquatracka fluorometer

The Chelsea Instruments Aquatracka is a logarithmic response fluorometer. It uses a pulsed (5.5 Hz) xenon light source discharging between 320 and 800 nm through a blue filter with a peak transmission of 420 nm and a bandwidth at half maximum of 100 nm. A red filter with sharp cut off, 10% transmission at 664 nm and 678 nm, is used to pass chlorophyll-a fluorescence to the sample photodiode.

The instrument may be deployed either in a through-flow tank, on a CTD frame or moored with a data logging package.

Further details can be found in the manufacturer's specification sheet.

Chelsea Technologies Photosynthetically Active Radiation (PAR) Irradiance Sensor

This sensor was originally designed to assist the study of marine photosynthesis. With the use of logarithmic amplication, the sensor covers a range of 6 orders of magnitude, which avoids setting up the sensor range for the expected signal level for different ambient conditions.

The sensor consists of a hollow PTFE 2-pi collector supported by a clear acetal dome diverting light to a filter and photodiode from which a cosine response is obtained. The sensor can be used in moorings, profiling or deployed in towed vehicles and can measure both upwelling and downwelling light.

Specifications

Operation depth 1000 m
Range 2000 to 0.002 µE m-2 s-1
Angular Detection Range ± 130° from normal incidence
Relative Spectral Sensitivity

flat to ± 3% from 450 to 700 nm

down 8% of 400 nm and 36% at 350 nm

Further details can be found in the manufacturer's specification sheet.

SeaTech Transmissometer

Introduction

The transmissometer is designed to accurately measure the the amount of light transmitted by a modulated Light Emitting Diode (LED) through a fixed-length in-situ water column to a synchronous detector.

Specifications

  • Water path length: 5 cm (for use in turbid waters) to 1 m (for use in clear ocean waters).
  • Beam diameter: 15 mm
  • Transmitted beam collimation: <3 milliradians
  • Receiver acceptance angle (in water): <18 milliradians
  • Light source wavelength: usually (but not exclusively) 660 nm (red light)

Notes

The instrument can be interfaced to Aanderaa RCM7 current meters. This is achieved by fitting the transmissometer in a slot cut into a customized RCM4-type vane.

A red LED (660 nm) is used for general applications looking at water column sediment load. However, green or blue LEDs can be fitted for specilised optics applications. The light source used is identified by the BODC parameter code.

Further details can be found in the manufacturer's Manual.

RRS Discovery 210 (D210) and RRS Discovery 212 (D212) CTD Data Documentation

Introduction

During the two ARABESQUE cruises (D210, August - September1994 and D 212, October - November 1994), nearly 300 CTD casts were taken. This document describes the CTD data from both cruises. It includes measurements made from the standard CTD unit (salinity derived from conductivity, temperature and depth) and from additional instrumentation attached to the CTD frame (a fluorometer, transmissometer, dissolved oxygen electrode and downwelling and upwelling PAR sensors). This document details the protocols used during data acquisition and processing.

Please note that all times given are in GMT which is local ship time minus four hours.

Instrumentation and Rig Geometry

The 289 CTD profiles were taken with an RVS Neil Brown Systems Mk3B CTD incorporating a pressure sensor, conductivity cell, platinum resistance thermometer and a Beckman dissolved oxygen sensor. The CTD unit was mounted vertically in the centre of a protective cage approximately 1.5 m square. Attached to the bars of the frame was a Chelsea Instruments Aquatracka fluorometer and a SeaTech red light (661 nm) transmissometer with a 25 cm pathlength.

A General Oceanics rosette sampler fitted with 12, 10 litre Niskin or lever action Niskin bottles was mounted above the frame. The bases of the bottles were 0.75 m above the pressure head with their tops 1.55 m above it. One of the bottles was fitted with a holder for up to three digital reversing thermometers mounted 1.38 m above the CTD temperature sensor.

Lowering rates were generally in the range of 0.5-1.0 m/sec but could be up to 1.5 m/sec. Bottle samples were acquired on the ascent of all casts. Reversing thermometer readings were taken on 186 of the 289 casts.

Data Acquisition

The CTD sampled at a frequency of 32 Hz. These data were reduced in real time to a 1-second time series by the RVS Level A microcomputer system. These data were logged as raw counts on the Level C workstation via a Level B data buffer.

On-Board Data Processing

RVS software on the Level C (a SUN workstation) was used to convert the raw counts into engineering units (Volts for the transmissometer and fluorometer, ml/l for oxygen,mmho.cm-1 for conductivity and °C for temperature).

Salinity (Practical Salinity Units, as defined by the Practical Salinity Scale (Fofonoff and Millard 1982)) was calculated from the conductivity ratios (conductivity / 42.914) and a time lagged temperature.

