Metadata Report for BODC Series Reference Number 1972558

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

Data Access Policy

Open Data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

If the Information Provider does not provide a specific attribution statement, or if you are using Information from several Information Providers and multiple attributions are not practical in your product or application, you may consider using the following:

"Contains public sector information licensed under the Open Government Licence v1.0."

Narrative Documents

Nortek Aquadopp Open Water Current Meter

This instrument provides 3D acoustic doppler current measurements along with standard measurements of temperature, pressure, tilt and direction. It can be used in real time measurement situations or can log to an internal recorder powered by internal batteries. It can also be configured to measure surface wave height, period and direction concurrently. It has the unique feature of being run in 'diagnostic' mode when set to collect data at 1 Hz frequency in user specified intervals. This allows studies of mooring motion and the performance of other current meters to be conducted. It can be set in various configurations with titanium housings for deployment at greater depths.

Standard Measured Parameters

• 3D current velocity (East/North/Up, X/Y/Z or Beam 1/2/3)

• Acoustic signal strength (Beam 1/2/3)

• Compass

• Tilt

• Temperature

• Pressure

• Battery voltage

• Status code

• Error code

Surface wave monitoring

The standard Aquadopp is suitable for measuring surface wave height, period, and direction, which are calculated using the PUV method whereby spectra are estimated based on a combination of the pressure signal recorded by the instrument (P) and two horizontal components of the wave orbital velocity (U and V). More specifically, the pressure signal is used to provide an estimate of the wave frequency spectrum. The energy in this spectrum is then used to estimate wave height and period. The measurements of the wave orbital velocities are used to provide an estimate of the wave direction. Since these estimates are based on the distribution of wave energy and are not direct measurements of the free surface, they should be considered inferred estimates.

Both the dynamic pressure and the orbital velocities are driven by surface waves. The signals that are associated with these properties are complicated by the fact that they attenuate (that is the signals are weaker) with depth. The exact behaviour of the attenuation is determined by the water depth and the wavelength being observed. The greater the water depth the greater the attenuation; likewise, the shorter the wavelength (or higher the frequency of the wave) the greater the attenuation for a given water depth. This means that the estimation of wave parameters is limited by both water depth and wave frequency.

Specifications

Further details can be found in the manufacturer's specification sheets for the Aquadopp, Aquadopp 3000 and Aquadopp 6000.

RAPIDMOC/MOCHA Current Meter data processing document

This document outlines the procedures undertaken to process and quality assure current meter data collected under the RAPIDMOC and MOCHA projects.

Originator's processing

The raw data are downloaded from the instrument and converted to ASCII format.

Once in ASCII format the data are corrected for the following -

• Speed bias (caused by the mooring motion)
• Sound speed (as electromagnetic current meter sensors use the speed of sound in water to calculate the doppler shift in the returned signal, they are corrected for variations in sound speed using temperature data as sound speed varies with temperature).
• Magnetic variation

A 40 hour low pass filter is also applied to the data.

Calculating and applying calibrations

Manufacturers calibrations are applied.

Quality Control

Data were visually inspected for out-lying data and instrument electrical spikes removed.

BODC processing

Data are received after quality checks have been made and calibrations have been applied. The data files are submitted in ASCII format as one file per instrument.

Once the submitted data files are safely archived, the data undergo reformatting and banking procedures:

• The data files are transferred into a common format, a NetCDF subset.

• Standard parameter codes are assigned that accurately describe the data (see Parameter mapping section below).

• Unit conversions are applied, if necessary, so that units are standardised (see Parameter mapping section below).

• The data are screened visually and any spikes or instrument malfunctions can be clearly labelled with quality control flags.

• Comprehensive documentation is prepared describing the collection, processing and quality of each data series.

• Detailed metadata and documents are loaded to the database and linked to each series so that the information is readily available to future users.

Parameter mapping

The following describes the parameters contained in the originator's files and their mapping to BODC parameter codes:

Project Information

Meridional Overturning Circulation and Heatflux Array (MOCHA) Project

Introduction

Users of these data are referred to the Meridional Overturning Circulation and Heatflux Array (MOCHA) Project Website for more information. The following text has been taken from the website.

Scientific Rationale

To set in place a system for continuous observation of the meridional heat transport in the subtropical Atlantic, with which to document its variability and its relationship to oberved climate fluctuations, and to assess climate model predictions

Overview

MOCHA is a collaborative project, partnered with the UK RAPID Program, to measure the heat and freshwater transports of the North Atlantic Ocean. These transports are called the Thermohaline or Overturning Circulation. Simply put, warm waters move poleward at the surface of the ocean, where they cool and sink, to return equatorward in the deep ocean.

Data Activity or Cruise Information

Data Activity

RAPID Moored Instrument Rig WB3#9

This rig was deployed as part of the Western Boundary (WB) array of the MOCHA/RAPIDMOC project.

The rig was anchored by 5000lbs of railway wheels and kept erect by a 49" syntactic float and groups of small floats distributed along the mooring.

Instruments deployed on the rig

Related Data Activity activities are detailed in Appendix 1

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

RAPIDMOC/MOCHA Western Boundary (WB) Array

The Western Boundary Array defines a box in which moorings were deployed at the western side of the North Atlantic as part of the RAPIDMOC project and the collaborative project Meridional Overturning Circulation and Heatflux Array (MOCHA). The box region has latitudinal limits of 26° N to 27.5° N and longitudinal limits of 69.5° W to 77.5° W. Moorings have occupied this region since 2004 and are typically deployed for 6 to 18 months.

Moored data summary

Cruise data summary

During the cruises to service the moored array, a variety of data types are collected. The table below is a summary of these data. The number of CTD profiles performed on these cruises within the box region defined above is also included. Trans-Atlantic hydrographic CTD sections have also been performed since 2004 and are included in the table.

Data type ID and description

Related Fixed Station activities are detailed in Appendix 2

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: WB3#9

Related series for this Data Activity are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.

Appendix 2: Western Boundary Array

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.