Metadata Report for BODC Series Reference Number 938413


Metadata Summary

Data Description

Data Category Hydrography time series at depth
Instrument Type
NameCategories
Sea-Bird SBE 37-SMP MicroCAT C-T Sensor  water temperature sensor; salinity sensor
Instrument Mounting subsurface mooring
Originating Country United Kingdom
Originator Dr Miguel Morales Maqueda
Originating Organization Proudman Oceanographic Laboratory (now National Oceanography Centre, Liverpool)
Processing Status banked
Project(s) Rapid Climate Change Programme
RAPID-WAVE
 

Data Identifiers

Originator's Identifier B3LM#2/3682
BODC Series Reference 938413
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 2006-08-09 14:02
End Time (yyyy-mm-dd hh:mm) 2007-10-06 12:32
Nominal Cycle Interval 1800.0 seconds
 

Spatial Co-ordinates

Latitude 42.60000 N ( 42° 36.0' N )
Longitude 60.62500 W ( 60° 37.5' W )
Positional Uncertainty Unspecified
Minimum Sensor Depth 2950.0 m
Maximum Sensor Depth 2950.0 m
Minimum Sensor Height 250.0 m
Maximum Sensor Height 250.0 m
Sea Floor Depth 3200.0 m
Sensor Distribution Fixed common depth - All sensors are grouped effectively at the same depth which is effectively fixed for the duration of the series
Sensor Depth Datum Approximate - Depth is only approximate
Sea Floor Depth Datum Approximate - Depth is only approximate
 

Parameters

BODC CODE Rank Units Short Title Title
AADYAA01 1 Days Date(Loch_Day) Date (time from 00:00 01/01/1760 to 00:00 UT on day)
AAFDZZ01 1 Days Time(Day_Fract) Time (time between 00:00 UT and timestamp)
ACYCAA01 1 Dimensionless Record_No Sequence number
CNDCPR01 1 Siemens per metre InSituCond Electrical conductivity of the water body by in-situ conductivity cell
PSALPR01 1 Dimensionless P_sal Practical salinity of the water body by conductivity cell and computation using UNESCO 1983 algorithm
TEMPPR01 1 Degrees Celsius Temp Temperature of the water body
 

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database


Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."


Narrative Documents

Sea-Bird SBE 37-SMP MicroCAT

The SBE 37-SMP MicroCAT is a high accuracy conductivity and temperature recorder (pressure optional) with Serial interface, internal battery, non-volatile FLASH Memory and integral Pump. The Integral Pump runs for 1 second each time the MicroCAT samples, improving the conductivity response and giving improved anti-foul protection.

Designed for moorings and other long-duration, fixed-site deployments, MicroCATs have non-corroding titanium housings rated for operation to 7000 meters or pressure sensor full scale-range. Communication with the MicroCAT is over an internal, 3-wire, RS-232C link. The MicroCAT's aged and pressure-protected thermistor has a long history of exceptional accuracy and stability (typical drift is less than 0.002°C per year). Electrical isolation of the conductivity electronics eliminates any possibility of ground-loop noise.

Specifications

  Temperature
(°C)
Conductivity (S/m) Optional Pressure
Measurement Range -5 to +35 0 to 7 (0 to 70 mS/cm) 0 to full scale range: 20 / 100 / 350 / 600 / 1000 / 2000 / 3500 / 7000 metres
Initial accuracy 0.002 0.0003 0.1% of full scale range
Typical Stability 0.0002 per month 0.0003 per month 0.05% of full scale range per year
Resolution 0.0001 0.00001 0.002% of full scale range
Data Storage Temperature and conductivity: 6 bytes per sample
Time: 4 bytes per sample
Pressure (optional): 5 bytes per sample
Clock stability 5 seconds per month
Standard Internal Batteries Nominal 10.6 Ampere-hour pack consisting of twelve AA lithium batteries. Provides sufficient capacity for more than 100,000 samples for a typical sampling scheme
Housing Titanium pressure case rated at 7000 metres
Weight (without pressure) In water: 3kg
In air: 5kg

Further information can be found via the following link: Sea-Bird SBE 37-SMP MicroCAT Datasheet

RAPID WAVE Calibration Coefficients: Series 938413

BODC Series identifier 938413
Instrument Serial number 3682
Deployment cruise D308
Recovery cruise HUD2007045

Calibration Coefficients

A linear calibration of the form:

Calibrated = A * (Raw) + B

was applied to the original conductivity and temperature data (based on the instrument CTD dip performed during D308).

Variable Coefficient A Coefficient B
Conductivity 0.9921706 0.0266852
Temperature 0.999750 0.003016

The derived salinity was calibrated by multiplying values by 0.997423 and adding the offset of 0.092785. These coefficients were obtained by comparison of CTD salinity estimates to bottle salinities, as measured during the mooring deployment cruise, D308.

Anomalous salinity values in the series were identified using a threshold value of 0.006 / (30*60*60) 2 (PSU/second 2 ).

RAPID WAVE Sea-Bird MicroCAT data processing document

This document outlines the procedures undertaken to process and quality assure the MicroCAT data collected under the RAPID WAVE project.

Originator's processing

The raw data are downloaded from the instrument and converted to ASCII format. All processing is performed in Matlab.

Calculating calibration coefficients

A CTD dip is performed, typically on the deployment or recovery cruise, with the MicroCATs strapped onto the CTD frame. This allows calibration of the instruments by comparing the MicroCAT data with the CTD data. As the MicroCATs adjust much slower than the CTD, data are only compared during five minute stops on the upcast, after the sensors have stabilised. The synchronisation between the CTD and MicroCAT data for calibration is performed by visual examination of the pressure data from each instrument.

Linear regression coefficients for temperature, conductivity and pressure (if present) are determined by minimising, by a least-square method, the differences between the MicroCAT measurements and the reference CTD measurements.

Application of calibrations and salinity computation

Linear regression coefficients, obtained by comparison of MicroCAT data with concurrent CTD upcast data, are applied to the relevant MicroCAT data series to obtain calibrated temperature, conductivity and pressure (where present).

Time series of salinity for each instrument are derived from temperature, conductivity and pressure using UNESCO 1983 algorithms as implemented by the CSIRO seawater Matlab package version 3.2. For instruments without pressure sensors, pressure is interpolated linearly from the instruments deployed above and below, where available. Finally, where required, an additional calibration of the moored salinity data is performed by comparison of on-board CTD salinity estimates to bottle salinity measurements obtained during the relevant cruise.

Quality control

All channels are visually inspected for anomalous values. Salinity values are regarded as spikes if the discrete second-derivative with respect to time is greater in magnitude than a threshold value. The threshold value is found by eye, subjectively, for each instrument. All erroneous values established in this way are flagged accordingly.

BODC processing

The data files are submitted in ASCII format as one file per instrument. Once the submitted data files are safely archived, the data undergo standard reformatting and banking procedures:

Parameter mapping

The following describes the parameters contained in the originator's files and their mapping to BODC parameter codes :

Originator's variable Originator's units BODC parameter code BODC parameter definition BODC units Unit conversion Comments
Temperature (edited and calibrated) deg C TEMPPR01 Temperature of the water body deg C - -
Conductivity (edited and calibrated) Siemens/meter CNDCPR01 Electrical conductivity of the water body by in-situ conductivity cell Siemens/metre - -
Salinity PSU PSALPR01 Practical salinity of the water body by conductivity cell and computation using UNESCO 1983 algorithm - - See salinity computation (above)
Pressure (edited and calibrated) decibars PREXMCAT Pressure (measured variable) exerted by the water body by semi-fixed moored SBE MicroCAT decibars - -

Project Information

Rapid Climate Change (RAPID) Programme

Rapid Climate Change (RAPID) is a £20 million, six-year (2001-2007) programme of the Natural Environment Research Council (NERC). The programme aims to improve our ability to quantify the probability and magnitude of future rapid change in climate, with a main (but not exclusive) focus on the role of the Atlantic Ocean's Thermohaline Circulation.