Data were written onto Quarter Inch Cartridge tapes in RVS internal format and submitted to BODC for post-cruise processing and data-banking.

Post-Cruise Processing

Reformatting

The data were converted into the BODC internal format to allow the use of in-house software tools, notably the workstation graphics editor. In addition to reformatting, the transfer program applied the following modifications to the data:

Dissolved oxygen was converted from ml/l to M by multiplying the values by 44.66.

The raw transmissometer voltages were corrected for light source decay using a correction ratio computed from light readings in air taken during the cruise and the manufacturer's figure for the new instrument (4.802 V). The correction was applied as follows:

Cruise From To Air Reading (V)
D210 27/08/94 18:05 29/08/94 01:46 4.770
29/08/94 01:46 30/08/94 03:39 4.773
30/08/94 03:40 01/09/94 04:24 4.763
01/09/94 04:25 02/09/94 00:09 4.761
02/09/94 00:10 04/09/94 06:21 4.758
04/09/94 06:22 06/09/94 08:48 4.763
06/09/94 08:49 11/09/94 06:54 4.758
11/09/94 06:55 14/09/94 11:28 4.766
14/09/94 11:29 27/09/94 07:21 4.758
27/09/94 07:22 30/09/94 09:23 4.761
D212 16/11/94 12:56 15/12/94 11:40 4.763

Transmissometer voltages were converted to percentage transmission by multiplying them by 20 and attenuance computed using algorithm:

  • attenuance = 4 ln (percent transmittance / 100)

Editing

Using a custom in-house graphics editor, the downcasts and upcasts were differentiated and the limits of the downcasts were manually flagged. Spikes on any of the downcast channels were manually flagged 'suspect' by modification of the associated quality control flag. An instrument spike was defined as a single value or small number of values which showed an inexplicable variation of more than the recommended target precision for that particular parameter. 'Flagging' involved setting a single character quality control flag to denote the status of the data; in this way none of the original data values were edited or deleted during quality control. The following quality control flags were used:

  • G - good data
  • S - suspect data (instrument spike or malfunction)
  • N - null data (not measured)

The pressure ranges over which the bottle samples were taken were logged by manual interaction with the editor. Usually, the marked reaction of the oxygen sensor to the bottle firing sequence was used to determine this. These pressure ranges were subsequently used, in conjunction with a geometrical correction for the position of the water bottles with respect to the CTD pressure transducer, to determine the pressure range of data to be averaged for calibration purposes.

Once screened, the CTD downcasts were loaded into a database under the Oracle relational database management system and further edited as follows:

  • on all deep (>300 metres) casts, the upwelling and downwelling PAR channels were all set to suspect as the light meters were taken off for deep casts.

Calibration

Calibration procedures involved comparing the raw output against discrete calibration samples taken concurrently. Particular care was taken to ensure maximum temporal coverage of calibration samples, in order that any time-dependent instrument drift could be fully corrected. Errant calibration points were rejected only if sampling occurred over a considerable gradient and there was reasonable doubt whether the CTD was sampling the same water as the discrete calibration sample. Simple linear regression or multiple linear regression was used to establish the calibration algorithms, apart from in the case of the Aquatrakka fluorometer where the voltage was regressed against log-transformed chlorophyll concentrations. All calibrations described here have been applied to the data.

Pressure

The pressure offset was determined by looking at the pressures recorded when the CTD was clearly logging in air (readily apparent from the conductivity channel). A mean air value (standard deviation of 0.3 db) was determined for all the data from cruise D210, giving the correction:

  • Pcorrected = Pobserved - 0.82 db

For cruise D212, two different pressure corrections were used (standard deviations of 0.29 and 0.27db respectively) as follows:

  • Pcorr = Pobs - 0.25 db - for casts A1(6,9,16,18,22), A2(6), A7(27), GOM2(3)
  • Pcorr = Pobs - 0.35 db - for all other casts

Temperature

The CTD temperatures were in excellent agreement with the digital reversing thermometer readings. Hence no temperature calibration has been applied.

Salinity

Salinity was calibrated against 173 water bottle samples measured on the Guildline 55358 Autolab Salinometer during the two cruises. Samples were obtained from 172 of the 289 casts, usually at the maximum depth of the cast.

Samples were collected in glass bottles filled to just below the neck and sealed with plastic stoppers. Batches of samples were left for at least 24 hours to reach thermal equilibrium in the constant temperature laboratory containing the salinometer before analysis. The corrections applied were:

  • Scorrected = Sobserved + 0.0116 (s d = 0.02) - for cruise D210
  • Scorrected = Sobserved + 0.03555 (s d= 0.021) - for cruise D212

Oxygen

The dissolved oxygen sensor was calibrated against 1032 water bottle samples analysed following the Winkler titration procedures outlined in Carpenter (1965). The samples were taken from 86 of the 289 casts, normally at several depths. The probe was stable throughout the cruise and therefore a single calibration has been applied to each cruise:

  • Ocorrected = Oraw * 2.18 + 1.38 (R2 = 95.2%: n=533)
  • Ocorrected = Oraw * 2.82 - 1.04 (R2 = 96.7%: n=499)

Oxygen saturation present in the data files was computed using the algorithm presented in Benson and Krause (1984).

Chlorophyll

Chlorophyll was measured with a Chelsea Mk2 Aquatrakka fluorometer calibrated against discrete samples taken from 654 shallow (< 300 metres) CTD bottles. Samples were filtered through Whatman GF/F filters and frozen in liquid nitrogen until analysed onboard. The frozen filters were extracted in 2-5 ml of 90% acetone and aliquot injected onto a C-8 reverse phase column.Analysis was carried out by reverse phase HPLC. The resultant concentrations of chlorophyll and diavinyl chlorophyll a were summed to give a total calibration concentration. The resulting calibration equations are:

  • chlorophyll (mg/m3) = exp (-1.75 + 0.794 * raw-voltage) (R2 = 54.8%)
  • chlorophyll (mg/m3) = exp (-3.12 + 1.73 * raw-voltage) (R2 = 65.35%)

In both cases, no significant quenching effects were observed; therefore there is no light term in either calibration.

Data Reduction

Once all screening and calibration procedures were completed, the data set was binnedto 2 db (casts deeper than 100 db) or 1 db (casts shallower than 100 db). The binningalgorithm excluded any data points flagged suspect and attempted linear interpolationover gaps up to 3 bins wide. If any gaps larger than this were encountered, the data in thegaps were set null.Downcast values corresponding to the bottle firing depths were incorporated into thedatabase. Oxygen saturations have been computed using the algorithm of Benson and Krause (1984).


Project Information

ARABESQUE

ARABESQUE was a multidisciplinary oceanographic research project focused on the Arabian Sea and Northwest Indian Ocean during the monsoon and intermonsoon season in 1994. Funding for ARABESQUE was provided by the Ministry of Defence/ Defence Research Agency Joint Grant TQ/10/3/2 and Amersham International as well as the Natural Environment Research Council. ARABESQUE was almost entirely field based with extensive physical, chemical and biological measurements made in the Gulf of Oman, the Arabian Sea and the Northwest Indian Ocean. The aim of the project was to study the upper ocean microbial biogeochemistry in the Arabian Sea. Its focus was carbon and nitrogen cycling processes linked to climate change. The project was a UK contribution to the Joint Global Ocean Flux Study (JGOFS) Process Studies of the Arabian Sea. ARABESQUE was organised by Plymouth Marine Laboratory (PML).

Objectives

The detailed scientific objectives of ARABESQUE were to quantify the seasonal influence of the Monsoon winds in the Arabian Sea on:

  • Upwelling of nutrients and the resultant production and fate of phytoplankton, in terms of size-fractionated, new and regenerated production

  • Vertical and on-shelf gradients of heterotrophic, methanogenic and denitrifying bacteria

  • Distribution of chemotaxonomic pigments with links to optical properties of seawater

  • The Dissolved Inorganic and Organic Carbon cycle

  • Air-sea exchange of Sulphur and Nitrogen biogases including dimethyl sulphide, methylamines and methane

  • Sedimentation rates and the fate of organic matter through the oxygen depleted zone

A final objective was to calibrate satellite data on ocean colour so as to map the biogeochemistry of the northwestern Indian Ocean.

Fieldwork

The fieldwork programme consisted of two cruises of RRS Discovery. Cruise 210 (from 27 August to 4 October 1994) was timed to coincide with the South West Monsoon. Cruise 212 (from 16 November to 19 December 1994) took place during the intermonsoon period through to the onset of the North East Monsoon. The fieldwork programme included three repeated sections;

  • One section along the Gulf of Oman

  • A section at 8°N 67°E to 14° 30N 67°E

  • A major section from 8°N 67°E to the coast of Oman

Other one-off sections were also crossed in the area. Sections were covered by underway upper ocean measurements and by a total of 21 sites where CTD/water-bottle stations were taken, 14 of which were repeated.

Data Management

Data management services to the ARABESQUE project were provided by the British Oceanographic Data Centre, funded by the UK Natural Environment Research Council.


Data Activity or Cruise Information

Cruise

Cruise Name D210
Departure Date 1994-08-25
Arrival Date 1994-10-05
Principal Scientist(s)R Fauzi C Mantoura (Plymouth Marine Laboratory)
Ship RRS Discovery

Complete Cruise Metadata Report is available here


Fixed Station Information


No Fixed Station Information held for the Series


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain
B nominal value
Q value below limit of quantification