Metadata Report for BODC Series Reference Number 701883

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

No Problem Report Found in the Database

Originator's data processing/quality control comments for RIG#927/SB16+#4736

Data supplied to BODC were accompanied by data quality notes from the originator that detailed observations made when the data were processed and subsequent processing decisions. A summary of these notes is available below.

The originator specified that there was no QC performed on these data, however the data were resubmitted to BODC so BODC recommends using the data with caution.

Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."

Narrative Documents

Coastal Observatory Sea-Bird SBE 16plus SEACAT with Seapoint Turbidity Sensor

Data Originator's Processing

Data were downloaded by the Proudman Oceanographic Laboratory (POL) (since 01 April 2010, the National Oceanography Centre Liverpool (NOCL)) from the instrument logger, and factory calibrations were applied to the temperature and conductivity channels. The instruments are returned to the manufacturer for recalibration approximately every two years. The data were then reformatted by POL/NOCL to a standard ASCII format.

Before the data were supplied to BODC, basic quality control was performed by the Data Originator. The first stage of quality checks involved comparing the data from each instrument with CTD measurements recorded during the deployment and recovery of the mooring. Following the comparison against CTD data secondary checks were performed by comparing the data from each instrument against the data from other sensors attached to that mooring. The Originator has provided BODC with a document containing a full description of the quality control methodology. Depending on the result of the quality checks for each series, one of the following actions was performed by the Originator:

• The data was declared good quality and no corrections were applied.
• Series with consistent offsets, spikes or periods of bad data were edited to correct for these issues. Spikes and periods of unrealistic values were converted to NaN values.
• The series was marked as 'use with caution', if there were problems which the Originator was unable to correct, or it was unclear whether there was a problem with the data.
• If the quality of the data from a series was extremely poor, then the Originator recommended that the data should not be used.

A full description of the results of these quality checks can be found in the relevant Originator's data processing comments document.

Sea-Bird SBE 16plus SEACAT

The SBE 16plus is a high accuracy conductivity and temperature recorder (pressure optional). It is designed for moorings and other long-duration, fixed-site deployments. The SBE 16plus has 6 amplified A/D input channels and conditioned power of 500 ma is avaliable for auxiliary sensors, dissolved oxygen, turbidity, fluorescence, PAR etc.

The SBE 16plus is available with a choice of RS-232 or RS-485 interface.

Sensor specifications

General information

Further information can be found in the instrument manual

Seapoint Turbidity Meter

The Seapoint Turbidity Meter detects light scattered by particles suspended in water, generating an output voltage proportional to turbidity or suspended solids. Range is selected by two digital lines which can be hard wired or microprocessor controlled, thereby choosing the appropriate range and resolution for measurement of extremely clean to very turbid waters. The offset voltage is within 1 mV of zero and requires no adjustment across gains. The optical design confines the sensing volume to within 5 cm of the sensor allowing near-bottom measurements and minimizing errant reflections in restricted spaces.

Sensor specifications, current at August 2006, are given in the table below.

Sensor Specifications

** output is non-linear above 750 FTU.

Further details can be found in the manufacturer's specification sheet.

Processing of Coastal Observatory Sea-Bird 16plus SEACAT with Seapoint Turbidity Sensor data by BODC

The data were provided to BODC in ASCII format, and the series were reformatted into BODC standard internal format using a transfer function. The following table shows how the Originator's variables present in the Seapoint 16plus data were mapped to the appropriate BODC parameter codes.

The reformatted data were visualised using the in-house EDSERPLO software. Suspect data were marked by adding an appropriate quality control flag, missing data by both setting the data to an appropriate value and setting the quality control flag.

General Data Screening carried out by BODC

BODC screen both the series header qualifying information and the parameter values in the data cycles themselves.

Header information is inspected for:

• Irregularities such as unfeasible values
• Inconsistencies between related information, for example:
  • Times for instrument deployment and for start/end of data series
  • Length of record and the number of data cycles/cycle interval
  • Parameters expected and the parameters actually present in the data cycles
• Originator's comments on meter/mooring performance and data quality

Documents are written by BODC highlighting irregularities which cannot be resolved.

Data cycles are inspected using time or depth series plots of all parameters. Currents are additionally inspected using vector scatter plots and time series plots of North and East velocity components. These presentations undergo intrinsic and extrinsic screening to detect infeasible values within the data cycles themselves and inconsistencies as seen when comparing characteristics of adjacent data sets displaced with respect to depth, position or time. Values suspected of being of non-oceanographic origin may be tagged with the BODC flag denoting suspect value; the data values will not be altered.

The following types of irregularity, each relying on visual detection in the plot, are amongst those which may be flagged as suspect:

• Spurious data at the start or end of the record.
• Obvious spikes occurring in periods free from meteorological disturbance.
• A sequence of constant values in consecutive data cycles.

If a large percentage of the data is affected by irregularities then a Problem Report will be written rather than flagging the individual suspect values. Problem Reports are also used to highlight irregularities seen in the graphical data presentations.

