Search the data

Metadata Report for BODC Series Reference Number 867176

Metadata Summary

Data Description

Data Category CTD or STD cast
Instrument Type
Neil Brown MK3 CTD  CTD; water temperature sensor; salinity sensor; dissolved gas sensors
SeaTech transmissometer  transmissometers
Chelsea Technologies Group Aquatracka fluorometer  fluorometers
Chelsea Technologies Group 2-pi PAR irradiance sensor  radiometers
Instrument Mounting research vessel
Originating Country United Kingdom
Originator Dr Axel Miller
Originating Organization Plymouth Marine Laboratory
Processing Status banked
Online delivery of data Download available - Ocean Data View (ODV) format
Project(s) OMEX II-II

Data Identifiers

Originator's Identifier CTD50
BODC Series Reference 867176

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 1998-01-14 16:04
End Time (yyyy-mm-dd hh:mm) -
Nominal Cycle Interval 2.0 decibars

Spatial Co-ordinates

Latitude 42.66883 N ( 42° 40.1' N )
Longitude 9.49717 W ( 9° 29.8' W )
Positional Uncertainty 0.0 to 0.01 n.miles
Minimum Sensor or Sampling Depth 0.99 m
Maximum Sensor or Sampling Depth 173.54 m
Minimum Sensor or Sampling Height 10.46 m
Maximum Sensor or Sampling Height 183.01 m
Sea Floor Depth 184.0 m
Sea Floor Depth Source -
Sensor or Sampling Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor or Sampling Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface


BODC CODERankUnitsTitle
ATTNZR011per metreAttenuation (red light wavelength) per unit length of the water body by transmissometer
ATTNZR021per metreAttenuation (red light wavelength) per unit length of the water body by transmissometer (second sensor)
CPHLPR011Milligrams per cubic metreConcentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer
FVLTAQ011VoltsRaw signal (voltage) of instrument output by in-situ Aquatracka chlorophyll fluorometer
IRRDPP011MicroEinsteins per square metre per secondDownwelling 2-pi scalar irradiance as photons of electromagnetic radiation (PAR wavelengths) in the water body by 2-pi scalar radiometer
LVLTPD011VoltsRaw signal (voltage) of instrument output by PML/Chelsea Instruments 2-pi PAR downwelling light meter
NVLTST011VoltsRaw signal (voltage) of instrument output by SeaTech light backscatter nephelometer (LBSS)
POATCV011per metrePotential attenuance (unspecified wavelength) per unit length of the water body by transmissometer and computation using P-EXEC algorithm
POTMCV011Degrees CelsiusPotential temperature of the water body by computation using UNESCO 1983 algorithm
PRESPR011DecibarsPressure (spatial coordinate) exerted by the water body by profiling pressure sensor and correction to read zero at sea level
PSALST011DimensionlessPractical salinity of the water body by CTD and computation using UNESCO 1983 algorithm
SIGTPR011Kilograms per cubic metreSigma-theta of the water body by CTD and computation from salinity and potential temperature using UNESCO algorithm
TEMPST011Degrees CelsiusTemperature of the water body by CTD or STD

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database

Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."

Narrative Documents

Neil Brown MK3 CTD

The Neil Brown MK3 conductivity-temperature-depth (CTD) profiler consists of an integral unit containing pressure, temperature and conductivity sensors with an optional dissolved oxygen sensor in a pressure-hardened casing. The most widely used variant in the 1980s and 1990s was the MK3B. An upgrade to this, the MK3C, was developed to meet the requirements of the WOCE project.

The MK3C includes a low hysteresis, titanium strain gauge pressure transducer. The transducer temperature is measured separately, allowing correction for the effects of temperature on pressure measurements. The MK3C conductivity cell features a free flow, internal field design that eliminates ducted pumping and is not affected by external metallic objects such as guard cages and external sensors.

Additional optional sensors include pH and a pressure-temperature fluorometer. The instrument is no longer in production, but is supported (repair and calibration) by General Oceanics.


These specification apply to the MK3C version.

