Metadata Report for BODC Series Reference Number 975558

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

Data Access Policy

Public domain data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

The recommended acknowledgment is

"This study uses data from the data source/organisation/programme, provided by the British Oceanographic Data Centre and funded by the funding body."

Narrative Documents

Neil Brown MK3 CTD

The Neil Brown MK3 conductivity-temperature-depth (CTD) profiler consists of an integral unit containing pressure, temperature and conductivity sensors with an optional dissolved oxygen sensor in a pressure-hardened casing. The most widely used variant in the 1980s and 1990s was the MK3B. An upgrade to this, the MK3C, was developed to meet the requirements of the WOCE project.

The MK3C includes a low hysteresis, titanium strain gauge pressure transducer. The transducer temperature is measured separately, allowing correction for the effects of temperature on pressure measurements. The MK3C conductivity cell features a free flow, internal field design that eliminates ducted pumping and is not affected by external metallic objects such as guard cages and external sensors.

Additional optional sensors include pH and a pressure-temperature fluorometer. The instrument is no longer in production, but is supported (repair and calibration) by General Oceanics.

Specifications

These specification apply to the MK3C version.

Further details can be found in the specification sheet.

SeaTech Transmissometer

Introduction

The transmissometer is designed to accurately measure the the amount of light transmitted by a modulated Light Emitting Diode (LED) through a fixed-length in-situ water column to a synchronous detector.

Specifications

• Water path length: 5 cm (for use in turbid waters) to 1 m (for use in clear ocean waters).
• Beam diameter: 15 mm
• Transmitted beam collimation: <3 milliradians
• Receiver acceptance angle (in water): <18 milliradians
• Light source wavelength: usually (but not exclusively) 660 nm (red light)

Notes

The instrument can be interfaced to Aanderaa RCM7 current meters. This is achieved by fitting the transmissometer in a slot cut into a customized RCM4-type vane.

A red LED (660 nm) is used for general applications looking at water column sediment load. However, green or blue LEDs can be fitted for specilised optics applications. The light source used is identified by the BODC parameter code.

Further details can be found in the manufacturer's Manual.

RRS Charles Darwin 62 CTD Data Documentation

Introduction

CTD profile data are presented from the CONVEX cruise Charles Darwin 62, as reported by Gould et al. (1992).

Instrumentation and Methodology

Instrumentation Summary

The CTD profiles were taken with a Neil Brown Systems MkIIIb CTD mounted beneath a bottle rosette. The CTD was fitted with a pressure sensor, conductivity cell, platinum resistance thermometer, a dissolved oxygen sensor, a Sea Tech 100cm path transmissometer and an IOS 10kHz pinger.

Data Acquisition

Lowering rates for the CTD package were generally in the range 0.5-1.0ms^-1 but could be up to 1.5ms^-1. CTD data were logged at 16 frames per second. The CTD deck unit passes raw data to a dedicated Level A microcomputer where 1 second averages are assembled. During this process the Level A calculates the rate of change of temperature and a median sorting routine detects and removes pressure spikes. These data are sent to the Level B for archival. The data are then passed to a Level C workstation for conversion to Pstar format and calibration.

A total of 96 stations (01 - 96) were occupied, of which 93 used the MkIIIb CTD. A Neil Brown MkV CTD was used at 3 of the stations. Data for stations 79-81 are from full depth casts using this instrument. Two trials had previously been conducted at stations 72 and 76.

Data Processing

The 1 second data passed to the Level C were converted to Pstar format and initially calibrated with coefficients from laboratory calibrations. The up cast data were extracted for merging with the bottle firing codes, on time, thus the CTD variables were reconciled with the bottle samples. Final calibrations were applied using the sample bottle data. The data were worked up to WOCE standards by the data originators before being supplied to BODC.

BODC Data Processing

No further calibrations were applied to the data received by BODC. BODC were mainly concerned with the screening and banking of the data.

The CTD data were received as 2db averaged pressure sorted down cast data. Parameters were pressure (dbar), temperature (°c), salinity (pss-78), oxygen (µmol/kg) and potential attenuance (/m).