Inconsistencies between the characteristics of the data set and those of its neighbours are sought and, where necessary, documented. This covers inconsistencies such as the following:

• Maximum and minimum values of parameters (spikes excluded).
• The occurrence of meteorological events.

This intrinsic and extrinsic screening of the parameter values seeks to confirm the qualifying information and the source laboratory's comments on the series. In screening and collating information, every care is taken to ensure that errors of BODC making are not introduced.

Project Information

Proudman Oceanographic Laboratory Coastal Observatory

The Coastal Observatory was established by Proudman Oceanographic Laboratory as a coastal zone real time observing and monitoring system. The main objective is to understand a coastal sea's response both to natural forcing and to the consequences of human activity. Near real-time measurements will be integrated with coupled models into a pre-operational coastal prediction system whose results will be displayed on the World Wide Web.

The Observatory is expected to grow and evolve as resources and technology allow, all the while building up long time series. A site selection pilot study was carried out in September 2001 and the Observatory became operational in August 2002.

The site is located in Liverpool Bay and is subject to typical coastal sea processes, with strong tides, occasional large storm surges and waves, freshwater input, stable and unstable stratification, high suspended sediment concentration and biogeochemical interaction. Measurements and monitoring will focus on the impacts of storms, variations in river discharge (especially the Mersey), seasonality and blooms in Liverpool Bay.

A variety of methods will be used to obtain measurements, including:

1. Moored instruments for in situ time series of currents, temperature and salinity profiles, and surface waves and meteorology. It is hoped that turbidity and chlorophyll measurements will be made at another site as the Observatory progresses;
2. The Cefas Smartbuoy for surface properties such as nutrients and chlorophyll, starting late 2002;
3. R.V. Prince Madog to carry out spatial surveys and service moorings;
4. Instrumented ferries for near surface temperature, salinity, turbidity, chlorophyll and nutrients. The first route will be Liverpool to Douglas, Isle of Man, starting late 2002;
5. Drifters for surface currents and properties such as temperature and salinity, starting in 2004;
6. Tide gauges, with sensors for meteorology, waves, temperature and salinity, where appropriate;
7. Meteorological data from Bidston Observatory and Hilbre Island, HF radar and tide gauge sites;
8. Shore-based HF radar measuring waves and surface currents out to a range of 50 km, starting in 2003;
9. Satellite data, with infrared for sea surface temperature and visible for chlorophyll and suspended sediment.

The partners currently involved with the project are listed below:

• Proudman Oceanographic Laboratory
• British Oceanographic Data Centre
• UK Meteorological Office
• Centre for Environment, Fisheries and Aquaculture Science
• Environment Agency
• Liverpool University and Port Erin Marine Laboratory
• Bangor University School of Ocean Sciences
• National Oceanography Centre Southampton
• Department of Agriculture and Rural Development in Northern Ireland

A summary of Coastal Observatory cruises to date on R.V. Prince Madog is given in the table below:

Data Activity or Cruise Information

Data Activity

Proudman Oceanographic Laboratory Rig#927

Deployment and Recovery

This rig was deployed as part of the Liverpool Bay Coastal Observatory during R.V. Prince Madog cruise PD18_05. Recovery of the rig took place during R.V. Prince Madog cruise PD21_05.

Rig Description

This rig is a bottom frame comprising of the following instruments 0.5 m above the seabed; Waves Acoustic Doppler Current Profiler (ADCP) and a Sea-Bird 16plus. The frame (D6) was fitted with two Benthos releases (70354 - Rx 13.0 kHz, Tx 12.0 kHz enable C, release D and and one with unknown serial number - Rx 10.5 kHz, Tx 11.0 kHz, enable D, release B) with fizz links and a spooler with 200 m of rope for recovery of the ballast weight.

Related Data Activity activities are detailed in Appendix 1

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

Liverpool Bay Coastal Observatory Site 21

This station is one of 34 stations regularly visited by the Proudman Oceanographic Laboratory (POL) as part of the Liverpool Bay Coastal Observatory. The main activity at this site are CTD profiles (since August 2002) which are taken during each site visit. This station was also the secondary mooring site (also referred to as Site B) for the Coastal Observatory project between April 2005 and March 2010. After March 2010 the moorings were moved to site 20. The station lies within a box of mean water depth 24 m with the following co-ordinates:

The position of this station relative to the other POL Coastal Observatory sites can be seen from the figure below.

Mooring Deployment History

2010

2009

2008

2007

2006

2005

CTD Sampling History

The CTD instrument package for these cruises was a Sea-Bird 911plus, with beam transmissometer, fluorometer, LICOR PAR sensor, LISST-25, and oxygen sensor.

Key

ADCP = Acoustic Doppler Current Profiler
BD = Bacterial degradation experiment
CT = Conductivity and temperature logger
CTD = Conductivity, temperature, depth sensor
FL = Fluorometer
OBS = Optical Backscatter Turbidity meter
Telemetry ADCP = ADCP sending data back to shore in real-time
WMS = Automatic water sampler

Related Fixed Station activities are detailed in Appendix 2

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: POLRIG927

Related series for this Data Activity are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.

Appendix 2: Coastal Observatory Site 21

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.