Pressure Temperature Conductivity

6500 m

3200 m (optional)

-3 to 32°C 1 to 6.5 S cm-1

0.0015% FS

0.03% FS < 1 msec


0.003°C < 30 msec

0.0001 S cm-1

0.0003 S cm-1 < 30 msec

Further details can be found in the specification sheet.

Aquatracka fluorometer

The Chelsea Instruments Aquatracka is a logarithmic response fluorometer. It uses a pulsed (5.5 Hz) xenon light source discharging between 320 and 800 nm through a blue filter with a peak transmission of 420 nm and a bandwidth at half maximum of 100 nm. A red filter with sharp cut off, 10% transmission at 664 nm and 678 nm, is used to pass chlorophyll-a fluorescence to the sample photodiode.

The instrument may be deployed either in a through-flow tank, on a CTD frame or moored with a data logging package.

Further details can be found in the manufacturer's specification sheet.

Chelsea Technologies Photosynthetically Active Radiation (PAR) Irradiance Sensor

This sensor was originally designed to assist the study of marine photosynthesis. With the use of logarithmic amplication, the sensor covers a range of 6 orders of magnitude, which avoids setting up the sensor range for the expected signal level for different ambient conditions.

The sensor consists of a hollow PTFE 2-pi collector supported by a clear acetal dome diverting light to a filter and photodiode from which a cosine response is obtained. The sensor can be used in moorings, profiling or deployed in towed vehicles and can measure both upwelling and downwelling light.


Operation depth 1000 m
Range 2000 to 0.002 µE m-2 s-1
Angular Detection Range ± 130° from normal incidence
Relative Spectral Sensitivity

flat to ± 3% from 450 to 700 nm

down 8% of 400 nm and 36% at 350 nm

Further details can be found in the manufacturer's specification sheet.

SeaTech Transmissometer


The transmissometer is designed to accurately measure the the amount of light transmitted by a modulated Light Emitting Diode (LED) through a fixed-length in-situ water column to a synchronous detector.


  • Water path length: 5 cm (for use in turbid waters) to 1 m (for use in clear ocean waters).
  • Beam diameter: 15 mm
  • Transmitted beam collimation: <3 milliradians
  • Receiver acceptance angle (in water): <18 milliradians
  • Light source wavelength: usually (but not exclusively) 660 nm (red light)


The instrument can be interfaced to Aanderaa RCM7 current meters. This is achieved by fitting the transmissometer in a slot cut into a customized RCM4-type vane.

A red LED (660 nm) is used for general applications looking at water column sediment load. However, green or blue LEDs can be fitted for specilised optics applications. The light source used is identified by the BODC parameter code.

Further details can be found in the manufacturer's Manual.

RRS Charles Darwin 110 CTD Data Documentation

Instrumentation and Shipboard Procedures


The CTD profiles were taken with a Neil Brown Systems Mk IIIB CTD including a pressure sensor, a conductivity cell, a platinum resistance thermometer and a Beckmann dissolved oxygen sensor. However, the latter did not return any useful data.

The CTD unit was mounted vertically in the centre of a protective cage approximately 1.5m square.

The following instruments were also attached to the bars of the cage and logged as additional CTD channels:

  • Chelsea Instruments Aquatracka configured as a fluorometer.
  • SeaTech light backscatter sensor (LBSS nephelometer).
  • Two SeaTech 20-cm path-length red (661 nm) light transmissometers.
  • PML 2 PAR (photosynthetically available radiation) scalar irradiance sensor configured to measure downwelling (after CTD08) or upwelling radiation (up to CTD08).

Both upwelling and downwelling sensors were carried during the cruise. However, because there was a requirement for both an additional transmissometer and an altimeter there was only channel capacity in the multiplexer to log data from one light sensor.

Note that the downwelling light sensor was actually mounted on a pole placing it in line with the top of the water bottle rosette, 1.75 m above the pressure head. As a result, there was a vertical separation of some two metres between the upwelling and downwelling sensor positions. No geometrical correction of the light data has been attempted.

A General Oceanics 12-bottle tone-fire rosette pylon was fitted to the top of the CTD frame. 10-litre Niskin bottles were used throughout the cruise.

Data Acquisition

On each cast, the CTD was lowered continuously at 0.5 to 1.0 m s-1 to the closest comfortable proximity to the sea floor. The upcast was done in stages between the bottle firing depths. A tone fire system was installed to minimise the disruption caused to the data stream by the bottle-firing signal.

The data were logged by the RVS ABC data logging system. Output channels from the deck unit were logged at 32 Hz by a microprocessor interface (the Level A) which passed time-stamped averaged cycles at 1 Hz to a Sun workstation (the Level C) via a buffering system (the Level B).

On-Board Data Processing

The raw data comprised ADC counts. These were converted into engineering units (volts for PAR meters, fluorometer LBSS and transmissometers; ml l-1 for oxygen; mmho cm-1for conductivity; 7 °C for temperature; decibars for pressure) by the application of laboratory determined calibrations. Salinity (Practical Salinity Units as defined in Fofonoff and Millard, 1982) was calculated using the standard UNESCO function from the conductivity ratio (conductivity/42.914) and a time lagged temperature.

The data set were submitted to BODC in this form on Quarter Inch Cartridge tapes in RVS internal format for post-cruise processing and data banking.

Post-Cruise Processing and Calibration at BODC


The data were converted into the BODC internal format to allow the use of in-house software tools, notably the workstation graphics editor. In addition to reformatting, the transfer program applied the following modifications to the data:

  • Dissolved oxygen was converted from ml/l to µM by multiplication by 44.66.
  • Transmissometer voltages were corrected to the manufacturer's specified voltage by ratio using transmissometer air readings taken during the cruise (see the calibration section for details). The voltages were then converted to percentage transmission by multiplying them by 20 and to attenuance using the algorithm:
attenuance (m-1) = -5 loge (% transmission/100)


Reformatted CTD data were transferred onto a high-speed graphics workstation. Using custom in-house graphics editors, downcasts and upcasts were differentiated and the limits of the downcasts and upcasts were manually flagged.

Spikes on all the downcast channels were manually flagged. No data values were edited or deleted; flagging was achieved by modification of the associated quality control flag.

The pressure ranges over which the bottle samples had been collected were logged by manual interaction with the software. Usually, clusters of points recorded while the CTD was held stationary were used to determine this. These pressure ranges were subsequently used, in conjunction with a geometrical correction for the position of the water bottles with respect to the CTD pressure transducer, to determine the pressure range of data to be averaged for calibration values.

Once screened on the workstation, the CTD downcasts were loaded into a database under the ORACLE Relational Database Management System. 39 casts were loaded from leg A, and 12 casts were loaded from leg B. These were later migrated to the National Oceanographic Database.


With the exception of pressure, calibrations were done by comparison of CTD data against measurements made on water bottle samples or from the reversing thermometers mounted on the water bottles as in the case of temperature. In general, values were averaged from the CTD downcasts but where visual inspection of the data showed significant hysteresis values were manually extracted from the CTD upcasts.

All calibrations described here have been applied to the data.


The pressure calibration was derived by averaging pressures logged in air from 24 casts (leg A) and 10 casts (leg B). The mean corrections obtained were:

Leg A: Corrected pressure = Raw pressure - 3.24 (SD 0.28)
Leg B: Corrected pressure = Raw pressure - 3.52 (SD 0.22)

CTD temperatures were compared with calibrated digital reversing thermometer data. Excellent agreement was obtained with no evidence of drift or sudden offsets at any stage during the cruise. Consequently, no adjustment has been made to the CTD temperature data.


The CTD salinity data were calibrated against 15 (leg A) and 9 (leg B) water bottle samples analysed on a Guildline Autosal bench salinometer. The following corrections were obtained:

Leg A: Corrected salinity = Raw salinity + 0.030 (SD 0.005)
Leg B: Corrected salinity = Raw salinity + 0.031 (SD 0.003)
Optical Attenuance

Two brand new transmissometers, T1010D (ATTNZR01) and T1011D (ATTNZR02), were used in parallel during the cruise. Air readings were made in the laboratory shortly before the cruise, both directly (which confirmed the manufacturer's values) and through the CTD electronics using the same data channels as on the cruise. This gave the following results:

Instrument Direct CTD Correction
T1010D 4.684 4.653 -0.033
T1011D 4.670 4.621 -0.053

These corrections were applied to the data.

