Metadata Report for BODC Series Reference Number 1112792


Metadata Summary

Data Description

Data Category CTD or STD cast
Instrument Type
NameCategories
Sea-Bird SBE 911plus CTD  CTD; water temperature sensor; salinity sensor
Sea-Bird SBE 3plus (SBE 3P) temperature sensor  water temperature sensor
Sea-Bird SBE 4C conductivity sensor  salinity sensor
Instrument Mounting lowered unmanned submersible
Originating Country United Kingdom
Originator Dr Stuart Cunningham
Originating Organization National Oceanography Centre, Southampton
Processing Status banked
Project(s) RAPIDMOC
RAPID-WATCH
 

Data Identifiers

Originator's Identifier CTD_JC064_003_2DB
BODC Series Reference 1112792
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 2011-09-14 21:08
End Time (yyyy-mm-dd hh:mm) -
Nominal Cycle Interval 2.0 decibars
 

Spatial Co-ordinates

Latitude 24.92180 N ( 24° 55.3' N )
Longitude 21.31840 W ( 21° 19.1' W )
Positional Uncertainty 0.01 to 0.05 n.miles
Minimum Sensor Depth 0.99 m
Maximum Sensor Depth 4495.38 m
Minimum Sensor Height 57.22 m
Maximum Sensor Height 4551.61 m
Sea Floor Depth 4552.6 m
Sensor Distribution Variable common depth - All sensors are grouped effectively at the same depth, but this depth varies significantly during the series
Sensor Depth Datum Approximate - Depth is only approximate
Sea Floor Depth Datum Approximate - Depth is only approximate
 

Parameters

BODC CODE Rank Units Short Title Title
ACYCAA01 1 Dimensionless Record_No Sequence number
CNDCST01 1 Siemens per metre CTDCond Electrical conductivity of the water body by CTD
POTMCV01 1 Degrees Celsius WC_Potemp Potential temperature of the water body by computation using UNESCO 1983 algorithm
PRESPR01 1 Decibars Pres_Z Pressure (spatial co-ordinate) exerted by the water body by profiling pressure sensor and corrected to read zero at sea level
PSALCC01 1 Dimensionless P_sal_CTD_calib Practical salinity of the water body by CTD and computation using UNESCO 1983 algorithm and calibration against independent measurements
SIGTPR01 1 Kilograms per cubic metre SigTheta Sigma-theta of the water body by CTD and computation from salinity and potential temperature using UNESCO algorithm
TEMPCU01 1 Degrees Celsius Uncal_CTD_Temp Temperature of the water body by CTD and NO verification against independent measurements
 

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database


Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."


Narrative Documents

RAPID Cruise JC064 CTD instrument description

CTD unit and auxiliary sensors

The CTD configuration comprised a Sea-Bird Electronics 9 plus system #09P-0943, with accompanying Sea-Bird Electronics 11 plus V2 deck unit #11P-24680-0587. The CTD frame was fitted with two Sea-Bird 3 Premium temperature sensors, two Sea-Bird 4 conductivity sensors, a digiquartz temperature compensated pressure sensor, a Sea-Bird 43 dissolved oxygen sensor and a benthos PSA-916T 7Hz altimeter. All instruments (other than cast 012) were attached to a Sea-Bird 24 position carousel #32-19817-0243 containing 12 Ocean Test Equipment 10L water samplers (#1A, 3A, 5A, 7A, 9A, 11A, 13A, 15A, 17A, 19A, 21A and 23A) and were used in alternate positions on the CTD frame. This was to allow moored instruments to be strapped to the frame for calibration purposes. Cast 012 used 24 bottles and therefore included the remaining even numbered samplers (#2A, 4A, 6A, 8A, 10A, 12A, 14A, 16A, 18A, 20A, 22A and 24A). The table below lists more detailed information about the various sensors.

Sensor Unit Model Serial Number Full Specification Last calibration date (YYYY-MM-DD) Comments
CTD underwater unit SBE 9 plus 09P-0943 SBE 9 plus 2009-04-26 -
Temperature sensor SBE 3P 03P-2674 SBE 03P 2011-04-13 Primary sensor
Temperature sensor SBE 3P 03P-4872 SBE 03P 2011-04-19 Secondary sensor
Conductivity sensor SBE 4 04C-2231 SBE 04C 2011-04-12 Primary sensor
Conductivity sensor SBE 4 04C-3258 SBE 04C 2011-04-12 Secondary sensor
Pressure sensor SBE 9 plus digiquartz 110557 - 2009-04-26 -
Dissolved oxygen SBE 43 43-0363 SBE 43 2011-01-26 -
Benthos altimeter PSA-916T 7Hz 41302 - 2007-04-20 -

The salinity samples from the CTD were analysed during the cruise using a Guildline Autosal model 8400B (#68426).

Sea-Bird Electronics SBE 911 and SBE 917 series CTD profilers

The SBE 911 and SBE 917 series of conductivity-temperature-depth (CTD) units are used to collect hydrographic profiles, including temperature, conductivity and pressure as standard. Each profiler consists of an underwater unit and deck unit or SEARAM. Auxiliary sensors, such as fluorometers, dissolved oxygen sensors and transmissometers, and carousel water samplers are commonly added to the underwater unit.

Underwater unit

The CTD underwater unit (SBE 9 or SBE 9 plus ) comprises a protective cage (usually with a carousel water sampler), including a main pressure housing containing power supplies, acquisition electronics, telemetry circuitry, and a suite of modular sensors. The original SBE 9 incorporated Sea-Bird's standard modular SBE 3 temperature sensor and SBE 4 conductivity sensor, and a Paroscientific Digiquartz pressure sensor. The conductivity cell was connected to a pump-fed plastic tubing circuit that could include auxiliary sensors. Each SBE 9 unit was custom built to individual specification. The SBE 9 was replaced in 1997 by an off-the-shelf version, termed the SBE 9 plus , that incorporated the SBE 3 plus (or SBE 3P) temperature sensor, SBE 4C conductivity sensor and a Paroscientific Digiquartz pressure sensor. Sensors could be connected to a pump-fed plastic tubing circuit or stand-alone.

Temperature, conductivity and pressure sensors

The conductivity, temperature, and pressure sensors supplied with Sea-Bird CTD systems have outputs in the form of variable frequencies, which are measured using high-speed parallel counters. The resulting count totals are converted to numeric representations of the original frequencies, which bear a direct relationship to temperature, conductivity or pressure. Sampling frequencies for these sensors are typically set at 24 Hz.

The temperature sensing element is a glass-coated thermistor bead, pressure-protected inside a stainless steel tube, while the conductivity sensing element is a cylindrical, flow-through, borosilicate glass cell with three internal platinum electrodes. Thermistor resistance or conductivity cell resistance, respectively, is the controlling element in an optimized Wien Bridge oscillator circuit, which produces a frequency output that can be converted to a temperature or conductivity reading. These sensors are available with depth ratings of 6800 m (aluminium housing) or 10500 m (titanium housing). The Paroscientific Digiquartz pressure sensor comprises a quartz crystal resonator that responds to pressure-induced stress, and temperature is measured for thermal compensation of the calculated pressure.

Additional sensors

Optional sensors for dissolved oxygen, pH, light transmission, fluorescence and others do not require the very high levels of resolution needed in the primary CTD channels, nor do these sensors generally offer variable frequency outputs. Accordingly, signals from the auxiliary sensors are acquired using a conventional voltage-input multiplexed A/D converter (optional). Some Sea-Bird CTDs use a strain gauge pressure sensor (Senso-Metrics) in which case their pressure output data is in the same form as that from the auxiliary sensors as described above.

Deck unit or SEARAM

Each underwater unit is connected to a power supply and data logging system: the SBE 11 (or SBE 11 plus ) deck unit allows real-time interfacing between the deck and the underwater unit via a conductive wire, while the submersible SBE 17 (or SBE 17 plus ) SEARAM plugs directly into the underwater unit and data are downloaded on recovery of the CTD. The combination of SBE 9 and SBE 17 or SBE 11 are termed SBE 917 or SBE 911, respectively, while the combinations of SBE 9 plus and SBE 17 plus or SBE 11 plus are termed SBE 917 plus or SBE 911 plus .

Specifications

Specifications for the SBE 9 plus underwater unit are listed below:

Parameter Range Initial accuracy Resolution at 24 Hz Response time
Temperature -5 to 35°C 0.001°C 0.0002°C 0.065 sec
Conductivity 0 to 7 S m -1 0.0003 S m -1 0.00004 S m -1 0.065 sec (pumped)
Pressure 0 to full scale (1400, 2000, 4200, 6800 or 10500 m) 0.015% of full scale 0.001% of full scale 0.015 sec

Further details can be found in the manufacturer's specification sheet .

BODC CTD Screening

BODC screen both the series header qualifying information and the parameter values in the data cycles themselves.

Header information is inspected for:

Documents are written by BODC highlighting irregularities that cannot be resolved.

Data cycles are inspected using depth series plots of all parameters. These presentations undergo screening to detect infeasible values within the data cycles themselves and inconsistencies when comparing adjacent data sets displaced with respect to depth, position or time.

Values suspected of being of non-oceanographic origin may be tagged with the BODC flag denoting suspect value.

The following types of irregularity, each relying on visual detection in the time series plot, are amongst those that may be flagged as suspect:

If a large percentage of the data is affected by irregularities, deemed abnormal, then instead of flagging the individual suspect values, a caution may be documented.

The following types of inconsistency are detected automatically by software:

Inconsistencies between the characteristics of the data set and those of its neighbours are sought, and where necessary, documented. This covers inconsistencies in the following:

This screening of the parameter values seeks to confirm the qualifying information and the source laboratory's comments on the series. In screening and collating information, every care is taken to ensure that errors of BODC's making are not introduced.

RAPID Cruise JC064 BODC CTD data processing

The data arrived at BODC in 11 MSTAR format files representing the CTD casts conducted during cruise JC064. The data contained in the files are the downcast data averaged to a 2db pressure grid. The casts were reformatted to BODC's internal NetCDF format. The following table shows the mapping of variables within the MSTAR files to appropriate BODC parameter codes:

Originator's variable Units Description BODC parameter code Units Comments
press dbar Pressure exerted by the water column PRESPR01 dbar Manufacturer's calibration applied.
temp °C Temperature of the water column by CTD (Primary sensor) TEMPCU01 °C ITS-90
temp1 °C Temperature of the water column by CTD (Primary sensor) - - Not transferred. temp and temp1 contain the same data values so only temp was transferred.
temp2 °C Temperature of the water column by CTD (Secondary sensor) TEMPCU02 °C ITS-90. Data from temp were deemed superior by Originator, hence channel not included in final BODC data set.
psal - Practical salinity of the water column (Primary sensor data) PSALCC01 - Calculated by Originator using calibrated conductivity.
psal1 - Practical salinity of the water column (Primary sensor data) - - Not transferred. psal and psal1 contain the same data values so only psal was transferred.
psal2 - Practical salinity of the water column (Secondary sensor data) PSALCU02 - Calculated by Originator using uncalibrated conductivity. Data from psal were deemed superior by Originator, hence channel not included in final BODC data set.
potemp °C Potential temperature of the water column (Primary sensor) POTMCV01 °C Not transferred. Derived by BODC using temp and press.
potemp1 °C Potential temperature of the water column (Primary sensor) - - Not transferred. Contains the same data values as potemp.
potemp2 °C Potential temperature of the water column (Secondary sensor) POTMCV02 °C Not transferred
cond mS/cm Electrical conductivity of the water column (Primary sensor) CNDCST01 S/m /10. Calibrated by Data Originator with discrete salinity samples.
cond1 mS/cm Electrical conductivity of the water column (Primary sensor) - - Not transferred. cond and cond1 contain the same data values so only cond was transferred.
cond2 mS/cm Electrical conductivity of the water column (Secondary sensor) CNDCST02 S/m Data from cond were deemed superior by Originator, hence channel not included in final BODC data set.
depth metres Depth below surface converted from pressure using UNESCO algorithm DEPHPR01 metres Not transferred
altimeter meters Height above bed from CTD - - Not transferred
time seconds Time in seconds since the origin defined in the metadata field data_time_origin - - Not transferred
- - - SIGTPR01 kg/m 3 Derived by BODC using POTMCV01 and PSALCC01

Although there was an oxygen sensor on the CTD frame, no data were received.

The reformatted data were visualised using the in-house EDSERPLO software. Suspect data were marked by adding an appropriate quality control flag, and missing data marked by setting both the data to an appropriate value and setting the quality control flag.

Detailed metadata and documentation were compiled and linked to the data.

RAPID Cruise JC064 Originator's CTD data processing

Sampling strategy

JC064 formed the second leg of the JC064 cruise, while JC063 was referred to as the first. The JC064 cruise began on 10 September 2011 in Santa Cruz de Tenerife. A total of 11 CTD casts were performed during the cruise along approximately 26.5°N, which includes the Eastern boundary, Mid Atlantic Ridge and Western boundary sections of the RAPIDMOC array. Two casts were performed on JC063, therefore making a total of 13 casts executed at 13 different stations. On each cast, up to 12 SBE37 MicroCATs were attached to the frame for calibration purposes. One cast (referenced as cast 012) used 24 water samplers as additional samples of Antarctic Bottom Water were desired, so no MicroCATs were attached. The CTD casts provided start-point calibrations for instruments to be deployed and end-point calibrations for recovered instruments. For recovered instruments that were re-deployed, the post-deployment cast provided a pre-deployment calibration. The instruments were set to the fastest sampling rate and the CTD lowered as normal. On the upcast, the bottle stops were increased to 5 minutes to allow time for stabilisation and the provision of more accurate data. To allow the instruments to be attached to the CTD frame using bespoke attachments, up to 12 sample bottles were removed on all casts (excluding cast 012).

Data processing

Raw CTD data were transferred from the Sea-Bird deck unit to a LINUX machine via Sea-Bird software. The binary files are converted using Sea-Bird processing software (SBE Data Processing v7.20g). Physical units were calculated from the frequency data using the manufacturer's calibration routines and the data converted to ASCII format. The ASCII files were converted to MSTAR format and MEXEC programs run to process the data which included reducing the frequency of the data from 24Hz to 1Hz, calibrating the data, and averaging the downcast to a 2db pressure grid. A calibration was produced for the CTD primary conductivity sensor by merging the salinity sample data with the CTD data. Details of the MEXEC programs used and further details of the processing performed can be found in Cunningham et al. (2012).

Field calibrations

Independent salinity samples, obtained from the bottles on the CTD frame, were used to calibrate the CTD salinity data. Bottle samples with incorrect conductivities were identified and removed from the calibration. Data points were excluded if the residual (bottle conductivities minus CTD conductivities) was outside the limits -0.002 to 0.005 mS/cm. Also if the residual was larger than 3 standard deviations of the new station mean, the data were excluded.

A slope correction to account for sensor drift was applied such that C CTD corrected 1 =C CTD *K. As no distinct groups of casts were identified, all 11 stations were treated as one block in the ctd_cal script where K=1.000027.

A quadratic fit of residual difference against pressure was then applied to remove the increase in residual with depth. The quadratic polynomial computed by ctd_cal was

ΔC = (1.6028 exp -11 ) p 2- (3.6391 exp -07 ) p + 0.0007507.

References

Cunningham, S.A., McCarthy, G., Collins, J. (ed.) (2012) RRS James Cook Cruise JC064 , 10 Sep-09 Oct 2011. RAPID moorings cruise report. Southampton, UK, National Oceanography Centre, Southampton, 183pp. (National Oceanography Centre Cruise Report, No 14)


Project Information

Monitoring the Meridional Overturning Circulation at 26.5N (RAPIDMOC)

Scientific Rationale

There is a northward transport of heat throughout the Atlantic, reaching a maximum of 1.3PW (25% of the global heat flux) around 24.5°N. The heat transport is a balance of the northward flux of a warm Gulf Stream, and a southward flux of cooler thermocline and cold North Atlantic Deep Water that is known as the meridional overturning circulation (MOC). As a consequence of the MOC northwest Europe enjoys a mild climate for its latitude: however abrupt rearrangement of the Atlantic Circulation has been shown in climate models and in palaeoclimate records to be responsible for a cooling of European climate of between 5-10°C. A principal objective of the RAPID programme is the development of a pre-operational prototype system that will continuously observe the strength and structure of the MOC. An initiative has been formed to fulfill this objective and consists of three interlinked projects:

The entire monitoring array system created by the three projects will be recovered and redeployed annually until 2008 under RAPID funding. From 2008 until 2014 the array will continue to be serviced annually under RAPID-WATCH funding.

The array will be focussed on three regions, the Eastern Boundary (EB), the Mid Atlantic Ridge (MAR) and the Western Boundary (WB). The geographical extent of these regions are as follows:

References

Baehr, J., Hirschi, J., Beismann, J.O. and Marotzke, J. (2004) Monitoring the meridional overturning circulation in the North Atlantic: A model-based array design study. Journal of Marine Research, Volume 62, No 3, pp 283-312.

Baringer, M.O'N. and Larsen, J.C. (2001) Sixteen years of Florida Current transport at 27N Geophysical Research Letters, Volume 28, No 16, pp3179-3182

Bryden, H.L., Johns, W.E. and Saunders, P.M. (2005) Deep Western Boundary Current East of Abaco: Mean structure and transport. Journal of Marine Research, Volume 63, No 1, pp 35-57.

Hirschi, J., Baehr, J., Marotzke J., Stark J., Cunningham S.A. and Beismann J.O. (2003) A monitoring design for the Atlantic meridional overturning circulation. Geophysical Research Letters, Volume 30, No 7, article number 1413 (DOI 10.1029/2002GL016776)


RAPID- Will the Atlantic Thermohaline Circulation Halt? (RAPID-WATCH)

RAPID-WATCH (2007-2014) is a continuation programme of the Natural Environment Research Council's (NERC) Rapid Climate Change (RAPID) programme. It aims to deliver a robust and scientifically credible assessment of the risk to the climate of UK and Europe arising from a rapid change in the Atlantic Meridional Overturning Circulation (MOC). The programme will also assess the need for a long-term observing system that could detect major MOC changes, narrow uncertainty in projections of future change, and possibly be the start of an 'early warning' prediction system.

The effort to design a system to continuously monitor the strength and structure of the North Atlantic MOC is being matched by comparative funding from the US National Science Foundation (NSF) for the existing collaborations started during RAPID for the observational arrays.

Scientific Objectives

This work will be carried out in collaboration with the Hadley Centre in the UK and through international partnerships.

Mooring Arrays

The RAPID-WATCH arrays are the existing 26°N MOC observing system array (RAPIDMOC) and the WAVE array that monitors the Deep Western Boundary Current. The data from these arrays will work towards meeting the first scientific objective.

The RAPIDMOC array consists of moorings focused in three geographical regions (sub-arrays) along 26.5° N: Eastern Boundary, Mid-Atlantic Ridge and Western Boundary. The Western Boundary sub-array has moorings managed by both the UK and US scientists. The other sub-arrays are solely led by the UK scientists. The lead PI is Dr Stuart Cunningham of the National Oceanography Centre, Southampton, UK.

The WAVE array consists of one line of moorings off Halifax, Nova Scotia. The line will be serviced in partnership with the Bedford Institute of Oceanography (BIO), Halifax, Canada. The lead PI is Dr Chris Hughes of the Proudman Oceanographic Laboratory, Liverpool, UK.

All arrays will be serviced (recovered and redeployed) either on an annual or biennial basis using Research Vessels from the UK, US and Canada.

Modelling Projects

The second scientific objective will be addressed through numerical modelling studies designed to answer four questions:


Data Activity or Cruise Information

Cruise

Cruise Name JC064
Departure Date 2011-09-10
Arrival Date 2011-10-09
Principal Scientist(s)Stuart A Cunningham (National Oceanography Centre, Southampton)
Ship RRS James Cook

Complete Cruise Metadata Report is available here


Fixed Station Information

Fixed Station Information

Station NameEastern Boundary Array
CategoryOffshore area
Latitude25° 51.60' N
Longitude18° 43.98' W
Water depth below MSL

RAPIDMOC Eastern Boundary (EB) Array

The Eastern Boundary Array defines a box in which moorings are deployed at the eastern side of the North Atlantic as part of the RAPIDMOC project. The box region has latitudinal limits of 23.5° N to 29° N and longitudinal limits of 12° W to 25.5° W. Moorings have occupied this region since 2004 and are typically deployed for 6 to 18 months.

Moored data summary

A description of the data types can be found at the bottom of this document.

