Metadata Report for BODC Series Reference Number 343863

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

The pressure channel for some casts from the cruise include negative values.

The affected values have been flagged, but their presence casts doubt on the pressure calibration.

Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."

Narrative Documents

Bissett-Bermann 9040 Conductivity Temperature and Depth

The basic configuration of the B-B 9040 CTD incorporates pressure, temperature and conductivity sensors which could be logged digitally. This system also made it possible to derive other parameters, such as salinity, depth and sound velocity.

The instrument was versatile and it was possible to attach a dissolved oxygen sensor or to change the CTD housing, allowing it to obtain data from deeper layers in the water column. The accuracy for salinity is ±0.02 ppt , and ±0.02°C for temperature.

This instrument was also known as the Plessey 9040.

RRS Challenger Cruise 9/87 CTD Data Documentation

Introduction

Documentation for the CTD data collected on RRS Challenger Cruise 9/87 (January 1987) by the Scottish Marine Biological Association, Oban, Argyll, Scotland, UK, under the direction of D. J. Ellett.

Caution

Inspection of the pressure records from this cruise reveals several negative values (by up to 9db) at the start of some records, (while the temperature and salinity values appear reasonable), thus casting some doubt on the accuracy of the pressure calibration. These data values have been flagged.

Instrumentation

The instrument used was a Bissett Berman 9040 CTD system and the data were logged on a Hewlett Packard 9820 and stored in an integer format. Instrument lowering and raising speeds were between 0.5m/s and 1m/s. An acoustic pinger was placed above the CTD to give an accurate depth measurement, this could then be used to check the CTD pressure calibration. An NIO bottle with reversing thermometers was placed above the pinger, within 2m of the CTD system. A bottle sample was taken at the bottom of the cast providing the temperature and salinity are uniform at that point. If large temperature or salinity gradients were present then the bottle sample was triggered at a suitable site on the upcast. A surface salinity sample was also taken at the start of the dip.

Calibration

The CTD was not calibrated in the laboratory. The manufacturer's calibration was used and water samples taken to check the calibration and apply corrections where necessary.

Temperature

The manufacturer's calibration was used to convert the raw data to to physical units using the equation below:

Temperature (°C) = (10**6/Pt -2238.68/55.84)

where Pt is the temperature period in microseconds

These values were then plotted against the water bottle (i.e. reversing thermometer) temperatures and a regression line fitted to the data such that:

Temperature(WB) = m x Temperature(CTD) + c

Then the regression coefficients (m and c) were applied to correct the CTD temperature data - these are given in the table below.

Conductivity

The manufacturer's calibration was used to convert the raw data to to physical units using the equation below:

Conductivity (mmho/cm) = (10⁶/Pc - 4995)/58.12 + 10

where Pc is the conductivity period in microseconds

The water bottle salinities and corrected CTD temperatures were used to calculate the water bottle conductivity values. These values were then plotted against the CTD conductivities and a regression line fitted to the data such that:

Conductivity(WB) = m x Conductivity(CTD) + c

Then the regression coefficients were applied to correct the CTD conductivity data - these are given in the table below.

Pressure

The depths from the acoustic pinger were noted where the bottle samples were taken and then used to check the calibration of the pressure sensor - unless calibration values were available from the reversing thermometers. The equation below was used to convert the pressure period to physical units.

Pressure = (10⁶/Pd - 9712)/0.26267

where Pd is the pressure period in microseconds

A regression fit was carried out using the calibration values and the slope and intercept determined. The pressure values could then be corrected using:

Pressure (CORR) = m x Pressure(CTD) + c

The fit of the CTD data to the water bottle calibration data is given in the table below:

Data Processing

Obvious wild points were edited out of the calibration file and the calibration programs run to obtain values for the slopes and intercepts for temperature, pressure and conductivity. These were then applied to the uncalibrated data. Conductivities were converted to conductivity ratios and then converted to salinities using UNESCO recommended routines and sigma-t was calculated. The data values were then sieved to ensure a minimum separation between pressure values of 1 dbar. The data were then visually inspected and major spikes flagged.

References

Fofonoff, N.P. and Millard Jr., R.C. (1983).
Algorithms for the computation of fundamental properties of sea water. UNESCO Technical Paper on Marine Science 44.

Project Information

No Project Information held for the Series

Data Activity or Cruise Information

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

DML Station 5C

Station 5C is one of seven fixed STD/CTD stations between Lough Foyle (on the border between the Republic of Ireland and Northern Ireland) and Islay (Scotland). The station was established by scientists at Dunstaffnage Marine Laboratory (DML).

Related Fixed Station activities are detailed in Appendix 1

Fixed Station Information

DML Line C

Line C is a survey section between Lough Foyle (on the border between the Republic of Ireland and Northern Ireland) and Islay (off the west coast of Scotland). The line comprises seven fixed STD/CTD stations, which were established as part of routine monitoring work on the Scottish continental shelf by Dunstaffnage Marine Laboratory (DML). The line was occupied between the mid 1970s and mid 1990s.

Map of standard DML Line C STD/CTD Stations

Map produced using the GEBCO Digital Atlas.

The white triangles indicate the nominal positions of each standard station on DML Line C.

Nominal station details

DML Line C: Portrush/Lough Foyle (Northern Ireland) - Loch Indaal (Islay, Scotland)

In addition to Line C, there are other DML repeated survey transects which converge at Islay. These are Line B, Line D, and Line P.

Related Fixed Station activities are detailed in Appendix 2

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: DML Line C Station 5C

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.

Appendix 2: DML Line C

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.