Metadata Report for BODC Series Reference Number 1077817

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

Data Access Policy

GEOTRACES - data access conditions

Access to this data is currently restricted and it is not available via BODC's normal delivery mechanisms.

GEOTRACES data are published via the GEOTRACES IDP, available at:

• IDP 2021v2

Narrative Documents

Sea-Bird Dissolved Oxygen Sensor SBE 43 and SBE 43F

The SBE 43 is a dissolved oxygen sensor designed for marine applications. It incorporates a high-performance Clark polarographic membrane with a pump that continuously plumbs water through it, preventing algal growth and the development of anoxic conditions when the sensor is taking measurements.

Two configurations are available: SBE 43 produces a voltage output and can be incorporated with any Sea-Bird CTD that accepts input from a 0-5 volt auxiliary sensor, while the SBE 43F produces a frequency output and can be integrated with an SBE 52-MP (Moored Profiler CTD) or used for OEM applications. The specifications below are common to both.

Specifications

Further details can be found in the manufacturer's specification sheet.

NBP0901 CTD Instrumentation

CTD Unit and Auxiliary Sensors

The CTD unit was a Sea-Bird 9/11 plus with a Sea-Bird 32 Carousel 24 Position Pylon (s/n 33211265-0066). The sensors and pumps were mounted vertically on a horizontal frame connected to the rosette frame near the bottom. A single pressure sensor, rated to 6,000 dbar (10,000 psia), provided pressure information for conversion to depth. Additionally sensors were attached to the rosette in support of the DynaLife project. This CTD suite was run in real time at 24Hz using an 11 plus deck unit (s/n 11P19858-0768).

CTD casts were typically made to within 10 m of the bottom using both a Benthos PSA-916 altimeter and a SBE bottom contact with a 10 m line to determine distance off the seafloor. Exceptions are casts 1 and 2, which only went to 2000 m in much deeper water, cast 159, which went to 1200 m in 4500 m water, and yo-yo casts 63-81. The CTD was lowered at 20 m/minute from the surface to 50 m, 30 m/minute from 50 m to 100 m, and 50 m/minute below 100 m. It was raised at 50-60 m/minute.

The table below lists detailed information about the various sensors.

Change of sensors during cruise: The primary dissolved oxygen sensor was switched after cast 23, when it was determined to have high frequency noise and an offset from the calibration samples taken with the rosette. Additionally, a different primary dissolved oxygen sensor was used for cast 104 due to serial number confusion.

Sea-Bird Electronics SBE 911 and SBE 917 series CTD profilers

The SBE 911 and SBE 917 series of conductivity-temperature-depth (CTD) units are used to collect hydrographic profiles, including temperature, conductivity and pressure as standard. Each profiler consists of an underwater unit and deck unit or SEARAM. Auxiliary sensors, such as fluorometers, dissolved oxygen sensors and transmissometers, and carousel water samplers are commonly added to the underwater unit.

Underwater unit

The CTD underwater unit (SBE 9 or SBE 9 plus) comprises a protective cage (usually with a carousel water sampler), including a main pressure housing containing power supplies, acquisition electronics, telemetry circuitry, and a suite of modular sensors. The original SBE 9 incorporated Sea-Bird's standard modular SBE 3 temperature sensor and SBE 4 conductivity sensor, and a Paroscientific Digiquartz pressure sensor. The conductivity cell was connected to a pump-fed plastic tubing circuit that could include auxiliary sensors. Each SBE 9 unit was custom built to individual specification. The SBE 9 was replaced in 1997 by an off-the-shelf version, termed the SBE 9 plus, that incorporated the SBE 3 plus (or SBE 3P) temperature sensor, SBE 4C conductivity sensor and a Paroscientific Digiquartz pressure sensor. Sensors could be connected to a pump-fed plastic tubing circuit or stand-alone.

Temperature, conductivity and pressure sensors

The conductivity, temperature, and pressure sensors supplied with Sea-Bird CTD systems have outputs in the form of variable frequencies, which are measured using high-speed parallel counters. The resulting count totals are converted to numeric representations of the original frequencies, which bear a direct relationship to temperature, conductivity or pressure. Sampling frequencies for these sensors are typically set at 24 Hz.

The temperature sensing element is a glass-coated thermistor bead, pressure-protected inside a stainless steel tube, while the conductivity sensing element is a cylindrical, flow-through, borosilicate glass cell with three internal platinum electrodes. Thermistor resistance or conductivity cell resistance, respectively, is the controlling element in an optimized Wien Bridge oscillator circuit, which produces a frequency output that can be converted to a temperature or conductivity reading. These sensors are available with depth ratings of 6800 m (aluminium housing) or 10500 m (titanium housing). The Paroscientific Digiquartz pressure sensor comprises a quartz crystal resonator that responds to pressure-induced stress, and temperature is measured for thermal compensation of the calculated pressure.

Additional sensors

Optional sensors for dissolved oxygen, pH, light transmission, fluorescence and others do not require the very high levels of resolution needed in the primary CTD channels, nor do these sensors generally offer variable frequency outputs. Accordingly, signals from the auxiliary sensors are acquired using a conventional voltage-input multiplexed A/D converter (optional). Some Sea-Bird CTDs use a strain gauge pressure sensor (Senso-Metrics) in which case their pressure output data is in the same form as that from the auxiliary sensors as described above.

Deck unit or SEARAM

Each underwater unit is connected to a power supply and data logging system: the SBE 11 (or SBE 11 plus) deck unit allows real-time interfacing between the deck and the underwater unit via a conductive wire, while the submersible SBE 17 (or SBE 17 plus) SEARAM plugs directly into the underwater unit and data are downloaded on recovery of the CTD. The combination of SBE 9 and SBE 17 or SBE 11 are termed SBE 917 or SBE 911, respectively, while the combinations of SBE 9 plus and SBE 17 plus or SBE 11 plus are termed SBE 917 plus or SBE 911 plus.

Specifications

Specifications for the SBE 9 plus underwater unit are listed below:

Further details can be found in the manufacturer's specification sheet.

WETLabs C-Star transmissometer

This instrument is designed to measure beam transmittance by submersion or with an optional flow tube for pumped applications. It can be used in profiles, moorings or as part of an underway system.

Two models are available, a 25 cm pathlength, which can be built in aluminum or co-polymer, and a 10 cm pathlength with a plastic housing. Both have an analog output, but a digital model is also available.

This instrument has been updated to provide a high resolution RS232 data output, while maintaining the same design and characteristics.

Specifications

Further details are available in the manufacturer's specification sheet or user guide.

CTD data for Cruise NBP0901 (GPpr03)

Sampling Strategy

A total of 160 CTD casts were carried out during cruise NBP0901, on board the Nathaniel B. Palmer, using a stainless steel CTD frame equipped with 24 10 L "Bullister" niskin bottles. The cruise surveyed GEOTRACES section GPpr03.

Originator's Data Processing Procedures

Processing was performed immediately upon completion of the CTD using Sea-Birds SeaSave software version 7.14. The software was integrated with the Palmer's NEMA 1 Hz GPS to provide a position for each CTD scan. Random spikes occurred in the data throughout the cruise, particularly in pressure, temperature and conductivity. These spikes were removed in processing using wild edit. Plots of the processed potential temperature, salinity, dissolved oxygen, and density were generated for each cast and used to identify spiking.

Oxygen

A total of 407 oxygen samples were collected for Winkler titration from 126 CTD stations in order to calibrate the oxygen sensors. After calibration, the data from the secondary sensor were deemed to be more reliable.

Salinity

A total of 506 salinity samples were analyzed during the cruise using a Autosal salinometer (SN 61-670). These samples were used to calibrate the conductivity sensors.

NBP0901 Cruise report

Further information can be found in the NBP0901 Cruise report.

BODC Data Processing Procedures

Data received were converted to the BODC internal format (a netCDF subset) and then mapped to GEOTRACES parameter names. A parameter mapping table is provided below:

Following transfer the data were screened using BODC in-house visualisation software. Suspect data values were assigned the appropriate BODC data quality flag. Missing data values, where present, were changed to the missing data value and assigned a BODC data quality flag. These flags are provided in the IDP as SeaDataNet flags.

Project Information

GEOTRACES

Introduction

GEOTRACES is an international programme sponsored by SCOR which aims to improve our understanding of biogeochemical cycles and large-scale distribution of trace elements and their isotopes (TEIs) in the marine environment. The global field programme started in 2009 and will run for at least a decade. Before the official launch of GEOTRACES, fieldwork was carried out as part of the International Polar Year (IPY)(2007-2009) where 14 cruises were connected to GEOTRACES.

GEOTRACES is expected to become the largest programme to focus on the chemistry of the oceans and will improve our understanding of past, present and future distributions of TEIs and their relationships to important global processes.

This initiative was prompted by the increasing recognition that TEIs are playing a crucial role as regulators and recorders of important biogeochemical and physical processes that control the structure and productivity of marine ecosystems, the dispersion of contaminants in the marine environment, the level of greenhouse gases in the atmosphere, and global climate.

Scientific Objectives

GEOTRACES mission is: To identify processes and quantify fluxes that control the distribution of key trace elements and isotopes in the ocean, and to establish the sensitivity of these distributions to changing environmental conditions.

Three overriding goals support the GEOTRACES mission

• Determine ocean distributions of selected TEIs at all major ocean basins
• Evaluate the sources, sinks, and internal cycling of these TEIs and thereby characterize more completely their global biogeochemical cycles
• Provide a baseline distribution in the Polar Regions as reference for assessing past and future changes.

These goals will be pursued through complementary research strategies, including observations, experiments and modelling.

Fieldwork

The central component of GEOTRACES fieldwork will be a series of cruises spanning all Ocean basins see map below.

Three types of cruise are required to meet the goals set out by GEOTRACES. These are

• Section cruises - These will measure all the key parameters (see below) over the full depth of the water column. The sections were discussed and approved by the International GEOTRACES Scientific Steering Committee at the basin workshops.
• Process Studies - These will investigate a particular process relevant to the cycling of trace metal and isotopes. They must follow the "Criteria for Establishing GEOTRACES Process Studies" and be approved by the International GEOTRACES Scientific Steering Committee.
• Cruises collecting GEOTRACES compliant data - These will collect some trace element or isotope data. They must follow the GEOTRACES Intercalibration and Data Management protocols

IPY-GEOTRACES

The IPY-GEOTRACES programme comprised of 14 research cruises on ships from 7 nations; Australia, Canada, France, Germany, New Zealand, Japan and Russia. The cruises will not be classified in the same way as the full GEOTRACES programme since the intercalibration protocols and data management protocols had not been established before the start of the IPY. But IPY-GEOTRACES data will still be quality controlled by GDAC and in the majority of cases verified versus Intercalibration standards or protocols.

Key parameters

The key parameters as set out by the GEOTRACES science plan are as follows: Fe, Al, Zn, Mn, Cd, Cu; 15N, 13C; 230Th, 231Pa; Pb isotopes, Nd isotopes; stored sample, particles, aerosols.

Weblink:

http://www.bodc.ac.uk/geotraces/
http://www.geotraces.org/

Data Activity or Cruise Information

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

No Fixed Station Information held for the Series

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle: