Search the data

Metadata Report for BODC Series Reference Number 771832


Metadata Summary

Data Description

Data Category CTD or STD cast
Instrument Type
NameCategories
Sea-Bird SBE 43 Dissolved Oxygen Sensor  dissolved gas sensors
Chelsea Technologies Group Aquatracka fluorometer  fluorometers
Chelsea Technologies Group 2-pi PAR irradiance sensor  radiometers
Sea-Bird SBE 911plus CTD  CTD; water temperature sensor; salinity sensor
Chelsea Technologies Group Alphatracka transmissometer  transmissometers
Benthos PSA-916T Sonar Altimeter  altimeters
Instrument Mounting lowered unmanned submersible
Originating Country United Kingdom
Originator Dr Adrian Martin
Originating Organization National Oceanography Centre, Southampton
Processing Status banked
Online delivery of data Download available - Ocean Data View (ODV) format
Project(s) Oceans 2025
Oceans 2025 Theme 2
Oceans 2025 Theme 2 WP2.5
 

Data Identifiers

Originator's Identifier CTA16247
BODC Series Reference 771832
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 2007-08-09 22:29
End Time (yyyy-mm-dd hh:mm) 2007-08-09 22:48
Nominal Cycle Interval 2.0 decibars
 

Spatial Co-ordinates

Latitude 59.99910 N ( 59° 59.9' N )
Longitude 20.45690 W ( 20° 27.4' W )
Positional Uncertainty Unspecified
Minimum Sensor or Sampling Depth 4.95 m
Maximum Sensor or Sampling Depth 801.8 m
Minimum Sensor or Sampling Height 1957.33 m
Maximum Sensor or Sampling Height 2754.18 m
Sea Floor Depth 2759.13 m
Sea Floor Depth Source GEBCO1901
Sensor or Sampling Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor or Sampling Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Chart reference - Depth extracted from available chart
 

Parameters

BODC CODERankUnitsTitle
ACYCAA011DimensionlessSequence number
AHSFZZ011MetresHeight (spatial coordinate) relative to bed surface in the water body
CNDCST011Siemens per metreElectrical conductivity of the water body by CTD
CNDCST021Siemens per metreElectrical conductivity of the water body by CTD (sensor 2)
CPHLPM011Milligrams per cubic metreConcentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer and manufacturer's calibration applied
DOXYSC011Micromoles per litreConcentration of oxygen {O2 CAS 7782-44-7} per unit volume of the water body [dissolved plus reactive particulate phase] by Sea-Bird SBE 43 sensor and calibration against sample data
DWIRPP011Watts per square metreDownwelling 2-pi scalar irradiance as energy of electromagnetic radiation (PAR wavelengths) in the water body by 2-pi scalar radiometer
OXYSSC011PercentSaturation of oxygen {O2 CAS 7782-44-7} in the water body [dissolved plus reactive particulate phase] by Sea-Bird SBE 43 sensor and calibration against sample data and computation from concentration using Benson and Krause algorithm
POPTDR011PercentTransmittance (red light wavelength) per 25cm of the water body by 25cm path length red light transmissometer
PRESPR011DecibarsPressure (spatial coordinate) exerted by the water body by profiling pressure sensor and correction to read zero at sea level
PSALCC011DimensionlessPractical salinity of the water body by CTD and computation using UNESCO 1983 algorithm and calibration against independent measurements
PSALCC021DimensionlessPractical salinity of the water body by CTD (second sensor) and computation using UNESCO 1983 algorithm and calibration against independent measurements
SIGTPR011Kilograms per cubic metreSigma-theta of the water body by CTD and computation from salinity and potential temperature using UNESCO algorithm
SIGTPR021Kilograms per cubic metreSigma-theta of the water body by CTD (second sensor) and computation from salinity and potential temperature using UNESCO algorithm
TEMPS9011Degrees CelsiusTemperature (ITS-90) of the water body by CTD or STD
TEMPS9021Degrees CelsiusTemperature (ITS-90) of the water body by CTD or STD (second sensor)
TOKGPR011Litres per kilogramConversion factor (volume to mass) for the water body by CTD and computation of density (in-situ potential temperature surface pressure) reciprocal from pressure, temperature and salinity

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database

Data Quality Report

The quality of measurements obtained with the Satlantic ISUS UV in-situ nitrate sensor were considered highly unreliable by the data originators and it was suggested that these data should be dropped from the series. It was confirmed that these data were questionable following in-house screening at BODC. Since the data were not fit for future purpose the channel was deleted from the series.


Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."


Narrative Documents

Sea-Bird Dissolved Oxygen Sensor SBE 43 and SBE 43F

The SBE 43 is a dissolved oxygen sensor designed for marine applications. It incorporates a high-performance Clark polarographic membrane with a pump that continuously plumbs water through it, preventing algal growth and the development of anoxic conditions when the sensor is taking measurements.

Two configurations are available: SBE 43 produces a voltage output and can be incorporated with any Sea-Bird CTD that accepts input from a 0-5 volt auxiliary sensor, while the SBE 43F produces a frequency output and can be integrated with an SBE 52-MP (Moored Profiler CTD) or used for OEM applications. The specifications below are common to both.

Specifications

Housing Plastic or titanium
Membrane

0.5 mil- fast response, typical for profile applications

1 mil- slower response, typical for moored applications

Depth rating

600 m (plastic) or 7000 m (titanium)

10500 m titanium housing available on request

Measurement range 120% of surface saturation
Initial accuracy 2% of saturation
Typical stability 0.5% per 1000 h

Further details can be found in the manufacturer's specification sheet.

Benthos Programmable Sonar Altimeter (PSA) 916 and 916T

The PSA 916 is a submersible altimeter that uses the travel time of an acoustic signal to determine the distance of the instrument from a target surface. It provides the user with high resolution altitude or range data while simultaneously outputting data through a digital serial port. A wide beam angle provides for reliable and accurate range measurements under the most severe operational conditions. The instrument is electronically isolated to eliminate any potential signal interference with host instrument sensors. The PSA 916 is an upgrade of the PSA 900.

The standard model (PSA 916) has an operational depth range of 0 - 6000 m, while the titanium PSA 916T has a depth range of 0 - 10000 m. All other specifications for the two versions are the same.

Specifications

Transmit frequency 200 kHz
Transmit pulse width 250 µs
Beam pattern 14° conical
Pulse repetition rate

internal selection: 5 pps

external selection: up to 5 pps- user controlled

Range

100 m full scale

1.0 m guaranteed minimum

0.8 m typical

Range

1 cm for RS232 output

2.5 cm for analog output

Operating depth 6000 m (PSA 916) or 10000 m (PSA 916T)

Further details can be found in the manufacturer's specification sheets for the PSA 916 and the PSA 916T.

Instrument Description

CTD Stainless Steel Unit and Auxiliary Sensors

Instrument/Sensor Serial Number Manufacturer's Calibration Date Comments
Sea-Bird 911plus CTD 0636    
Sea-Bird SBE 9plus Digiquartz primary pressure sensor 83008 13 May 2005  
Sea-Bird SBE 3 primary1 temperature sensor 4383 1 May 2007 Vane-mounted
Sea-Bird SBE 3 secondary1 temperature sensor 4782 12 April 2007 CTD-mounted
Sea-Bird SBE 4 primary1 conductivity sensor 2164 1 May 2007 Vane-mounted
Sea-Bird SBE 4 secondary1 conductivity sensor 3258 27 March 2007 CTD-mounted
Sea-Bird SBE 43 oxygen sensor 0619 5 October 2006  
Benthos PSA-916T altimeter 1040 repaired December 2006  
Chelsea Aquatracka Mk III (chlorophyll a) fluorimeter 088095 4 January 2007  
Chelsea Alphatracka Mk II (25cm, 660 nm) transmissometer 161-2642-002 4 September 1996  
2π PML (Chelsea) PAR sensor (down-welling) 09 23 March 2005 removed from casts greater than 1000 m
Satlantic ISUS nitrate sensor 60   removed from casts greater than 1000 m
25 July 2007 (Laboratory calibration)
Sea-Bird SBE 32 carousel 32-37898-0518    
Ocean Test Equipment water bottles (20 L) 32-37898-0518   positions 1-24
RDI Workhorse Monitor 300 kHz ADCP (master) 5415    
RDI Workhorse Monitor 300 kHz ADCP (slave) 9414    