The minimum attenuance values from the two instruments were compared, on a cast by cast basis, with the following results:

CTD T1010D T1011D Difference
CTD06 0.49 0.49 -0.01
CTD07 0.44 0.44 0.00
CTD08 0.43 0.47 -0.04
CTD09 0.39 0.40 -0.01
CTD10 0.39 0.41 -0.02
CTD11 0.45 0.47 -0.02
CTD12 0.61 0.62 -0.01
CTD13 0.94 0.93 0.01
CTD14 0.56 0.62 -0.06
CTD15 0.45 0.48 -0.04
CTD16 0.42 0.44 -0.03
CTD17 0.82 0.82 0.00
CTD18 0.47 0.50 -0.03
CTD19 0.48 0.49 -0.02
CTD20 0.41 0.42 0.00
CTD21 0.78 0.72 0.07
CTD22 0.77 0.70 0.07
CTD23 0.70 0.65 0.04
CTD24 0.68 0.66 0.02
CTD25 0.67 0.67 0.00
CTD26 0.67 0.68 -0.01
CTD27 0.79 0.81 -0.02
CTD28 0.86 0.87 -0.01
CTD29 0.76 0.77 -0.01
CTD30 0.77 0.78 -0.01
CTD31 0.62 0.73 -0.11
CTD32 0.60 0.70 -0.10
CTD33 0.85 0.90 -0.05
CTD34 1.00 1.02 -0.02
CTD35 1.03 1.12 -0.09
CTD36 0.97 0.63 0.33
CTD37 1.04 0.53 0.52
CTD38 0.85 0.47 0.38
CTD39 0.71 0.44 0.27
CTD40 0.42 0.41 0.01
CTD41 0.41 0.43 -0.02
CTD42 0.39 0.41 -0.02
CTD43 0.40 0.41 -0.02
CTD44 0.40 0.42 -0.02
CTD45 0.39 0.40 -0.01
CTD46 0.49 0.51 -0.02
CTD47 0.50 0.51 -0.02
CTD48 0.49 0.53 -0.04
CTD49 0.38 0.40 -0.01
CTD50 0.49 0.50 -0.01
CTD51 0.63 0.63 0.00
CTD52 0.64 0.65 -0.01
CTD53 0.58 0.60 -0.01
CTD54 0.39 0.41 -0.01
CTD55 0.40 0.42 -0.01
CTD56 0.43 0.44 -0.02

This table shows the minimum attenuance (excluding values flagged as suspect during quality control) logged by each instrument on each CTD cast, together with the simple arithmetic difference (1010D - 1011D). The rows in italics have absolute differences <=0.01, the rows in bold have absolute differences >0.02, whilst the remaining rows have absolute differences from 0.01 to 0.02.

The general BODC conclusions from examination of these data are as follows:

  • Data from T1010D seem more accurate than T1011D for most casts, but there are exceptions. For example, the data from T1010D from casts CTD36-CTD39 are clearly wrong.
  • The clear water values from both instruments are higher than expected by approximately 0.02 (T1010D) to 0.04 (T1011D).
  • The instruments were more stable on leg B (CTD45 onwards).

However, users are advised to peruse the above table and come to their own conclusion as to whether the optical attenuance data from this cruise are adequate for the proposed purpose.

Further air readings were available from leg B of the cruise. However, these gave more variable results than the laboratory calibration.


The voltages logged by the ABC system from the SeaTech light backscatter sensor have been included in the database without the application of any further calibration.


The fluorometer was calibrated using extracted chlorophyll data assayed by HPLC from leg B of the cruise. CTD voltages were regressed against the natural log of the sum of chlorophyll-a and diavinyl chlorophyll-a. The result was the following calibration equation:

Chlorophyll (µg/l) = exp (voltage*1.01 - 1.6863) (N=42, R2=60%)

This has been used for both legs of the cruise.