Scientific Objectives

Projects

Overall 38 projects have been funded by the RAPID programme. These include 4 which focus on Monitoring the Meridional Overturning Circulation (MOC), and 5 international projects jointly funded by the Netherlands Organisation for Scientific Research, the Research Council of Norway and NERC.

The RAPID effort to design a system to continuously monitor the strength and structure of the North Atlantic Meridional Overturning Circulation is being matched by comparative funding from the US National Science Foundation (NSF) for collaborative projects reviewed jointly with the NERC proposals. Three projects were funded by NSF.

A proportion of RAPID funding as been made available for Small and Medium Sized Enterprises (SMEs) as part of NERC's Small Business Research Initiative (SBRI). The SBRI aims to stimulate innovation in the economy by encouraging more high-tech small firms to start up or to develop new research capacities. As a result 4 projects have been funded.


RAPID Western Atlantic Variability Experiment (WAVE)

Introduction

The RAPID WAVE project began in 2004 as an observational component of the U.K Natural Environment Research Council's RAPID Climate Change Programme in the western North Atlantic Ocean. In 2008, funding to continue RAPID WAVE was secured through the continuation programme, RAPID-WATCH, which is due to end in 2014.

The RAPID WAVE team brings together scientists at the National Oceanography Centre in Liverpool. Between 2004 and 2010, the RAPID WAVE team also contributed to the Line W mooring array, joining colleagues from the U.S. Line W is a U.S-led initiative used to monitor the North Atlantic Ocean's deep western boundary current whilst being funded through the U.S National Science Foundation and has been active since October 2001. It brings together scientists from Woods Hole Oceanographic Institution (WHOI) and Lamont-Doherty Earth Observatory (LDEO). Users of these data are referred to the Line W Project Website for more information.

In 2007, further collaboration was established with scientists at the Bedford Institute of Oceanography (BIO). This arrangement was formalised and continues under RAPID-WATCH. Smaller scale collaboration with scientists at the Instituto Espanol de Oceanografia (IEO) during RAPID-WATCH saw additional RAPID WAVE observational work in the eastern North Atlantic Ocean. This work commenced in 2009 as part of the RAPID WAVE RAPIDO campaign.

Scientific Rationale

The primary aim of the RAPID WAVE project is to develop an observing system that will identify the propagation of overturning signals, from high to low latitudes, along the western margin of the North Atlantic. It specifically aims to monitor temporal changes in the Deep Western Boundary Current and reveal how coherent the changes are along the slope. Ultimately it is envisaged that this will enable scientists to develop a better understanding of larger-scale overturning circulation in the Atlantic, and its wider impacts on climate.

Fieldwork

The fieldwork aspect of the project was to deploy arrays of Bottom Pressure Recorders (BPRs) and CTD moorings along specified satellite altimeter groundtracks off the eastern continental slope of Canada and the United States. In 2004, fieldwork focused on three array lines. Line A was established heading south west from the Grand Banks, whilst the Line B array ran south east on the continental slope of Nova Scotia. The third line, Line W, was an established hydrographic array on the continental slope of New England, serviced by Woods Hole Oceanographic Institute (WHOI), to which RAPID WAVE contributed BPR instrumentation.

The original intention was that each array would be serviced by a cruise every two years. However, following a very poor return rate of instrumentation during the first servicing cruise of Lines A and B in 2006, this plan was modified significantly, and the decision made to abandon work on Line A. In 2007, additional logistical support from Canada's Bedford Institute of Oceanography (BIO) enabled Line B to be serviced again after just one year of deployment, with a much improved recovery record.

The transition from RAPID to RAPID-WATCH funding marked significant changes to the RAPID WAVE observational system. Line B was abandoned and a joint array with BIO, known as the RAPID Scotia Line, to the south west was developed. This line receives annual servicing by BIO, with cruise participation from the RAPID WAVE team.

The servicing of RAPID WAVE BPRs on Line W remained a biennial activity during the RAPID and RAPID-WATCH programmes.

A small number of BPR deployments have also taken place off the coast of Spain as part of the RAPIDO element of RAPID WAVE.

Instrumentation

Types of instruments and measurements:

Contacts

Collaborator Organisation Project
Prof. Chris M. Hughes National Oceanography Centre, U.K RAPID WAVE
Dr. Miguel Angel Morales Maqueda National Oceanography Centre, U.K RAPID WAVE
Dr. Shane Elipot National Oceanography Centre, U.K RAPID WAVE
Dr. John M. Toole Woods Hole Oceanographic Institution, U.S Line W
Dr. Igor Yashayaev Bedford Institute of Oceanography, Canada -

Data Activity or Cruise Information

Data Activity

Start Date (yyyy-mm-dd) 2006-08-09
End Date (yyyy-mm-dd) 2007-10-06
Organization Undertaking ActivityProudman Oceanographic Laboratory (now National Oceanography Centre, Liverpool)
Country of OrganizationUnited Kingdom
Originator's Data Activity IdentifierB3LM#2
Platform Categorysubsurface mooring

RAPID Moored Instrument Rig B3LM#2

This rig was deployed as part of the Line B array of the RAPID WAVE project.

Deployment cruise RRS Discovery cruise D308
Recovery cruise CCGC Hudson cruise HUD2007045

The rig was anchored by a cast iron sinker and kept erect by groups of buoyancy spheres attached regularly along the mooring.

Instruments deployed on the rig

Depth Instrument
2220 m Sea-Bird SBE37 SMP MicroCAT (#3710)
2470 m Sea-Bird SBE37 SMP MicroCAT (#3681)
2695 m Aanderaa RCM 11 (#421)
2700 m Sea-Bird SBE37 SMP MicroCAT (#3713)
2950 m Sea-Bird SBE37 SMP MicroCAT (#3682)
3200 m POL Bottom Pressure Recorder (sensor DQ43122)

MicroCAT instruments with serial numbers #3681 and #3682 were not equipped with pressure sensors.

Other Series linked to this Data Activity - 938505 938401 938517 1040792

Cruise

Cruise Name D308
Departure Date 2006-07-24
Arrival Date 2006-08-15
Principal Scientist(s)Miguel Angel Morales Maqueda (Proudman Oceanographic Laboratory)
Ship RRS Discovery

Complete Cruise Metadata Report is available here


Fixed Station Information

Fixed Station Information

Station NameRAPID WAVE Site B3
CategoryOffshore location
Latitude42° 36.00' N
Longitude60° 36.00' W
Water depth below MSL3200.0 m

RAPID Mooring Site B3

This fixed station forms part of the Line B mooring array located to the east of Halifax, Nova Scotia, deployed as part of the RAPID WAVE project.

Period of collection August 2004 - October 2008

Site occupations

Mooring identifier Mooring type Deployment date Recovery date Parameters measured
B3RL#1 * RapidLander 21 Aug 2004 02 Aug 2006 Pressure and temperature
B3LM#1 ** Line Mooring 19 Aug 2004 - Temperature, conductivity, salinity and pressure
B3LM#2 Line Mooring 09 Aug 2006 06 Oct 2007 Temperature, conductivity, salinity, pressure and currents
B3LM#3 Line Mooring 07 Oct 2007 29 Sep 2008 Temperature, conductivity, salinity, pressure and currents

* Incorporated an Inverted Echo Sounder (IES)

** Mooring lost

Other Series linked to this Fixed Station for this cruise - 938401 938505 938517 1040792 1070124

Other Cruises linked to this Fixed Station (with the number of series) - CD160 (2) HUD07045 Leg2 (5)


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain