Search the data

Metadata Report for BODC Series Reference Number 974008


Metadata Summary

Data Description

Data Category CTD or STD cast
Instrument Type
NameCategories
Neil Brown MK3 CTD  CTD; water temperature sensor; salinity sensor; dissolved gas sensors
SeaTech transmissometer  transmissometers
Chelsea Technologies Group Aquatracka fluorometer  fluorometers
Instrument Mounting research vessel
Originating Country Netherlands
Originator Dr Tjeerd van Weering
Originating Organization Royal Netherlands Institute for Sea Research
Processing Status banked
Online delivery of data Download available - Ocean Data View (ODV) format
Project(s) OMEX I
 

Data Identifiers

Originator's Identifier 06
BODC Series Reference 974008
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 1994-05-29 09:51
End Time (yyyy-mm-dd hh:mm) -
Nominal Cycle Interval 2.0 decibars
 

Spatial Co-ordinates

Latitude 49.08650 N ( 49° 5.2' N )
Longitude 13.43333 W ( 13° 26.0' W )
Positional Uncertainty 0.0 to 0.01 n.miles
Minimum Sensor or Sampling Depth 4.96 m
Maximum Sensor or Sampling Depth 3651.43 m
Minimum Sensor or Sampling Height 18.57 m
Maximum Sensor or Sampling Height 3665.04 m
Sea Floor Depth 3670.0 m
Sea Floor Depth Source DATAHEAD
Sensor or Sampling Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor or Sampling Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
 

Parameters

BODC CODERankUnitsTitle
ATTNZR011per metreAttenuation (red light wavelength) per unit length of the water body by transmissometer
CPHLPR011Milligrams per cubic metreConcentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer
DOXYPR011Micromoles per litreConcentration of oxygen {O2 CAS 7782-44-7} per unit volume of the water body [dissolved plus reactive particulate phase] by in-situ Beckmann probe
NVLTAQ011VoltsRaw signal (voltage) of instrument output by Aquatracka nephelometer
OXYSBB011PercentSaturation of oxygen {O2 CAS 7782-44-7} in the water body [dissolved plus reactive particulate phase] by in-situ Beckmann probe and computation from concentration using Benson and Krause algorithm
POATCV011per metrePotential attenuance (unspecified wavelength) per unit length of the water body by transmissometer and computation using P-EXEC algorithm
POTMCV011Degrees CelsiusPotential temperature of the water body by computation using UNESCO 1983 algorithm
PRESPR011DecibarsPressure (spatial coordinate) exerted by the water body by profiling pressure sensor and correction to read zero at sea level
PSALST011DimensionlessPractical salinity of the water body by CTD and computation using UNESCO 1983 algorithm
SIGTPR011Kilograms per cubic metreSigma-theta of the water body by CTD and computation from salinity and potential temperature using UNESCO algorithm
TEMPST011Degrees CelsiusTemperature of the water body by CTD or STD

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database


Data Access Policy

Public domain data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

The recommended acknowledgment is

"This study uses data from the data source/organisation/programme, provided by the British Oceanographic Data Centre and funded by the funding body."


Narrative Documents

Neil Brown MK3 CTD

The Neil Brown MK3 conductivity-temperature-depth (CTD) profiler consists of an integral unit containing pressure, temperature and conductivity sensors with an optional dissolved oxygen sensor in a pressure-hardened casing. The most widely used variant in the 1980s and 1990s was the MK3B. An upgrade to this, the MK3C, was developed to meet the requirements of the WOCE project.

The MK3C includes a low hysteresis, titanium strain gauge pressure transducer. The transducer temperature is measured separately, allowing correction for the effects of temperature on pressure measurements. The MK3C conductivity cell features a free flow, internal field design that eliminates ducted pumping and is not affected by external metallic objects such as guard cages and external sensors.

Additional optional sensors include pH and a pressure-temperature fluorometer. The instrument is no longer in production, but is supported (repair and calibration) by General Oceanics.

Specifications

These specification apply to the MK3C version.

Pressure Temperature Conductivity
Range

6500 m

3200 m (optional)

-3 to 32°C 1 to 6.5 S cm-1
Accuracy

0.0015% FS

0.03% FS < 1 msec

0.0005°C

0.003°C < 30 msec

0.0001 S cm-1

0.0003 S cm-1 < 30 msec

Further details can be found in the specification sheet.

RRS Charles Darwin 86 CTD Data Documentation

Instrumentation

The CTD profiles of the water column and water samples at discrete horizons were taken with a Seabird SBE 911 plus CTD mounted inside a 22 bottle rosette array. The CTD probe incorporated a pressure sensor, conductivity cell, pressure protected high quality thermistor and a membrane dissolved oxygen sensor. In addition, attached to the CTD frame, were a Chelsea Instruments Mk III Aquatracka fluorometer, a Chelsea Instruments Mk III Aquatracka nephelometer and a SeaTech red light (661 nm) transmissometer with a 25 cm path length.

The rosette frame was equipped with twenty-two 12 litre NOEX bottles. The bases of the bottles were 0.5 m above the pressure head with their tops 0.5 m above it. One of the bottles was fitted with a holder for up to three digital reversing thermometers mounted 0.3 m above the CTD temperature sensor. As usual, there were intermittent problems with the NOEX bottles from contamination by leakage.

An underway CTD routine check station was held on 20th May. This was followed by a programme of CTD profiles of the water column along the OMEX transect with consecutive water sampling at discrete horizons.

Lowering rates were generally in the range of 0.5-1.0 m sec-1 but could be up to 1.5 m sec-1. Bottle samples and reversing thermometer measurements were acquired on the ascent of the CTD casts. Salinity determinations of bottle samples were partially done on board ship with the remainder being completed at the laboratory after the cruise. Oxygen concentrations from the majority of the bottle samples were also obtained on board by Winkler titration.

Data Acquisition

The data were logged on a PC using the SeaBird data acquisition software.

Post-Cruise Processing

The SeaBird DATCNV program was used for the conversion from binary raw data files to ASCII format in engineering units (PSU, °C, etc.). The data were then passed to Dr. Hendrik van Aken's group at NIOZ who worked up the temperature, salinity and oxygen channels. Details of the procedures used are not known but this group are associated with the collection of WOCE data and there is every reason to believe that the work was done to a very high standard.

The processed data were supplied to BODC.

Reformatting

The data as supplied had been binned to 1db with temperature (ITS90), practical salinity, chlorophyll (calibrated to µg/l), oxygen (µmol/kg), attenuance (per m) and nephelometer output (arbitraty units).

The data were converted into the BODC internal format (PXF) to allow the use of in-house software tools, notably the graphics editor. In addition to reformatting, the transfer program applied the following modifications to the data:

Dissolved oxygen was converted from µmol/kg to µM by multiplying the values by (1000+sigma-theta)/1000.

The chlorophyll was converted back to a voltage by a natural log transform to conform to the requirements of the BODC CTD data handling system. On retrieval, the data as supplied are reproduced.

Editing

Using a custom in-house graphics editor, the limits of the downcasts were delimited by manually applying flags to the cycle number channel.

No flagging of data other than garbage in the attenuance channel at depths greater than 2000 m on a couple of casts were required.

Once screened, the CTD downcasts were loaded into a database under the Oracle relational database management system.

Calibration

The salinity and temperature data had been calibrated prior to submission to BODC. No further calibration was required.

Inspection of the attenuance data showed the values in clear water to be too high, typically about 0.5. This is probably because no air correction had been applied to the data. Analysis of the data showed that the transmissometer was exceptionally stable and therefore a uniform correction factor (-0.132) was applied to all casts to normalise the data to a clear water value of 0.35.

The oxygen data were checked against the bottle data and this confirmed that the oxygen data had been calibrated against the bottle data set.

No extracted chlorophyll data were available for this cruise and consequently the data presented are the result of a nominal calibration. More heed should therefore be paid to the relative, rather than absolute, chlorophyll values.

Data Reduction

Once all screening and calibration procedures were completed, the data set was binned to 2 db (casts deeper than 100 db) or 1 db (casts shallower than 100 db). The binning algorithm excluded any data points flagged suspect and attempted linear interpolation over gaps up to 3 bins wide. If any gaps larger than this were encountered, the data in the gaps were set null.

Downcast values corresponding to the bottle firing depths were incorporated into the database. Oxygen saturations have been computed using the algorithm of Benson and Krause (1984).

Data Warnings

The fluorometer has not been calibrated against extracted chlorophyll data. The absolute values may therefore be meaningless.

References

Benson, B.B. and Krause, D. 1984. The concentration and isotopic fractionation of oxygen dissolved in fresh water and sea water in equilibrium with the atmosphere. Limnol. Oceanogr. 29 pp.620-632.

Aquatracka fluorometer

The Chelsea Instruments Aquatracka is a logarithmic response fluorometer. It uses a pulsed (5.5 Hz) xenon light source discharging between 320 and 800 nm through a blue filter with a peak transmission of 420 nm and a bandwidth at half maximum of 100 nm. A red filter with sharp cut off, 10% transmission at 664 nm and 678 nm, is used to pass chlorophyll-a fluorescence to the sample photodiode.

The instrument may be deployed either in a through-flow tank, on a CTD frame or moored with a data logging package.

Further details can be found in the manufacturer's specification sheet.

SeaTech Transmissometer

Introduction

The transmissometer is designed to accurately measure the the amount of light transmitted by a modulated Light Emitting Diode (LED) through a fixed-length in-situ water column to a synchronous detector.

Specifications

  • Water path length: 5 cm (for use in turbid waters) to 1 m (for use in clear ocean waters).
  • Beam diameter: 15 mm
  • Transmitted beam collimation: <3 milliradians
  • Receiver acceptance angle (in water): <18 milliradians
  • Light source wavelength: usually (but not exclusively) 660 nm (red light)

Notes

The instrument can be interfaced to Aanderaa RCM7 current meters. This is achieved by fitting the transmissometer in a slot cut into a customized RCM4-type vane.

A red LED (660 nm) is used for general applications looking at water column sediment load. However, green or blue LEDs can be fitted for specilised optics applications. The light source used is identified by the BODC parameter code.

Further details can be found in the manufacturer's Manual.


Project Information

Ocean Margin EXchange (OMEX) I

Introduction

OMEX was a European multidisciplinary oceanographic research project that studied and quantified the exchange processes of carbon and associated elements between the continental shelf of western Europe and the open Atlantic Ocean. The project ran in two phases known as OMEX I (1993-1996) and OMEX II - II (1997-2000), with a bridging phase OMEX II - I (1996-1997). The project was supported by the European Union under the second and third phases of its MArine Science and Technology Programme (MAST) through contracts MAS2-CT93-0069 and MAS3-CT97-0076. It was led by Professor Roland Wollast from Université Libre de Bruxelles, Belgium and involved more than 100 scientists from 10 European countries.

Scientific Objectives

The aim of the Ocean Margin EXchange (OMEX) project was to gain a better understanding of the physical, chemical and biological processes occurring at the ocean margins in order to quantify fluxes of energy and matter (carbon, nutrients and other trace elements) across this boundary. The research culminated in the development of quantitative budgets for the areas studied using an approach based on both field measurements and modeling.

OMEX I (1993-1996)

The first phase of OMEX was divided into sub-projects by discipline:

  • Physics
  • Biogeochemical Cycles
  • Biological Processes
  • Benthic Processes
  • Carbon Cycling and Biogases

This emphasises the multidisciplinary nature of the research.

The project fieldwork focussed on the region of the European Margin adjacent to the Goban Spur (off the coast of Brittany) and the shelf break off Tromsø, Norway. However, there was also data collected off the Iberian Margin and to the west of Ireland. In all a total of 57 research cruises (excluding 295 Continuous Plankton Recorder tows) were involved in the collection of OMEX I data.

Data Availability

Field data collected during OMEX I have been published by BODC as a CD-ROM product, entitled:

  • OMEX I Project Data Set (two discs)

Further descriptions of this product and order forms may be found on the BODC web site.

The data are also held in BODC's databases and subsets may be obtained by request from BODC.


Data Activity or Cruise Information

Cruise

Cruise Name CD86
Departure Date 1994-05-20
Arrival Date 1994-06-13
Principal Scientist(s)Tjeerd van Weering (Royal Netherlands Institute for Sea Research)
Ship RRS Charles Darwin

Complete Cruise Metadata Report is available here


Fixed Station Information

Fixed Station Information

Station NameOMEX I site OMEX3
CategoryOffshore area
Latitude49° 5.28' N
Longitude13° 23.40' W
Water depth below MSL3670.0 m

OMEX I Moored Instrument and CTD site OMEX3

OMEX3 was one of four fixed stations for the OMEX I project. It was visited by eleven cruises and collected a variety of data during the period June 1993 to October 1995. These include:

  • Mooring deployments - Aandeera current meters with transmissometers
  • CTD casts
  • Net trawls
  • Plankton recorders
  • Cores
  • Water samples

The data collected a site OMEX3 lay within a box bounded by co-ordinates 48° 56.9'N, 013° 42.69'W at the southwest corner and 49° 6.5'N, 013° 17.1'W at the northeast corner, with an approximate depth of 3650 metres.

Related Fixed Station activities are detailed in Appendix 1


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain
Q value below limit of quantification

Appendix 1: OMEX I site OMEX3

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.

Series IdentifierData CategoryStart date/timeStart positionCruise
920613CTD or STD cast1993-06-26 06:08:0049.06933 N, 13.429 WFS Poseidon PO200_7
319408Currents -subsurface Eulerian1993-06-26 14:31:0049.0942 N, 13.4288 WFS Poseidon PO200_7
319433Currents -subsurface Eulerian1993-06-26 14:43:0049.0942 N, 13.4288 WFS Poseidon PO200_7
319421Currents -subsurface Eulerian1993-06-26 16:26:0049.0942 N, 13.4288 WFS Poseidon PO200_7
920268CTD or STD cast1993-06-30 01:23:0049.003 N, 13.497 WValdivia VLD137
920281CTD or STD cast1993-06-30 03:09:0049.015 N, 13.519 WValdivia VLD137
883871CTD or STD cast1993-09-26 06:12:0049.08983 N, 13.37367 WRV Belgica BG9322A
883883CTD or STD cast1993-09-26 09:08:0049.1185 N, 13.42367 WRV Belgica BG9322A
1271535Water sample data1993-09-26 09:52:0049.11844 N, 13.42365 WRV Belgica BG9322A
883895CTD or STD cast1993-09-26 15:28:0049.12883 N, 13.43617 WRV Belgica BG9322A
883902CTD or STD cast1993-09-26 18:36:0049.14583 N, 13.482 WRV Belgica BG9322A
1271560Water sample data1993-09-26 18:46:0049.14583 N, 13.48192 WRV Belgica BG9322A
914877CTD or STD cast1993-10-24 09:14:0049.08333 N, 13.43 WRV Pelagia PE093
908177CTD or STD cast1994-01-07 05:16:0049.07333 N, 13.415 WFS Meteor M27_1
908189CTD or STD cast1994-01-07 21:22:0049.05667 N, 13.40833 WFS Meteor M27_1
908190CTD or STD cast1994-01-08 04:17:0049.08167 N, 13.43 WFS Meteor M27_1
444345Currents -subsurface Eulerian1994-01-08 07:34:0049.0942 N, 13.41 WFS Meteor M27_1
444357Currents -subsurface Eulerian1994-01-08 07:37:0049.0942 N, 13.41 WFS Meteor M27_1
444333Currents -subsurface Eulerian1994-01-08 07:39:0049.0942 N, 13.41 WFS Meteor M27_1
908208CTD or STD cast1994-01-08 08:00:0049.08 N, 13.435 WFS Meteor M27_1
887491CTD or STD cast1994-04-30 02:24:0049.0845 N, 13.30117 WRRS Charles Darwin CD85
887429CTD or STD cast1994-04-30 03:09:0049.08983 N, 13.3 WRRS Charles Darwin CD85
1663785Water sample data1994-05-29 08:37:0049.08648 N, 13.43338 WRRS Charles Darwin CD86
910342CTD or STD cast1994-09-14 18:58:0049.09083 N, 13.41133 WFS Meteor M30_1
442953Currents -subsurface Eulerian1994-09-15 09:30:0049.0883 N, 13.39 WFS Meteor M30_1
442977Currents -subsurface Eulerian1994-09-15 10:08:0049.0883 N, 13.39 WFS Meteor M30_1
442965Currents -subsurface Eulerian1994-09-15 14:35:0049.0883 N, 13.39 WFS Meteor M30_1
915021CTD or STD cast1995-08-23 06:10:0049.08317 N, 13.43067 WRV Pelagia PE95A
886463CTD or STD cast1995-09-30 05:45:0049.084 N, 13.4195 WRRS Discovery D217
1676267Water sample data1995-09-30 06:23:0049.08403 N, 13.41943 WRRS Discovery D217
886395CTD or STD cast1995-10-06 09:27:0049.091 N, 13.38417 WRRS Discovery D217
1676311Water sample data1995-10-06 11:18:0049.09093 N, 13.38417 WRRS Discovery D217
886402CTD or STD cast1995-10-06 14:00:0049.08067 N, 13.4025 WRRS Discovery D217
1676323Water sample data1995-10-06 14:15:0049.08059 N, 13.40249 WRRS Discovery D217
886414CTD or STD cast1995-10-07 05:01:0049.07717 N, 13.38917 WRRS Discovery D217
886426CTD or STD cast1995-10-07 08:07:0049.0835 N, 13.41383 WRRS Discovery D217