Search the data

Metadata Report for BODC Series Reference Number 589482


Metadata Summary

Data Description

Data Category CTD or STD cast
Instrument Type
NameCategories
Sea-Bird SBE 911plus CTD  CTD; water temperature sensor; salinity sensor
Instrument Mounting research vessel
Originating Country Norway
Originator -
Originating Organization Institute of Marine Research, Norway
Processing Status banked
Online delivery of data Download available - Ocean Data View (ODV) format
Project(s) MAIA
 

Data Identifiers

Originator's Identifier JH2001/0635
BODC Series Reference 589482
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 2001-08-23 08:24
End Time (yyyy-mm-dd hh:mm) -
Nominal Cycle Interval -
 

Spatial Co-ordinates

Latitude 73.25100 N ( 73° 15.1' N )
Longitude 19.39970 E ( 19° 24.0' E )
Positional Uncertainty Unspecified
Minimum Sensor or Sampling Depth 2.97 m
Maximum Sensor or Sampling Depth 435.0 m
Minimum Sensor or Sampling Height 14.0 m
Maximum Sensor or Sampling Height 446.03 m
Sea Floor Depth 449.0 m
Sea Floor Depth Source -
Sensor or Sampling Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor or Sampling Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
 

Parameters

BODC CODERankUnitsTitle
CNDCST011Siemens per metreElectrical conductivity of the water body by CTD
PRESPR011DecibarsPressure (spatial coordinate) exerted by the water body by profiling pressure sensor and correction to read zero at sea level
PSALST011DimensionlessPractical salinity of the water body by CTD and computation using UNESCO 1983 algorithm
TEMPST011Degrees CelsiusTemperature of the water body by CTD or STD

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database


Data Access Policy

Public domain data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

The recommended acknowledgment is

"This study uses data from the data source/organisation/programme, provided by the British Oceanographic Data Centre and funded by the funding body."


Narrative Documents

Sea-Bird Electronics SBE 911 and SBE 917 series CTD profilers

The SBE 911 and SBE 917 series of conductivity-temperature-depth (CTD) units are used to collect hydrographic profiles, including temperature, conductivity and pressure as standard. Each profiler consists of an underwater unit and deck unit or SEARAM. Auxiliary sensors, such as fluorometers, dissolved oxygen sensors and transmissometers, and carousel water samplers are commonly added to the underwater unit.

Underwater unit

The CTD underwater unit (SBE 9 or SBE 9 plus) comprises a protective cage (usually with a carousel water sampler), including a main pressure housing containing power supplies, acquisition electronics, telemetry circuitry, and a suite of modular sensors. The original SBE 9 incorporated Sea-Bird's standard modular SBE 3 temperature sensor and SBE 4 conductivity sensor, and a Paroscientific Digiquartz pressure sensor. The conductivity cell was connected to a pump-fed plastic tubing circuit that could include auxiliary sensors. Each SBE 9 unit was custom built to individual specification. The SBE 9 was replaced in 1997 by an off-the-shelf version, termed the SBE 9 plus, that incorporated the SBE 3 plus (or SBE 3P) temperature sensor, SBE 4C conductivity sensor and a Paroscientific Digiquartz pressure sensor. Sensors could be connected to a pump-fed plastic tubing circuit or stand-alone.

Temperature, conductivity and pressure sensors

The conductivity, temperature, and pressure sensors supplied with Sea-Bird CTD systems have outputs in the form of variable frequencies, which are measured using high-speed parallel counters. The resulting count totals are converted to numeric representations of the original frequencies, which bear a direct relationship to temperature, conductivity or pressure. Sampling frequencies for these sensors are typically set at 24 Hz.

The temperature sensing element is a glass-coated thermistor bead, pressure-protected inside a stainless steel tube, while the conductivity sensing element is a cylindrical, flow-through, borosilicate glass cell with three internal platinum electrodes. Thermistor resistance or conductivity cell resistance, respectively, is the controlling element in an optimized Wien Bridge oscillator circuit, which produces a frequency output that can be converted to a temperature or conductivity reading. These sensors are available with depth ratings of 6800 m (aluminium housing) or 10500 m (titanium housing). The Paroscientific Digiquartz pressure sensor comprises a quartz crystal resonator that responds to pressure-induced stress, and temperature is measured for thermal compensation of the calculated pressure.

Additional sensors

Optional sensors for dissolved oxygen, pH, light transmission, fluorescence and others do not require the very high levels of resolution needed in the primary CTD channels, nor do these sensors generally offer variable frequency outputs. Accordingly, signals from the auxiliary sensors are acquired using a conventional voltage-input multiplexed A/D converter (optional). Some Sea-Bird CTDs use a strain gauge pressure sensor (Senso-Metrics) in which case their pressure output data is in the same form as that from the auxiliary sensors as described above.

Deck unit or SEARAM

Each underwater unit is connected to a power supply and data logging system: the SBE 11 (or SBE 11 plus) deck unit allows real-time interfacing between the deck and the underwater unit via a conductive wire, while the submersible SBE 17 (or SBE 17 plus) SEARAM plugs directly into the underwater unit and data are downloaded on recovery of the CTD. The combination of SBE 9 and SBE 17 or SBE 11 are termed SBE 917 or SBE 911, respectively, while the combinations of SBE 9 plus and SBE 17 plus or SBE 11 plus are termed SBE 917 plus or SBE 911 plus.

Specifications

Specifications for the SBE 9 plus underwater unit are listed below:

Parameter Range Initial accuracy Resolution at 24 Hz Response time
Temperature -5 to 35°C 0.001°C 0.0002°C 0.065 sec
Conductivity 0 to 7 S m-1 0.0003 S m-1 0.00004 S m-1 0.065 sec (pumped)
Pressure 0 to full scale (1400, 2000, 4200, 6800 or 10500 m) 0.015% of full scale 0.001% of full scale 0.015 sec

Further details can be found in the manufacturer's specification sheet.

Johan Hjort 10 / 2001 CTD Processing Document

The CTD data were processed by the Institute of Marine Research, Bergen.

A Seabird 911 plus was used to sample the CTD data. The data were low pass filtered and averaged into 1 db bins using the Seabird SEASOFT software.

All data were then manually checked for obvious incorrect values and density instabilities, these were either replaced or marked as dubious.

The salinity / conductivity data were corrected using water samples taken on each cruise.

Section Period Station Numbers Conductivity Calibration
Fugloya_Bjornoya Aug 2001 0620 - 0641 Obs+(-0.002055+(1.9753E-6)*P)
Where P is the pressure in dbar.

The data were also visually inspected by BODC.

Additional Meteorological Station Data

CTD Wdir Wspeed Dtemp Weather Clouds Sea Ice
JH2001/0620 7 23 8.8 4 8 2 0
JH2001/0621 7 18 8.6 0 0 4 0
JH2001/0622 7 12 8.1 0 0 3 0
JH2001/0623 7 12 8.7 0 0 3 0
JH2001/0625 8 24 8.9 0 0 4 0
JH2001/0626 8 11 8.9 0 2 4 0
JH2001/0627 7 20 8.6 0 2 3 0
JH2001/0628 8 14 8.5 0 2 3 0
JH2001/0629 10 7 8.7 0 2 3 0
JH2001/0630 10 8 8.4 2 8 3 0
JH2001/0631 4 3 8.4 2 8 3 0
JH2001/0632 2 3 7.6 2 8 3 0
JH2001/0633 19 7 7.1 2 5 2 0
JH2001/0635 3 4 5.4 2 8 1 0
JH2001/0636 35 2 6.3 2 8 1 0
JH2001/0637 35 2 5.3 2 8 1 0
JH2001/0638 10 2 5.0 2 8 1 0
JH2001/0639 6 2 4.6 2 8 1 0
JH2001/0640 11 2 3.1 2 8 3 0
JH2001/0641 28 2 3.5 2 8 3 0

Where:

  • Wdir = Wind direction, WMO Code 0877
  • Wspeed = Wind speed, Knots
  • Dtemp = Dry bulb temperature, Deg C
  • Weather (WMO code 4561)
  • Clouds (WMO code 2700)
  • Sea (WMO code 3700)
  • Ice (No ice)

Project Information

Monitoring the Atlantic Inflow toward the Arctic (MAIA)

Introduction

MAIA is an EU Fifth Framework Programme supporting Key Action 2 (Global Change, Climate and Biodiversity) of Theme 4: Energy, Environment and Sustainable Development. The overall objective of MAIA is to develop an inexpensive and reliable system based on coastal sea level data for monitoring the inflows of Atlantic water into the northern seas.

Scientific Rationale

The flux of Atlantic Water to the northern seas is vital for the existence of life in northern Europe. More than half of the Atlantic Water appears to enter the Norwegian Sea to the west of the Faroe Islands. A lesser, warmer amount enters along the continental margin past Scotland. There have been several attempts to estimate and monitor these fluxes and see how the ice extent in the north is correlated to them.

The special goals of MAIA are:

  • to monitor the inflow of salt and heat to the northern seas for the analysis of climate variability, distinguishing between warmer (eastern) and cooler (western) inflow past the Faroes, and the major routes through the Barents Sea, with a time resolution better than a week, a spatial resolution of the major routes and an accuracy better than 15%.

  • to understand the causes of errors and recommend strategies to improve the future accuracy of such a monitoring tool.

Project Components

The project was divided into 3 phases:

  • Phase I

    Phase I was to analyse historical observations of sea-level fluctuations during the past decade and compare them with available bottom pressure and in situ current velocity measurements in the region of interest.

  • Phase II

    Phase II is a dedicated validation study in the Shetland- Iceland region and in the Barents Sea to verify that the system can give the required results to the desired accuracy and resolution. The validation period was from summer 2000 to November 2001.

  • Phase III

    Phase III of the project includes evaluating the validations, the effects of external influences and the ice studies, and making recommendations for future monitoring.


Data Activity or Cruise Information

Cruise

Cruise Name JH10/01
Departure Date 2001-08-20
Arrival Date 2001-09-09
Principal Scientist(s)Hildegunn Græsdal (Institute of Marine Research, Norway), Petter Fossum (Institute of Marine Research, Norway)
Ship RV Johan Hjort

Complete Cruise Metadata Report is available here


Fixed Station Information


No Fixed Station Information held for the Series


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain
B nominal value
Q value below limit of quantification