Metadata Report for BODC Series Reference Number 2046054

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

DY113 CTD Quality Control Report

Altimetry

Flags applied to all cycles >100m above bed in almost all casts in the altimeter channel (not necessary for shallow casts). This is because altimeter does not give accurate data readings until the sensor is within 100m of the seabed. From CTD055 onwards the altimetry channels contain an anomalous echo return at 200 m and occasionally 300 m range. These cycles were also flagged.

Backscatter

Some anomalous spikes have been flagged as suspect in the backscatter channel for most casts. Some cycle readings below parameter limits were also automatically flagged in some casts. The highest of these was approximately 15% of the cycles. The entire backscatter channel was null in CTD089. For this reason, the null backscatter channel was deleted from this cast.

Fluorescence

In 13 casts, flags have been applied to a small number of anomalous spikes and some cycles had flags automatically applied to them where the recordings were below the parameter limits in the fluorescence channel.

Irradiance

There are 32 casts where sampling occurred at night and because of this, the irradiance channels are constant and have been flagged as suspect.

Temperature of Pressure

In cast CTD064 the entire temperature of pressure channel is constant at 6.06. For this reason, the entire channel has been flagged as suspect.

Transmittance & Attenuation

Recordings below parameter limits were automatically flagged in the transmittance and attenuation channels in 38 stations. The number of cycles flagged vary from a couple of cycles to as much as 95% of the channels in some casts. Low readings can be common in the Southern Ocean as waters can be quite clear. In addition, flags have been added to a small amount of anomalous spikes in some casts.

Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."

Narrative Documents

Sea-Bird Dissolved Oxygen Sensor SBE 43 and SBE 43F

The SBE 43 is a dissolved oxygen sensor designed for marine applications. It incorporates a high-performance Clark polarographic membrane with a pump that continuously plumbs water through it, preventing algal growth and the development of anoxic conditions when the sensor is taking measurements.

Two configurations are available: SBE 43 produces a voltage output and can be incorporated with any Sea-Bird CTD that accepts input from a 0-5 volt auxiliary sensor, while the SBE 43F produces a frequency output and can be integrated with an SBE 52-MP (Moored Profiler CTD) or used for OEM applications. The specifications below are common to both.

Specifications

Further details can be found in the manufacturer's specification sheet.

DY113 ORCHESTRA CTD Instrumentation

CTD Unit and Auxillary Sensors

The Sea-Bird Scientific SBE911plus CTD was mounted on a NMF 24-way Stainless Steel CTD frame with 24 10L OTE water samplers fitted. The CTD was fitted with the following scientific sensors:

The Secondary CTD, located on the vane, was used as the main sensor except on cast 20 when a salp was sucked into the secondary duct.

Sea-Bird Electronics SBE 911 and SBE 917 series CTD profilers

The SBE 911 and SBE 917 series of conductivity-temperature-depth (CTD) units are used to collect hydrographic profiles, including temperature, conductivity and pressure as standard. Each profiler consists of an underwater unit and deck unit or SEARAM. Auxiliary sensors, such as fluorometers, dissolved oxygen sensors and transmissometers, and carousel water samplers are commonly added to the underwater unit.

Underwater unit

The CTD underwater unit (SBE 9 or SBE 9 plus) comprises a protective cage (usually with a carousel water sampler), including a main pressure housing containing power supplies, acquisition electronics, telemetry circuitry, and a suite of modular sensors. The original SBE 9 incorporated Sea-Bird's standard modular SBE 3 temperature sensor and SBE 4 conductivity sensor, and a Paroscientific Digiquartz pressure sensor. The conductivity cell was connected to a pump-fed plastic tubing circuit that could include auxiliary sensors. Each SBE 9 unit was custom built to individual specification. The SBE 9 was replaced in 1997 by an off-the-shelf version, termed the SBE 9 plus, that incorporated the SBE 3 plus (or SBE 3P) temperature sensor, SBE 4C conductivity sensor and a Paroscientific Digiquartz pressure sensor. Sensors could be connected to a pump-fed plastic tubing circuit or stand-alone.

Temperature, conductivity and pressure sensors

The conductivity, temperature, and pressure sensors supplied with Sea-Bird CTD systems have outputs in the form of variable frequencies, which are measured using high-speed parallel counters. The resulting count totals are converted to numeric representations of the original frequencies, which bear a direct relationship to temperature, conductivity or pressure. Sampling frequencies for these sensors are typically set at 24 Hz.

The temperature sensing element is a glass-coated thermistor bead, pressure-protected inside a stainless steel tube, while the conductivity sensing element is a cylindrical, flow-through, borosilicate glass cell with three internal platinum electrodes. Thermistor resistance or conductivity cell resistance, respectively, is the controlling element in an optimized Wien Bridge oscillator circuit, which produces a frequency output that can be converted to a temperature or conductivity reading. These sensors are available with depth ratings of 6800 m (aluminium housing) or 10500 m (titanium housing). The Paroscientific Digiquartz pressure sensor comprises a quartz crystal resonator that responds to pressure-induced stress, and temperature is measured for thermal compensation of the calculated pressure.

Additional sensors

Optional sensors for dissolved oxygen, pH, light transmission, fluorescence and others do not require the very high levels of resolution needed in the primary CTD channels, nor do these sensors generally offer variable frequency outputs. Accordingly, signals from the auxiliary sensors are acquired using a conventional voltage-input multiplexed A/D converter (optional). Some Sea-Bird CTDs use a strain gauge pressure sensor (Senso-Metrics) in which case their pressure output data is in the same form as that from the auxiliary sensors as described above.

Deck unit or SEARAM

Each underwater unit is connected to a power supply and data logging system: the SBE 11 (or SBE 11 plus) deck unit allows real-time interfacing between the deck and the underwater unit via a conductive wire, while the submersible SBE 17 (or SBE 17 plus) SEARAM plugs directly into the underwater unit and data are downloaded on recovery of the CTD. The combination of SBE 9 and SBE 17 or SBE 11 are termed SBE 917 or SBE 911, respectively, while the combinations of SBE 9 plus and SBE 17 plus or SBE 11 plus are termed SBE 917 plus or SBE 911 plus.

Specifications

Specifications for the SBE 9 plus underwater unit are listed below:

Further details can be found in the manufacturer's specification sheet.

SeaBird SBE35 Deep Ocean Standards Thermometer

The SBE 35 is a high precision thermometer that can be used in fixed point cells or at depths up to 6800 m. It is not affected by shock and vibration, allowing it to be used in calibration laboratories and for thermodynamic measurement of hydro turbine efficiency.

The SBE35 can be used with the SBE32 Carousel Water Sampler and with a real-time or autonomous CTD system. In this case, an SBE35 temperature measurement is collected each time a bottle is fired and the value is stored in EEPROM (Electrically Erasable Programmable Read-Only Memory), eliminating the need for reversing thermometers while providing a high accuracy temperature reading.

The SBE35 is standardized in water triple point (0.0100 °C) and gallium melting point (29.7646 °C) cells, following the methodology applied to the Standard-Grade Platinum Resistance Thermometer (SPRT). However, it does not need a resistance bridge, making it more cost-efficient than an SPRT.

Temperature is determined by applying an AC excitation to reference resistances and an ultrastable aged thermistor. Each of the resulting outputs is digitized by a 20-bit A/D converter. The AC excitation and ratiometric comparison uses a common processing channel, which removes measurement errors due to parasitic thermocouples, offset voltages, leakage currents and gain errors.

Specifications

Further details can be found in the manufacturer's specification sheet and manual.

Chelsea Technologies Group Aquatracka MKIII fluorometer

The Chelsea Technologies Group Aquatracka MKIII is a logarithmic response fluorometer. Filters are available to enable the instrument to measure chlorophyll, rhodamine, fluorescein and turbidity.

It uses a pulsed (5.5 Hz) xenon light source discharging along two signal paths to eliminate variations in the flashlamp intensity. The reference path measures the intensity of the light source whilst the signal path measures the intensity of the light emitted from the specimen under test. The reference signal and the emitted light signals are then applied to a ratiometric circuit. In this circuit, the ratio of returned signal to reference signal is computed and scaled logarithmically to achieve a wide dynamic range. The logarithmic conversion accuracy is maintained at better than one percent of the reading over the full output range of the instrument.

Two variants of the instrument are available, both manufactured in titanium, capable of operating in depths from shallow water down to 2000 m and 6000 m respectively. The optical characteristics of the instrument in its different detection modes are visible below:

* The wavelengths for the turbidity filters are customer selectable but must be in the range 400 to 700 nm. The same wavelength is used in the excitation path and the emission path.

The instrument measures chlorophyll a, rhodamine and fluorescein with a concentration range of 0.01 µg l^-1 to 100 µg l^-1. The concentration range for turbidity is 0.01 to 100 FTU (other wavelengths are available on request).

The instrument accuracy is ± 0.02 µg l^-1 (or ± 3% of the reading, whichever is greater) for chlorophyll a, rhodamine and fluorescein. The accuracy for turbidity, over a 0 - 10 FTU range, is ± 0.02 FTU (or ± 3% of the reading, whichever is greater).

Further details are available from the Aquatracka MKIII specification sheet.

Biospherical Instruments QCP-2350 [underwater] PAR sensor

A cosine-corrected PAR quantum irradiance profiling sensor. For use in underwater applications with 24 bit ADC systems. Measures light available for photosynthesis on a flat surface. Operation is by a single channel compressed analog output voltage that is proportional to the log of incident PAR (400-700 nm) irradiance. The sensor is designed for operation in waters to depths of up to 2,000 m (standard) or 6,800 m (optional).

For more information, please see this document: https://www.bodc.ac.uk/data/documents/nodb/pdf/Biospherical_QCP2300_QCP2350_Apr2014.pdf

WETLabs Single-angle Backscattering Meter ECO BB

An optical scattering sensor that measures scattering at 117°. This angle was determined as a minimum convergence point for variations in the volume scattering function induced by suspended materials and water. The measured signal is less determined by the type and size of the materials in the water and is more directly correlated to their concentration.

Several versions are available, with minor differences in their specifications:

• ECO BB(RT)provides analog or RS-232 serial output with 4000 count range
• ECO BB(RT)D adds the possibility of being deployed in depths up to 6000 m while keeping the capabilities of ECO BB(RT)
• ECO BB provides the capabilities of ECO BB(RT) with periodic sampling
• ECO BBB is similar to ECO BB but with internal batteries for autonomous operation
• ECO BBS is similar to ECO BB but with an integrated anti-fouling bio-wiper
• ECO BBSB has the capabilities of ECO BBS but with internal batteries for autonomous operation

Specifications

Further details can be found in the manufacturer's specification sheet.

Tritech Digital Precision Altimeter PA200

This altimeter is a sonar ranging device that gives the height above the sea bed when mounted vertically. When mounted in any other attitude the sensor provides a subsea distance. It can be configured to operate on its own or under control from an external unit and can be supplied with simultaneous analogue and digital outputs, allowing them to interface to PC devices, data loggers, telemetry systems and multiplexers.

These instruments can be supplied with different housings, stainless steel, plastic and aluminum, which will limit the depth rating. There are three models available: the PA200-20S, PA200-10L and the PA500-6S, whose transducer options differ slightly.

Specifications

Common specifications are presented below

Further details can be found in the manufacturer's specification sheet.

WETLabs C-Star transmissometer

This instrument is designed to measure beam transmittance by submersion or with an optional flow tube for pumped applications. It can be used in profiles, moorings or as part of an underway system.

Two models are available, a 25 cm pathlength, which can be built in aluminum or co-polymer, and a 10 cm pathlength with a plastic housing. Both have an analog output, but a digital model is also available.

This instrument has been updated to provide a high resolution RS232 data output, while maintaining the same design and characteristics.

Specifications

Further details are available in the manufacturer's specification sheet or user guide.

DY113 ORCHESTRA CTD Data: Originator's Processing

Sampling Strategy

A total of 104 CTD casts were carried out during the DY113 cruise using a Sea-Bird Scientific SBE9plus underwater unit and an NMF 24-way stainless steel CTD frame equipped with 24 10L OTE water samplers. DY113 occupied two repeat hydrographic sections, SR1b and A23 where 30 stations and 31 stations were sampled respectively. In addition, a CTD survey was made over 17 sites in Cumberland Bay, South Georgia, and a section along the North Scotia Ridge also occupied 25 stations. Water samples were collected from CTD Niskins, starting with the deepest Niskins in the following order: dissolved oxygen, oxygen isotopes, nutrients, nutrient isotopes, salinity, micro plastics and eDNA. Not every sample was collected from every Niskin or Depth. Further information on the DY113 CTD sampling can be found in the DY113 cruise report.

Originator's processing

The CTD data were collected at 24 Hz and logged to a PC running Seabird SeaSave version 7.26.7.121. Basic CTD data pre-processing of the raw data was completed using Sea-Bird data processing software 7.26.7.121. The pre-processing order used was:

• Data conversion
• AlignCTD 6s on oxygen channels only
• CellTM

The data were then processed using the Mexec processing routines developed at NOC. Some changes to the Mexec CTD processing were made on DY113, see page 16 of the DY113 cruise report for further details. All CTD processing and calibration for DY113 was executed using Mexec v3.2.

Calibration

The details on how the temperature, conductivity and oxygen sensors were calibrated can be found on page 18 of the DY113 cruise report.

Problems

The performance of the Benthos PSA-916T altimeter s/n: 59594 was variable but generally poor. After cast CTD048 the altimeter was replaced with the spare Benthos PSA-916T unit s/n: 62679 and the performance of this instrument was similarly poor. After cast CTD054, the Benthos altimeter was replaced with a Tritech PA-200 unit s/n: 6196.112522. The performance of the Tritech was excellent with a working range of 100 m. Otherwise, there were no major technical issues with the CTD suite during the cruise and no scientific instruments required changing for spares.

DY113 ORCHESTRA CTD Data: Processing by BODC

The CTD data were supplied to BODC as 104 MSTAR formatted NetCDF files and were converted to the BODC internal format.

During transfer the originator's variables were mapped to unique BODC parameter codes. The following table shows the parameter mapping.

Following transfer the data were screened using BODC in-house visualisation software. Improbable data values were assigned the appropriate BODC data quality flag. Missing data values, where present, were changed to the missing data value and assigned a BODC data quality flag.

Second sensor parameters have been removed from the final file but can be provided on request.

Project Information

Ocean Regulation of Climate by Heat and Carbon Sequestration and Transports (ORCHESTRA)

The Ocean Regulation of Climate by Heat and Carbon Sequestration and Transports (ORCHESTRA) is a £8.4 million, five year (2016-2021) research programme funded by the Natural Environment Research Council (NERC). The aim of the research is to to advance the understanding of, and capability to predict, the Southern Ocean's impact on climate change via its uptake and storage of heat and carbon. The programme will significantly reduce uncertainties concerning how this uptake and storage by the ocean influences global climate, by conducting a series of unique fieldwork campaigns and innovative model developments.

Background

ORCHESTRA represents the first fully-unified activity by NERC institutes to address these challenges, and will draw in national and international partners to provide community coherence, and to build a legacy in knowledge and capability that will transcend the timescale of the programme itself.

It brings together science teams from six UK research institutions to investigate the role that the Southern Ocean plays in our changing climate and atmospheric carbon draw-down. It is led by British Antarctic Survey, in partnership with National Oceanography Centre, British Geological Survey, Plymouth Marine Laboratory, the Centre for Polar Observation and Modelling and the Sea Mammal Research Unit.

The oceans around Antarctica play a critical a key role in drawing down and storing large amounts of carbon and vast quantities of heat from from the atmosphere. Due to its remoteness and harsh environment, the Southern Ocean is the world's biggest data desert, and one of the hardest places to get right in climate models. The ORCHESTRA programme will make unique and important new measurements in the Southern Ocean using a range of techniques, including use of the world-class UK research vessel fleet, and deployments of innovative underwater robots. The new understanding obtained will guide key improvements to the current generation of computer models, and will enhance greatly our ability to predict climate into the future.

The scope of the programme includes interaction of the Southern Ocean with the atmosphere, exchange between the upper ocean mixed layer and the interior and exchange between the Southern Ocean and the global ocean.

Further details are available on the ORCHESTRA page.

Participants

Six different organisations are directly involved in research for ORCHESTRA. These institutions are:

• British Antarctic Survey (BAS)
• National Oceanography Centre (NOC)
• Plymouth Marine Laboratory (PML)
• British Geological Survey (BGS)
• Centre for Polar Observation and Modelling (CPOM)
• Sea Mammal Research Unit (SMRU)

GO-SHIP are a third party organisation that, although not directly involved with the programme, will conduct ship based observations that will also be used by ORCHESTRA.

Research details

Three Work Packages have been funded by the ORCHESTRA programme. These are described in brief below:

• Work Package 1: Interaction of the Southern ocean with the atmosphere
  WP1 will use new observations of surface fluxes and their controlling parameters in order to better constrain the exchanges of heat and carbon loss across the surface of the Southern Ocean.

• Work Package 2: Exchange between the upper ocean mixed layer and the interior.
  This work package will combine observationally-derived data and model simulations to determine and understand the exchanges between the ocean mixed layer and its interior.

• Work Package 3: Exchange between the Southern Ocean and the global ocean .
  This WP will use budget analyses of the hydrographic/tracer sections to diagnose the three-dimensional velocity field of the waters entering, leaving and recirculating within the Southern Atlantic sector of the Southern ocean.

• Fieldwork and data collection

  The campaign consists of 12 core cruises on board the NERC research vessels RRS James Clark Ross and RRS James Cook and will include hydrographic/tracer sections conducted across Drake Passage (SR1b), the northern Weddell Sea/Scotia Sea (A23), the northern rim of the Weddell Gyre (ANDREXII) and across the South Atlantic (24S). Section I6S will be performed by GO-SHIP Project Partners. Measurements will include temperature, salinity, dissolved oxygen, velocity, dissolved inorganic carbon, total alkalinity, inorganic nutrients, oxygen and carbon isotopes, and underway meteorological and surface ocean observations including pCO₂.

  Tags will be deployed on 30 Weddel seals and these will provide temperature and salinity profiles that can be used alongside the Argo data.

  Autonomous underwater ocean gliders will conduct multi-month missions and will deliver data on ocean stratification, heat content, mixed layer depth and turbulent mixing over the upper 1 km, with previously-unobtainable temporal resolution. These gliders will be deployed in the Weddell Gyre and the ACC.

  Field campaigns with the MASIN meteorological aircrafts will be conducted flying out of Rothera and Halley research stations and the Falkland Islands. These campaigns will deliver information on key variables relating to air-sea fluxes (surface and air temperature, wind, humidity, atmospheric CO₂, radiation, turbulent fluxes of heat, momentum and CO₂), in different sea ice conditions and oceanic regimes.

  Eart Observation datasets will be used to inform the programme on the properties of the ocean, sea ice and atmosphere and on interactions between them.

  A cluster of 6 deep ocean moorings in the Orkney Passage will collect year round series of AABW temperatre and transport. This work connects to the NERC funded project Dynamics of the Orkney Passage Outflow (DYNOPO).

  The UK Earth System model (UKESM) and underlying physical model will be used to conduct analyses of heat and carbon uptake and transport by the Southern Ocean and their links to wider climate on decadal timescales.

  An eddy-resolving (1/12°) sector model of the ocean south of 30°S with 75 vertical levels, will be built using the NEMO model coupled to the Los Alamos sea ice (CICE) model. The improvements on the ocean boundary layer will be based from the results from the NERC-funded OSMOSIS project and the inclusion of tides.

  20-5 year runs of an adjoint model will be conducted to determine how key forcings and model states affect the uptake and subduction of heat and carbon by the ocean.

Data Activity or Cruise Information

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

North Scotia Ridge Hydrographic Section

The North Scotia Ridge Section (NSR) is a repeat hydrographic section along the ridge crest of the North Scotia Ridge running between the Falklands and South Georgia. The nominal end points of the section (to date) are 53° 57.256' S, 39° 38.702' W and 54° 23.653' S, 55° 40.552' W. It was first occupied in 2014 as part of the DIMES tracer release experiment (RRS James Clarke Ross cruise JR299) and has been repeated by the ORCHESTRA project (RRS Discovery cruise DY113) in 2020.

A table of cruises which occupied the NSR is presented below with links to the relevant cruise reports.

Related Fixed Station activities are detailed in Appendix 1

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: North Scotia Ridge Section - NSR

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.