Upwelling and Downwelling Irradiance

The following calibrations were applied to the voltages:

Downwelling irradiance ( Em-2s-1) = exp (-4.900*voltage + 7.237) * 0.0375
Sensor 1

Upwelling irradiance ( Em-2s-1) = exp (-4.970*voltage + 6.426) * 0.0375
Sensor 8

Note that the scaling factor (0.0375) is an empirically derived term that converts the data from Wcm-2 to Em-2s-1. Consequently, the data may be converted to Wm-2 if required by dividing by 3.75.

Data Reduction

Once all screening and calibration procedures were completed, the data set was binned to 2 db (casts deeper than 100 db) or 1 db (casts shallower than 100 db). The binning algorithm excluded any data points flagged suspect and attempted linear interpolation over gaps up to 3 bins wide. If any gaps larger than this were encountered, the data in the gaps were set null.

Oxygen saturation has been computed using the algorithm of Benson and Krause (1984)


Careful consideration should be given to the comparison of the transmissometers given above before making any use of the attenuance data.


Benson B.B. and Krause D. jnr. 1984. The concentration and isotopic fractionation of oxygen dissolved in fresh water and sea water in equilibrium with the atmosphere. Limnol. Oceanogr. 29 pp.620-632.

Fofonoff N.P. and Millard Jr., R.C. 1982. Algorithms for Computation of Fundamental Properties of Seawater. UNESCO Technical Papers in Marine Science 44.

Project Information

Ocean Margin EXchange (OMEX) II - II


OMEX was a European multidisciplinary oceanographic research project that studied and quantified the exchange processes of carbon and associated elements between the continental shelf of western Europe and the open Atlantic Ocean. The project ran in two phases known as OMEX I (1993-1996) and OMEX II - II (1997-2000), with a bridging phase OMEX II - I (1996-1997). The project was supported by the European Union under the second and third phases of its MArine Science and Technology Programme (MAST) through contracts MAS2-CT93-0069 and MAS3-CT97-0076. It was led by Professor Roland Wollast from Université Libre de Bruxelles, Belgium and involved more than 100 scientists from 10 European countries.

Scientific Objectives

The aim of the Ocean Margin EXchange (OMEX) project was to gain a better understanding of the physical, chemical and biological processes occurring at the ocean margins in order to quantify fluxes of energy and matter (carbon, nutrients and other trace elements) across this boundary. The research culminated in the development of quantitative budgets for the areas studied using an approach based on both field measurements and modeling.

OMEX II - II (1997-2000)

The second phase of OMEX concentrated exclusively on the Iberian Margin, although RV Belgica did make some measurements on La Chapelle Bank whilst on passage to Zeebrugge. This is a narrow-shelf environment, which contrasts sharply with the broad shelf adjacent to the Goban Spur. This phase of the project was also strongly multidisciplinary in approach, covering physics, chemistry, biology and geology.

There were a total of 33 OMEX II - II research cruises, plus 23 CPR tows, most of which were instrumented. Some of these cruises took place before the official project start date of June 1997.

Data Availability

Field data collected during OMEX II - II have been published by BODC as a CD-ROM product, entitled:

  • OMEX II Project Data Set (three discs)

Further descriptions of this product and order forms may be found on the BODC web site.

The data are also held in BODC's databases and subsets may be obtained by request from BODC.

Data Activity or Cruise Information


Cruise Name CD110B
Departure Date 1998-01-06
Arrival Date 1998-01-19
Principal Scientist(s)Axel E J Miller (Plymouth Marine Laboratory)
Ship RRS Charles Darwin

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

Station NameOMEX II-II Repeat Section P
CategoryOffshore route/traverse

OMEX II-II Repeat Section P

Section P was one of ten repeat sections sampled during the Ocean Margin EXchange (OMEX) II-II project between June 1997 and October 1999.

The CTD measurements collected at repeat section P, at the Iberian Margin, lie within a box bounded by co-ordinates 42° 30.7' N, 10° 20.0' W at the southwest corner and 42° 40.9' N, 09° 8.9' W at the northeast corner.

Cruises occupying section P

Cruise Start Date End Date
RRS Charles Darwin 105B 10/06/1997 22/06/1997
RV Belgica 9714C 21/06/1997 30/06/1997
RRS Charles Darwin 110A 23/12/1997 05/01/1998
RRS Charles Darwin 110B 06/01/1998 19/01/1998
RV Belgica 9815C 27/06/1998 07/07/1998
RRS Charles Darwin 114A 29/07/1998 11/08/1998
RV Professor Shtokman 0898 01/08/1998 11/08/1998
FS Meteor 43_2 28/12/1998 14/01/1999
RV Belgica 9919B 04/09/1999 11/09/1999
RV Belgica 9919C 14/09/1999 18/09/1999
RV Thalassa 1099 13/10/1999 20/10/1999

Related Fixed Station activities are detailed in Appendix 1

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain
B nominal value
Q value below limit of quantification

Appendix 1: OMEX II-II Repeat Section P

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.

Series IdentifierData CategoryStart date/timeStart positionCruise
866449CTD or STD cast1997-06-10 14:24:0042.67417 N, 9.57717 WRRS Charles Darwin CD105B
866554CTD or STD cast1997-06-13 05:26:0042.66617 N, 9.20967 WRRS Charles Darwin CD105B
866566CTD or STD cast1997-06-13 07:25:0042.66667 N, 9.366 WRRS Charles Darwin CD105B
865827CTD or STD cast1997-06-13 08:44:0042.66717 N, 9.50017 WRRS Charles Darwin CD105B
866578CTD or STD cast1997-06-13 10:19:0042.66567 N, 9.60533 WRRS Charles Darwin CD105B
866591CTD or STD cast1997-06-13 12:22:0042.663 N, 9.616 WRRS Charles Darwin CD105B
865839CTD or STD cast1997-06-13 14:33:0042.66717 N, 9.8475 WRRS Charles Darwin CD105B
866609CTD or STD cast1997-06-13 17:07:0042.667 N, 9.99983 WRRS Charles Darwin CD105B
866610CTD or STD cast1997-06-13 20:23:0042.66633 N, 10.29933 WRRS Charles Darwin CD105B
866020CTD or STD cast1997-06-20 12:21:0042.66833 N, 9.49433 WRRS Charles Darwin CD105B
866032CTD or STD cast1997-06-20 13:50:0042.66633 N, 9.55233 WRRS Charles Darwin CD105B
866044CTD or STD cast1997-06-20 15:04:0042.66583 N, 9.60183 WRRS Charles Darwin CD105B
864756CTD or STD cast1997-06-24 23:34:0042.66733 N, 9.20933 WRV Belgica BG9714C
864246CTD or STD cast1997-06-25 04:03:0042.6655 N, 9.4105 WRV Belgica BG9714C
864768CTD or STD cast1997-06-25 05:13:0042.65917 N, 9.40983 WRV Belgica BG9714C
864781CTD or STD cast1997-06-25 07:42:0042.66433 N, 9.53783 WRV Belgica BG9714C
1851589Water sample data1997-06-25 07:49:0042.66428 N, 9.53785 WRV Belgica BG9714C
864258CTD or STD cast1997-06-25 11:09:0042.65833 N, 9.70717 WRV Belgica BG9714C
864271CTD or STD cast1997-06-25 13:43:0042.65183 N, 9.71317 WRV Belgica BG9714C
1851590Water sample data1997-06-25 13:49:0042.65191 N, 9.71311 WRV Belgica BG9714C
864283CTD or STD cast1997-06-26 01:09:0042.6695 N, 10.30833 WRV Belgica BG9714C
864295CTD or STD cast1997-06-26 03:26:0042.67233 N, 10.32533 WRV Belgica BG9714C
864302CTD or STD cast1997-06-26 04:14:0042.67933 N, 10.3335 WRV Belgica BG9714C
866935CTD or STD cast1997-12-26 17:33:0042.6655 N, 9.21383 WRRS Charles Darwin CD110A
866959CTD or STD cast1997-12-27 12:05:0042.67617 N, 9.4935 WRRS Charles Darwin CD110A
866806CTD or STD cast1997-12-30 20:35:0042.6705 N, 9.20917 WRRS Charles Darwin CD110A
867164CTD or STD cast1998-01-14 06:46:0042.65617 N, 10.29883 WRRS Charles Darwin CD110B
867188CTD or STD cast1998-01-14 22:07:0042.66967 N, 9.50067 WRRS Charles Darwin CD110B
867207CTD or STD cast1998-01-15 02:31:0042.6675 N, 9.498 WRRS Charles Darwin CD110B
867219CTD or STD cast1998-01-15 05:57:0042.66833 N, 9.21067 WRRS Charles Darwin CD110B
867220CTD or STD cast1998-01-15 09:52:0042.669 N, 9.6105 WRRS Charles Darwin CD110B
867232CTD or STD cast1998-01-15 13:58:0042.67083 N, 9.59417 WRRS Charles Darwin CD110B
867244CTD or STD cast1998-01-15 20:45:0042.66667 N, 9.60733 WRRS Charles Darwin CD110B
865286CTD or STD cast1998-06-30 03:57:0042.67017 N, 9.3665 WRV Belgica BG9815C
865145CTD or STD cast1998-06-30 04:40:0042.6645 N, 9.367 WRV Belgica BG9815C
865157CTD or STD cast1998-06-30 11:17:0042.66867 N, 9.21367 WRV Belgica BG9815C
865169CTD or STD cast1998-06-30 13:56:0042.665 N, 9.50533 WRV Belgica BG9815C
864916CTD or STD cast1998-06-30 15:25:0042.67333 N, 9.61233 WRV Belgica BG9815C
864928CTD or STD cast1998-07-01 04:45:0042.66033 N, 9.70367 WRV Belgica BG9815C
865182CTD or STD cast1998-07-01 05:52:0042.66783 N, 9.71883 WRV Belgica BG9815C
865305CTD or STD cast1998-07-01 08:13:0042.656 N, 9.7225 WRV Belgica BG9815C
864941CTD or STD cast1998-07-01 15:18:0042.65733 N, 9.85267 WRV Belgica BG9815C
865194CTD or STD cast1998-07-01 17:34:0042.653 N, 9.8685 WRV Belgica BG9815C
864800CTD or STD cast1998-07-05 05:18:0042.65383 N, 10.31383 WRV Belgica BG9815C
864812CTD or STD cast1998-07-05 06:09:0042.66533 N, 10.31967 WRV Belgica BG9815C
864824CTD or STD cast1998-07-05 08:49:0042.67417 N, 10.31733 WRV Belgica BG9815C
864836CTD or STD cast1998-07-05 13:15:0042.67283 N, 9.9955 WRV Belgica BG9815C
864848CTD or STD cast1998-07-05 15:39:0042.67367 N, 9.99167 WRV Belgica BG9815C
1685904Water sample data1998-08-06 08:31:0042.66667 N, 9.21 WProfessor Shtokman OMEX-0898
888494CTD or STD cast1998-08-06 09:20:0042.66667 N, 9.21 WProfessor Shtokman OMEX-0898
1685916Water sample data1998-08-06 11:53:0042.66667 N, 9.49833 WProfessor Shtokman OMEX-0898
888501CTD or STD cast1998-08-06 12:45:0042.66667 N, 9.49833 WProfessor Shtokman OMEX-0898
1685928Water sample data1998-08-06 14:08:0042.66683 N, 9.604 WProfessor Shtokman OMEX-0898
888513CTD or STD cast1998-08-06 14:43:0042.66683 N, 9.604 WProfessor Shtokman OMEX-0898
1685941Water sample data1998-08-06 17:22:0042.66475 N, 9.84392 WProfessor Shtokman OMEX-0898
888525CTD or STD cast1998-08-06 18:07:0042.66483 N, 9.844 WProfessor Shtokman OMEX-0898
888537CTD or STD cast1998-08-07 09:49:0042.66683 N, 9.60017 WProfessor Shtokman OMEX-0898
1685953Water sample data1998-08-07 15:12:0042.666 N, 9.99967 WProfessor Shtokman OMEX-0898
888549CTD or STD cast1998-08-07 15:16:0042.666 N, 9.99967 WProfessor Shtokman OMEX-0898
888550CTD or STD cast1998-08-07 19:15:0042.66633 N, 10.299 WProfessor Shtokman OMEX-0898
1685965Water sample data1998-08-08 07:28:0042.66467 N, 10.29825 WProfessor Shtokman OMEX-0898
888562CTD or STD cast1998-08-08 08:16:0042.66467 N, 10.29817 WProfessor Shtokman OMEX-0898
876038CTD or STD cast1999-01-02 21:06:0042.6295 N, 10.06333 WFS Meteor M43_2
880234CTD or STD cast1999-09-05 20:05:0042.664 N, 9.35983 WRV Belgica BG9919B
880246CTD or STD cast1999-09-06 14:44:0042.67017 N, 9.71667 WRV Belgica BG9919B
880387CTD or STD cast1999-09-06 16:06:0042.6645 N, 9.71617 WRV Belgica BG9919B
880326CTD or STD cast1999-09-06 18:52:0042.66767 N, 9.50367 WRV Belgica BG9919B
880314CTD or STD cast1999-09-07 06:10:0042.666 N, 9.15267 WRV Belgica BG9919B
880086CTD or STD cast1999-09-07 06:51:0042.665 N, 9.15683 WRV Belgica BG9919B
880222CTD or STD cast1999-09-07 07:28:0042.66683 N, 9.14933 WRV Belgica BG9919B
880455CTD or STD cast1999-09-07 08:57:0042.66583 N, 9.1545 WRV Belgica BG9919B
880098CTD or STD cast1999-09-07 09:12:0042.66733 N, 9.15117 WRV Belgica BG9919B
880338CTD or STD cast1999-09-07 15:13:0042.6635 N, 9.835 WRV Belgica BG9919B
880511CTD or STD cast1999-09-07 16:35:0042.65367 N, 9.84367 WRV Belgica BG9919B
880523CTD or STD cast1999-09-07 19:31:0042.66467 N, 9.98917 WRV Belgica BG9919B
880129CTD or STD cast1999-09-07 20:11:0042.66433 N, 9.8985 WRV Belgica BG9919B
880467CTD or STD cast1999-09-08 06:05:0042.6655 N, 9.21067 WRV Belgica BG9919B
880479CTD or STD cast1999-09-08 06:40:0042.66583 N, 9.20467 WRV Belgica BG9919B
880105CTD or STD cast1999-09-08 07:11:0042.66533 N, 9.20383 WRV Belgica BG9919B
880480CTD or STD cast1999-09-10 06:02:0042.66433 N, 9.60633 WRV Belgica BG9919B
880492CTD or STD cast1999-09-10 06:41:0042.66767 N, 9.60917 WRV Belgica BG9919B
880117CTD or STD cast1999-09-10 07:14:0042.66883 N, 9.61533 WRV Belgica BG9919B
880664CTD or STD cast1999-09-15 06:08:0042.66683 N, 10.30117 WRV Belgica BG9919C
880676CTD or STD cast1999-09-15 06:44:0042.67067 N, 10.30333 WRV Belgica BG9919C
880688CTD or STD cast1999-09-15 07:33:0042.6715 N, 10.31717 WRV Belgica BG9919C
888734CTD or STD cast1999-10-16 14:34:0042.66083 N, 10.00367 WThalassa TH1099
888746CTD or STD cast1999-10-16 17:23:0042.66733 N, 9.8445 WThalassa TH1099
888758CTD or STD cast1999-10-16 20:35:0042.66317 N, 9.6075 WThalassa TH1099
888771CTD or STD cast1999-10-17 07:33:0042.67133 N, 9.59883 WThalassa TH1099
888783CTD or STD cast1999-10-17 09:29:0042.66817 N, 9.5035 WThalassa TH1099
888795CTD or STD cast1999-10-17 10:57:0042.669 N, 9.5535 WThalassa TH1099
888802CTD or STD cast1999-10-17 13:30:0042.66683 N, 9.30783 WThalassa TH1099
888814CTD or STD cast1999-10-17 14:36:0042.67 N, 9.20483 WThalassa TH1099
888826CTD or STD cast1999-10-17 20:30:0042.67183 N, 9.20783 WThalassa TH1099
888838CTD or STD cast1999-10-18 07:37:0042.674 N, 9.2115 WThalassa TH1099