1The primary temperature and conductivity sensor pair (described here) are referred to as secondary sensors in all files produced from Sea-Bird Software processing. The names were swapped during NOCS PSTAR processing where the Sea-Bird named, secondary sensors became the primary sensor pair.

Sea-Bird Electronics SBE 911 and SBE 917 series CTD profilers

The SBE 911 and SBE 917 series of conductivity-temperature-depth (CTD) units are used to collect hydrographic profiles, including temperature, conductivity and pressure as standard. Each profiler consists of an underwater unit and deck unit or SEARAM. Auxiliary sensors, such as fluorometers, dissolved oxygen sensors and transmissometers, and carousel water samplers are commonly added to the underwater unit.

Underwater unit

The CTD underwater unit (SBE 9 or SBE 9 plus) comprises a protective cage (usually with a carousel water sampler), including a main pressure housing containing power supplies, acquisition electronics, telemetry circuitry, and a suite of modular sensors. The original SBE 9 incorporated Sea-Bird's standard modular SBE 3 temperature sensor and SBE 4 conductivity sensor, and a Paroscientific Digiquartz pressure sensor. The conductivity cell was connected to a pump-fed plastic tubing circuit that could include auxiliary sensors. Each SBE 9 unit was custom built to individual specification. The SBE 9 was replaced in 1997 by an off-the-shelf version, termed the SBE 9 plus, that incorporated the SBE 3 plus (or SBE 3P) temperature sensor, SBE 4C conductivity sensor and a Paroscientific Digiquartz pressure sensor. Sensors could be connected to a pump-fed plastic tubing circuit or stand-alone.

Temperature, conductivity and pressure sensors

The conductivity, temperature, and pressure sensors supplied with Sea-Bird CTD systems have outputs in the form of variable frequencies, which are measured using high-speed parallel counters. The resulting count totals are converted to numeric representations of the original frequencies, which bear a direct relationship to temperature, conductivity or pressure. Sampling frequencies for these sensors are typically set at 24 Hz.

The temperature sensing element is a glass-coated thermistor bead, pressure-protected inside a stainless steel tube, while the conductivity sensing element is a cylindrical, flow-through, borosilicate glass cell with three internal platinum electrodes. Thermistor resistance or conductivity cell resistance, respectively, is the controlling element in an optimized Wien Bridge oscillator circuit, which produces a frequency output that can be converted to a temperature or conductivity reading. These sensors are available with depth ratings of 6800 m (aluminium housing) or 10500 m (titanium housing). The Paroscientific Digiquartz pressure sensor comprises a quartz crystal resonator that responds to pressure-induced stress, and temperature is measured for thermal compensation of the calculated pressure.

Additional sensors

Optional sensors for dissolved oxygen, pH, light transmission, fluorescence and others do not require the very high levels of resolution needed in the primary CTD channels, nor do these sensors generally offer variable frequency outputs. Accordingly, signals from the auxiliary sensors are acquired using a conventional voltage-input multiplexed A/D converter (optional). Some Sea-Bird CTDs use a strain gauge pressure sensor (Senso-Metrics) in which case their pressure output data is in the same form as that from the auxiliary sensors as described above.

Deck unit or SEARAM

Each underwater unit is connected to a power supply and data logging system: the SBE 11 (or SBE 11 plus) deck unit allows real-time interfacing between the deck and the underwater unit via a conductive wire, while the submersible SBE 17 (or SBE 17 plus) SEARAM plugs directly into the underwater unit and data are downloaded on recovery of the CTD. The combination of SBE 9 and SBE 17 or SBE 11 are termed SBE 917 or SBE 911, respectively, while the combinations of SBE 9 plus and SBE 17 plus or SBE 11 plus are termed SBE 917 plus or SBE 911 plus.

Specifications

Specifications for the SBE 9 plus underwater unit are listed below:

Parameter Range Initial accuracy Resolution at 24 Hz Response time
Temperature -5 to 35°C 0.001°C 0.0002°C 0.065 sec
Conductivity 0 to 7 S m-1 0.0003 S m-1 0.00004 S m-1 0.065 sec (pumped)
Pressure 0 to full scale (1400, 2000, 4200, 6800 or 10500 m) 0.015% of full scale 0.001% of full scale 0.015 sec

Further details can be found in the manufacturer's specification sheet.

Aquatracka fluorometer

The Chelsea Instruments Aquatracka is a logarithmic response fluorometer. It uses a pulsed (5.5 Hz) xenon light source discharging between 320 and 800 nm through a blue filter with a peak transmission of 420 nm and a bandwidth at half maximum of 100 nm. A red filter with sharp cut off, 10% transmission at 664 nm and 678 nm, is used to pass chlorophyll-a fluorescence to the sample photodiode.

The instrument may be deployed either in a through-flow tank, on a CTD frame or moored with a data logging package.

Further details can be found in the manufacturer's specification sheet.

Chelsea Technologies Group ALPHAtracka and ALPHAtracka II transmissometers

The Chelsea Technologies Group ALPHAtracka (the Mark I) and its successor, the ALPHAtracka II (the Mark II), are both accurate (< 0.3 % fullscale) transmissometers that measure the beam attenuation coefficient at 660 nm. Green (565 nm), yellow (590 nm) and blue (470 nm) wavelength variants are available on special order.

The instrument consists of a Transmitter/Reference Assembly and a Detector Assembly aligned and spaced apart by an open support frame. The housing and frame are both manufactured in titanium and are pressure rated to 6000 m depth.

The Transmitter/Reference housing is sealed by an end cap. Inside the housing an LED light source emits a collimated beam through a sealed window. The Detector housing is also sealed by an end cap. A signal photodiode is placed behind a sealed window to receive the collimated beam from the Transmitter.

The primary difference between the ALPHAtracka and ALPHAtracka II is that the Alphatracka II is implemented with surface-mount technology; this has enabled a much smaller diameter pressure housing to be used while retaining exactly the same optical train as in the Mark I. Data from the Mark II version are thus fully compatible with that already obtained with the Mark I. The performance of the Mark II is further enhanced by two electronic developments from Chelsea Technologies Group - firstly, all items are locked in a signal nulling loop of near infinite gain and, secondly, the signal output linearity is inherently defined by digital circuitry only.

Among other advantages noted above, these features ensure that the optical intensity of the Mark II, indicated by the output voltage, is accurately represented by a straight line interpolation between a reading near full-scale under known conditions and a zero reading when blanked off.

For optimum measurements in a wide range of environmental conditions, the Mark I and Mark II are available in 5 cm, 10 cm and 25 cm path length versions. Output is default factory set to 2.5 volts but can be adjusted to 5 volts on request.

Further details about the Mark II instrument are available from the Chelsea Technologies Group ALPHAtrackaII specification sheet.

Chelsea Technologies Photosynthetically Active Radiation (PAR) Irradiance Sensor

This sensor was originally designed to assist the study of marine photosynthesis. With the use of logarithmic amplication, the sensor covers a range of 6 orders of magnitude, which avoids setting up the sensor range for the expected signal level for different ambient conditions.

The sensor consists of a hollow PTFE 2-pi collector supported by a clear acetal dome diverting light to a filter and photodiode from which a cosine response is obtained. The sensor can be used in moorings, profiling or deployed in towed vehicles and can measure both upwelling and downwelling light.

Specifications

Operation depth 1000 m
Range 2000 to 0.002 µE m-2 s-1
Angular Detection Range ± 130° from normal incidence
Relative Spectral Sensitivity

flat to ± 3% from 450 to 700 nm

down 8% of 400 nm and 36% at 350 nm

Further details can be found in the manufacturer's specification sheet.

BODC Processing

The data arrived at BODC in PSTAR format files representing all of the stainless steel CTD casts taken during the cruise. These were reformatted to the internal NetCDF format using standard BODC data banking procedures. The following table shows how the variables within the .2db files were mapped to appropriate BODC parameter codes:

Originator's Variable Units Description BODC Parameter Code Units Comment
press decibar Pressure (spatial co-ordinate) exerted by the water column PRESPR01 decibar  
temp deg C Temperature (ITS-90) of the water column (primary sensor) TEMPS901 deg C  
cond mS cm-1 Conductivity of the water column (primary sensor) CNDCST01 S m-1 Conductivity ÷ 10
temp2 deg C Temperature (ITS-90) of the water column (secondary sensor) TEMPS902 deg C  
cond2 mS cm-1 Conductivity of the water column (secondary sensor) CNDCST02 S m-1 Conductivity ÷ 10
alt m Height above seabed in the water column AHSFZZ01 m  
oxygen µmol Kg-1 Calibrated (independent samples) dissolved oxygen concentration measured with Sea-Bird SBE 43 sensor DOXYSC01 µmol L-1  
t2-t1 deg C Temperature difference between sensors (temp2 - temp)     Not transferred - not environmental measurement
c2-c1 deg C Conductivity difference between sensors (cond2 - cond)     Not transferred - not environmental measurement
ptemp deg C Temperature of CTD internal electronics     Not transferred - not environmental measurement
fluor µg L-1 Calibrated (manufacturer) concentration of chlorophyll a by in-situ fluorimeter CPHLPM01 mg m-3 µg L-1 = mg m3
nitrate µmol Calibrated (laboratory) concentration of dissolved nitrate by in-situ UV sensor     Dropped due to unreliability
trans % Transmittance of the water column by transmissometer POPTDR01 %  
lat deg Latitude north by GPS receiver     Not transferred
lon deg Longitude east by GPS receiver     Not transferred
PAR W m-2 Photosynthetically active radiation in the water column (down-welling) by 2π radiometer DWIRPP01 W m-2  
UPAR W m-2 Photosynthetically active radiation in the water column (up-welling) by 2π radiometer UWIRPP01 W m-2 In-house screening showed sensor was not present on CTD, therefore channel was deleted
flag None       Not transferred - unknown flag channel
salin psu Calibrated (independent samples) salinity of the water column (primary) PSALCC01 psu Derived from pressure, primary temperature and conductivity
salin2 psu Calibrated (independent samples) salinity of the water column (secondary) PSALCC02 psu Derived from pressure, secondary temperature and conductivity
potemp deg C Potential temperature with respect to the surface (primary)     Not transferred - derived
potemp2 deg C Potential temperature with respect to the surface (secondary)     Not transferred - derived
sigma0 kg m-3 Potential density with respect to the surface     Not transferred - calculated at BODC
sigma2 kg m-3 Potential density with respect to 2000 m     Not transferred - derived

Four new channels were generated from the originator's parameters during transfer and are described below:

BODC Parameter Code Units Description Comment
OXYSSC01 % Saturation of oxygen {O2} in the water column [dissolved phase] by Sea-Bird SBE 43 sensor and calibration against sample data and computation from concentration using Benson and Krause algorithm2  
SIGTPR01 Kg m-3 Sigma-theta of the water column by CTD and computation from salinity and potential temperature using UNESCO algorithm1 Computed from pressure, primary potential temperature and primary salinity
SIGTPR02 Kg m-3 Sigma-theta of the water column by CTD and computation from salinity and potential temperature using UNESCO algorithm1 Computed from pressure, secondary potential temperature and secondary salinity
TOKGPR01 L Kg-1 Conversion factor (volume to mass) for the water column by CTD and computation of density reciprocal from pressure, primary temperature and primary salinity  

The reformatted data were visualised using the in-house EDSERPLO software. Suspect data were marked by adding an appropriate quality control flag, missing data by both setting the data to an appropriate value and setting the quality control flag.

References

1Fofonoff N.P. and Millard R.C., Jr. (1983). Algorithms for computations of fundemental properties of seawater. UNESCO Technical Papers in Marine Science No. 44., 53pp.

2Benson, B.B. and Krause D., Jr. (1984). The concentration and isotopic fractionation of oxygen dissolved in freshwater and seawater in equilibrium with the atmosphere. Limnology and Oceanography, 29:620-632.

Originator's Data Processing

Sampling Strategy

A total of 84 CTD stations1 were carried out during the cruise in the areas of the Extended Ellett Line and Icelandic Basin. From these, a total of 92 CTD downcast profiles of 2 decibar data were collected2, of which, 75 profiles were obtained using the instruments associated to the stainless steel CTD. Using this unit, 21 profiles of data were collected as part of CTD survey 1 (C1), 3 as part of CTD survey 2 (C2), 16 as part of SeaSoar survey 1 (S1), 30 as part of SeaSoar survey 2 (S2) and 6 profiles of data were collected in the area of the Extended Ellett Line. General information regarding CTD sampling strategy can be found in the cruise report from p137.

1Please note that a total of 84 CTD 'profiles' were reported to have been carried out during the cruise on p137 of the cruise report, however, this actually refers to the number of CTD stations visited during the cruise.

2Please note that the collection of 94 profiles was attempted during the cruise but data were corrupted from cast 16220A and the CTD malfunctioned during cast 16295A. Therefore, only 92 profiles of data were collected.

Data Processing

Raw CTD files were initially processed through Sea-Bird software (SBEDataProcessing-Win32) using a modified protocol from Discovery cruise D306. The resulting files were then processed through NOCS Unix scripts into PSTAR format using slightly modified versions of execs used on cruise D306. Separate NOCS Unix scripts were used for stainless steel unit casts and titanium unit casts. Full processing details can be found in the cruise report from p138.

Field Calibrations

CTD salinity and oxygen were calibrated following the protocol described for salinity in the cruise report (p149, p150-151). Values obtained from the stainless steel CTD were calibrated using independent salinity and oxygen bottles samples, collected via the unit's OTE bottle rosette. Bottle samples were determined using an autosalinometer for salinity and the Winkler titration for oxygen. Further information regarding the collection and measurement of bottle samples can be found in the cruise report from p172 for salinity and p198 for oxygen. Prior to calibration, data points outside 2 standard deviation's of the mean offset (bottle value minus CTD value) were removed. The mean offset was found to vary for different periods of the cruise. Therefore, the cruise was split into two periods of calibration for salinity and three periods for oxygen. These were pre- and post-station 16224 for salinity and stations 16195-16202, 16203-16240 and 16243-16287 for oxygen. Due to time constraints, not all of the independent bottle samples had been processed at the time of writing the cruise report and revised calibrations are as below:

Stainless steel CTD

  • Salinity (primary sensor)
    • calibrated salinity = (-0.0752 + 1.0022) multiplied by raw (for casts 16195A to 16222A)
      calibrated salinity = (0.3462 + 0.9904) multiplied by raw (for casts 16224A to 16287A)
      where 'raw' is CTD primary salinity

  • Salinity (secondary sensor)
    • calibrated salinity = (-0.1914 + 1.0056) multiplied by raw (for casts 16195A to 16222A)
      calibrated salinity = (0.2754 + 0.9926) multiplied by raw (for casts 16224A to 16287A)
      where 'raw' is CTD secondary salinity

  • Oxygen
    • calibrated = (-13.0507 + 1.1583) multiplied by raw (for casts 16195A to 16202A)
      calibrated oxygen = (-12.4329 + 1.1370) multiplied by raw (for casts 16203A to 16240A)
      calibrated oxygen = (-8.6379 + 1.1346) multiplied by raw (for casts 16243A to 16287A)
      where 'raw' is CTD oxygen


Project Information

Oceans 2025 - The NERC Marine Centres' Strategic Research Programme 2007-2012

Who funds the programme?

The Natural Environment Research Council (NERC) funds the Oceans 2025 programme, which was originally planned in the context of NERC's 2002-2007 strategy and later realigned to NERC's subsequent strategy (Next Generation Science for Planet Earth; NERC 2007).

Who is involved in the programme?

The Oceans 2025 programme was designed by and is to be implemented through seven leading UK marine centres. The marine centres work together in coordination and are also supported by cooperation and input from government bodies, universities and other partners. The seven marine centres are:

  • National Oceanography Centre, Southampton (NOCS)
  • Plymouth Marine Laboratory (PML)
  • Marine Biological Association (MBA)
  • Sir Alister Hardy Foundation for Marine Science (SAHFOS)
  • Proudman Oceanographic Laboratory (POL)
  • Scottish Association for Marine Science (SAMS)
  • Sea Mammal Research Unit (SMRU)

Oceans2025 provides funding to three national marine facilities, which provide services to the wider UK marine community, in addition to the Oceans 2025 community. These facilities are:

  • British Oceanographic Data Centre (BODC), hosted at POL
  • Permanent Service for Mean Sea Level (PSMSL), hosted at POL
  • Culture Collection of Algae and Protozoa (CCAP), hosted at SAMS

The NERC-run Strategic Ocean Funding Initiative (SOFI) provides additional support to the programme by funding additional research projects and studentships that closely complement the Oceans 2025 programme, primarily through universities.

What is the programme about?

Oceans 2025 sets out to address some key challenges that face the UK as a result of a changing marine environment. The research funded through the programme sets out to increase understanding of the size, nature and impacts of these changes, with the aim to:

  • improve knowledge of how the seas behave, not just now but in the future;
  • help assess what that might mean for the Earth system and for society;
  • assist in developing sustainable solutions for the management of marine resources for future generations;
  • enhance the research capabilities and facilities available for UK marine science.

In order to address these aims there are nine science themes supported by the Oceans 2025 programme:

  • Climate, circulation and sea level (Theme 1)
  • Marine biogeochemical cycles (Theme 2)
  • Shelf and coastal processes (Theme 3)
  • Biodiversity and ecosystem functioning (Theme 4)
  • Continental margins and deep ocean (Theme 5)
  • Sustainable marine resources (Theme 6)
  • Technology development (Theme 8)
  • Next generation ocean prediction (Theme 9)
  • Integration of sustained observations in the marine environment (Theme 10)

In the original programme proposal there was a theme on health and human impacts (Theme 7). The elements of this Theme have subsequently been included in Themes 3 and 9.

When is the programme active?

The programme started in April 2007 with funding for 5 years.

Brief summary of the programme fieldwork/data

Programme fieldwork and data collection are to be achieved through:

  • physical, biological and chemical parameters sampling throughout the North and South Atlantic during collaborative research cruises aboard NERC's research vessels RRS Discovery, RRS James Cook and RRS James Clark Ross;
  • the Continuous Plankton Recorder being deployed by SAHFOS in the North Atlantic and North Pacific on 'ships of opportunity';
  • physical parameters measured and relayed in near real-time by fixed moorings and ARGO floats;
  • coastal and shelf sea observatory data (Liverpool Bay Coastal Observatory (LBCO) and Western Channel Observatory (WCO)) using the RV Prince Madog and RV Quest.

The data is to be fed into models for validation and future projections. Greater detail can be found in the Theme documents.


Oceans 2025 Theme 2: Marine Biogeochemical Cycles

Marine biogeochemical cycles are the key processes that control the cycling of climate-active gases within the surface ocean; the main transport mechanisms governing the supply of nutrients from deeper waters across the pycnocline; and the flux of material to deep water via the biological carbon pump. The broad aim of this Theme is to improve knowledge of major biogeochemical processes in the surface layer of the Atlantic Ocean and UK shelf seas in order to develop accurate models of these systems. This strategic research will result in predictions of how the ocean will respond to, and either ameliorate or worsen, climate change and ocean acidification.

Theme 2 comprises three Research Units and ten Work Packages. Theme 2 addresses the following pivotal biogeochemical pathways and processes:

  • The oceans and shelf seas as a source and sink of climate-active gases
  • The importance of the carbon and nitrogen cycles in the regulation of microbial communities and hence export and biogenic gas cycling
  • The biological pump and export of carbon into the ocean's interior
  • Processes that introduce nutrients into the euphotic zone
  • The direct impact of a high CO2 world (acidification) on mixed-layer biogeochemical cycles and feedbacks to the atmosphere via sea/air gas fluxes and the biological pump
  • The indirect impact of a high CO2 world (increased stratification and storminess) on the supply of nutrients to the surface layer of the ocean and hence on the biological carbon pump and air-sea gas fluxes
  • Cellular processes that mediate calcification in coccolithophores and how these are impacted by environmental change with a focus on elevated CO2 and ocean acidification
  • Inter- and intra-specific genetic diversity and inter-specific physiological plasticity in coccolithophores and the consequences of rapid environmental change

The official Oceans 2025 documentation for this Theme can be found using the following link: Oceans 2025 Theme 2


Oceans 2025 Theme 2, Work Package 2.5: Physical Processes and the Supply of Nutrients to the Euphotic Zone

The emphasis behind this Work Package is to gain a better understanding of the ocean's biological carbon pump (OBP), an important process in the global carbon cycle. Small changes in its magnitude resulting from climate change could have significant effects, both on the ocean's ability to sequester CO2 and on the natural flux of marine carbon. This work package is concerned with the effect of physical processes and circulation on nutrient supply to the euphotic zone. Many physical pathways influence nutrient supply, such as winter overturning, Ekman pumping, small-scale turbulent mixing and mesoscale ageostrophic circulations, (of which, eddy pumping is but one example). Increased stratification will change patterns of winter overturning and dampen small-scale mixing. Shifts in wind patterns will perturb Ekman pumping. Changes in gradients of ocean heating and wind-forcing will alter the distribution of potential energy released through baroclinic instability of eddies and fronts. The combined effect of change on total nutrient supply will therefore be complex. Such physically-mediated changes, coupled to changes in aeolian dust deposition, may profoundly alter upper ocean plankton communities, biogeochemical cycling and carbon export.

This Work Package will be primarily coordinated by the National Oceanography Centre, Southampton (NOC). Specific objectives are:

  • To determine the relative importance of mechanisms affecting nutrient supply to the photic zone by quantifying them in the three major biomes of the North Atlantic
  • To establish how representative process studies are for the basin scale and thus define operators to scale up the individual process study results
  • To determine the sensitivity to future climate change of the mechanisms sustaining total nutrient supply to the photic zone over the three major biomes of the North Atlantic

Aspects of this work will link to Oceans 2025 Theme 9 and 10, and Theme 2 WP 2.6.

More detailed information on this Work Package is available from pages 13-15 of the official Oceans 2025 Theme 2 document: Oceans 2025 Theme 2

Weblink: http://www.oceans2025.org/


Data Activity or Cruise Information

Cruise

Cruise Name D321 (D321A)
Departure Date 2007-07-24
Arrival Date 2007-08-23
Principal Scientist(s)John T Allen (National Oceanography Centre, Southampton)
Ship RRS Discovery

Complete Cruise Metadata Report is available here


Fixed Station Information


No Fixed Station Information held for the Series


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain
Q value below limit of quantification