The data were converted into the BODC internal format (PXF) to allow the use of in-house software tools, notably the graphics editor. Oxygen was converted to umol/l.

Spikes in the data were manually flagged 'suspect' by modification of the associated quality control flag. In this way none of the original data values were edited or deleted during quality control. These data from cruise CD62 required little flagging and just a few points were set suspect. Profiles 079, 080, and 081 were made using the MkV CTD and have null attenuance.

Once screened, the CTD data were loaded into a database under the Oracle relational database management system. The start time stored in the database is the CTD deployment time, and the end time is the time the CTD was removed from the water. Actually these times are more precisely the start and end of data logging. Latitude and longitude are the mean positions between the start and end times calculated from the master navigation in the binary merged file. The longitude given to the end time for station 62 in the cruise report is incorrect and should be closer to -35 50.0.

Potential attenuance was converted to attenuance from within Oracle as follows:

The following comparison was made between the maximum CTD pressure and bottle firing pressure:

For stations 62019, 62021 and 62042 the tail end of the CTD cast might have been edited out by the originating scientists. For station 62086 there were null entries for CTDPRS, CTDTMP and CTDSAL for bottle 1 (REVPRS = 549.0 dbar) in the bottle data file. For station 62088 there was no entry for bottle 1 in the bottle file.

References

Gould, W.J. et al. (1992). RRS Charles Darwin Cruise 62. Institute of Oceanographic Sciences Deacon Laboratory, Cruise Report No. 230, 60pp.

Project Information

World Ocean Circulation Experiment (WOCE)

The World Ocean Circulation Experiment (WOCE) was a major international experiment which made measurements and undertook modelling studies of the deep oceans in order to provide a much improved understanding of the role of ocean circulation in changing and ameliorating the Earth's climate.

WOCE had two major goals:

• Goal 1. To develop models to predict climate and to collect the data necessary to test them.

• Goal 2. To determine the representativeness of the Goal 1 observations and to deduce cost effective means of determining long-term changes in ocean circulation.

UK WOCE

The UK made a substantial contribution to the international World Ocean Circulation Experiment (WOCE) project by focusing on two important regions:

1. Southern Ocean - links all the worlds oceans, controlling global climate.
2. North Atlantic - directly affects the climate of Europe.

A major part of the UK effort was in the Southern Ocean and work included:

• Two surveys, in the South Atlantic as part of the WOCE Hydrographic Programme.
• SWINDEX, a year long study of the Antarctic Circumpolar Current (ACC) where it crosses major topography south of Africa.
• ADOX, a study of deep water flow from the Atlantic to the Indian Ocean.
• ACCLAIM, a study of the ACC by altimetry and island measurements.

In the North Atlantic the UK undertook:

• NATRE, a purposeful tracer experiment to look at cross isopycnic processes.
• CONVEX, a study of the deep ocean circulation and its changes.
• VIVALDI, a seven year programme of seasonally repeated surveys to study the upper ocean.
• Long-term observations of ocean climate in the North West Approaches.

Satellite ocean surface topography, temperature and wind data were merged with in situ observations and models to create a complete description of ocean circulation, eddy motion and the way the ocean is driven by the atmosphere.

The surveys were forerunners to the international Global Ocean Observing System (GOOS). GOOS was later established to monitor annual to decadal changes in ocean circulation and heat storage which are vital in the prediction of climate change.

Data Activity or Cruise Information

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

World Ocean Circulation Experiment (WOCE) Atlantic Area 12 (AR12)

WOCE was a major international experiment which made measurements and undertook modelling studies of the deep oceans in order to provide a much improved understanding of the role of ocean circulation in changing and ameliorating the Earth's climate. WOCE established numerous areas and repeat sections in the Atlantic Ocean as illustrated in the map below.

AR12 spans the boundary between the subtropical and subpolar gyres in the eastern basin; stations lie within a box bounded by 40.0°N, 35.0°W at the southwest corner and 65.0°N, 03.0°W at the northeast corner The area was occupied between April 1991 to September 1998. A table of all AR12 cruises is presented below:

Related Fixed Station activities are detailed in Appendix 1

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: WOCE Atlantic Area 12 (AR12)

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.