Year Cruise ID Number of moorings Data types (number of instruments)
2004 D277, PO319 11 BPR (7), CM (10), MCTD (32)
2005 CD170,CD177 15 ADCP (1), BPR (4), CM (4), MCTD (71), IES (2), MMP (1)
2006 D304, PO343, PO345 24 BPR (6), CM (4), MCTD (78), MMP (1)
2007 D324 13 BPR (3), MCTD (53), IES (2)
2008 D334 14 BPR (3), CM (2), MCTD (44), IES (1)
2009 D344 14 BPR (4), CM (2), MCTD (44)
2011 D359, JC064 22 BPR (12), CM (18), MCTD (80), IES (1)
2012 D382 9 BPR (6), CM (10), MCTD (50)
2014 JC103 9 BPR (6), CM (10), MCTD (50)
2015 DY039 9 BPR (6), CM (9), MCTD (50), MCTDO (5), pCO2 (1), RAS (1), SeapHOx (1)

Cruise data summary

During the cruises to service the moored array, a variety of data types are collected. The table below is a summary of these data. The number of CTD profiles performed on these cruises within the box region defined above is also included. Trans-Atlantic hydrographic CTD sections have also been performed since 2004 and are included in the table.

Cruise ID Cruise description Data types Number of CTD profiles performed within the box region
D277 Initial array deployment MET, NAV, SADCP, SURF -
D279 Hydrographic section CTD, DIS, LADCP, MET, NAV, SADCP, SURF 21
CD170 Array service BATH, CTD, DIS, MET, NAV, SADCP, SURF 4
CD177 Array service BATH, CTD, DIS, MET, NAV, SADCP, SURF 6
D304 Array service CTD, DIS, MET, NAV, SADCP, SURF 8
PO343 Array service CTD, DIS, MET, NAV, SADCP, SURF 5
PO345 Array service CTD, DIS, MET, NAV, SADCP, SURF 4
D324 Array service CTD, DIS, MET, NAV, SADCP, SURF 5
D334 Array service CTD, DIS, MET, NAV, SADCP, SURF 15
D344 Array service CTD, DIS, MET, NAV, SADCP, SURF 5
D346 Hydrographic section CTD, DIS, LADCP, MET, NAV, SADCP, SURF 22
D359 Array service CTD, DIS, MET, NAV, SADCP, SURF 4
JC064 Array service CTD, DIS, MET, NAV, SADCP, SURF 5
D382 Array service CTD, DIS, MET, NAV, SADCP, SURF 5
JC103 Array service CTD, DIS, MET, NAV, SADCP, SURF 11
DY039 Array service CTD, DIS, MET, NAV, SADCP, SURF 6

Data type ID and description

Data type ID Description
ADCP Acoustic Doppler Current Profiler
BATH Bathymetry
BPR Bottom Pressure Recorder
CM Current Meter
CTD Conductivity-Temperature-Depth profiler
DIS Discrete water bottle samples
IES Inverted Echo Sounder
LADCP Lowered Acoustic Doppler Current Profiler
MET Meteorology
MCTD Moored Conductivity-Temperature-Depth sensor
MCTDO Moored Conductivity-Temperature-Depth-Oxygen sensor
MMP McLane Moored Profiler - profiling CTD and current meter
NAV Navigation
pCO2 Moored pCO2 sensor
RAS Remote Access Sampler
SADCP Shipborne Acoustic Doppler Current Profiler
SeapHOx Moored pH-Conductivity-Temperature-Depth-Oxygen sensor
SURF Sea surface data

Other Series linked to this Fixed Station for this cruise - 1112811 1112823 1112835 1112847 1133968 1133981 1133993 1134007 1134019 1134020 1134032 1134044 1134056 1134068 1134081 1134093 1134100 1134112 1134124 1134136 1134148 1134161 1134173 1134185 1134197 1134204 1134216 1134228 1134241 1134253 1134265 1134277 1134289 1134290 1134308 1134321 1134333 1134345 1134357 1134369 1134370 1134382 1134394 1134401 1134413 1196797 1196804 1268091 1268109 1268110 1268122 1268134 1268146

Other Cruises linked to this Fixed Station (with the number of series) - CD170 (52) CD177 (31) D277 (39) D304 (57) D324 (61) D334 (44) D344 (48) D346 (22) D359 (49) D382 (59) JC103 (11) PO343 (10) PO345 (30)


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain