Metadata Report for BODC Series Reference Number 1796189

• Metadata Summary

• Problem Reports

• Data Access Policy

• Narrative Documents

• Project Information

• Data Activity or Cruise Information

• Fixed Station Information

• BODC Quality Flags

• SeaDataNet Quality Flags

Metadata Summary

Problem Reports

DOXYSU02

Oxygen data have not been calibrated against water sample data. Please use with caution.

RRS James Clark Ross Cruise JR20120327 (JR272A,JR254E,JR257) CTD Data Quality Report

BODC have flagged improbable values for parameters CPHLPR01 and POPTDR01 for series reference 1796245 and 1796325.

AHSFZZ01 channel has been flagged where values are constant or increase with depth. The altimeter only collects good data within 100 m of the seabed and these instances of constant values or increases with depth occur more than 100 m from the seabed.

Data Access Policy

Open Data

These data have no specific confidentiality restrictions for users. However, users must acknowledge data sources as it is not ethical to publish data without proper attribution. Any publication or other output resulting from usage of the data should include an acknowledgment.

If the Information Provider does not provide a specific attribution statement, or if you are using Information from several Information Providers and multiple attributions are not practical in your product or application, you may consider using the following:

"Contains public sector information licensed under the Open Government Licence v1.0."

Narrative Documents

Sea-Bird Dissolved Oxygen Sensor SBE 43 and SBE 43F

The SBE 43 is a dissolved oxygen sensor designed for marine applications. It incorporates a high-performance Clark polarographic membrane with a pump that continuously plumbs water through it, preventing algal growth and the development of anoxic conditions when the sensor is taking measurements.

Two configurations are available: SBE 43 produces a voltage output and can be incorporated with any Sea-Bird CTD that accepts input from a 0-5 volt auxiliary sensor, while the SBE 43F produces a frequency output and can be integrated with an SBE 52-MP (Moored Profiler CTD) or used for OEM applications. The specifications below are common to both.

Specifications

Further details can be found in the manufacturer's specification sheet.

RRS James Clark Ross Cruise JR20120327 (JR272A,JR254E,JR257) CTD Instrumentation

The CTD unit was a Sea-Bird Electronics 911 plus system, consisting of an SBE 11 plus deck unit and a 9 plus underwater unit. The CTD was fitted with an altimeter, PAR sensor, transmissometer, fluorometer and oxygen as auxiliary sensors. All instruments were attached to a 24 position stainless steel Sea-Bird SBE 32 carousel water sampler equipped with 24 12L niskin bottle water samplers. The table below provides a detailed list of CTD instrumentation used.

Sea-Bird Electronics SBE 911 and SBE 917 series CTD profilers

The SBE 911 and SBE 917 series of conductivity-temperature-depth (CTD) units are used to collect hydrographic profiles, including temperature, conductivity and pressure as standard. Each profiler consists of an underwater unit and deck unit or SEARAM. Auxiliary sensors, such as fluorometers, dissolved oxygen sensors and transmissometers, and carousel water samplers are commonly added to the underwater unit.

Underwater unit

The CTD underwater unit (SBE 9 or SBE 9 plus) comprises a protective cage (usually with a carousel water sampler), including a main pressure housing containing power supplies, acquisition electronics, telemetry circuitry, and a suite of modular sensors. The original SBE 9 incorporated Sea-Bird's standard modular SBE 3 temperature sensor and SBE 4 conductivity sensor, and a Paroscientific Digiquartz pressure sensor. The conductivity cell was connected to a pump-fed plastic tubing circuit that could include auxiliary sensors. Each SBE 9 unit was custom built to individual specification. The SBE 9 was replaced in 1997 by an off-the-shelf version, termed the SBE 9 plus, that incorporated the SBE 3 plus (or SBE 3P) temperature sensor, SBE 4C conductivity sensor and a Paroscientific Digiquartz pressure sensor. Sensors could be connected to a pump-fed plastic tubing circuit or stand-alone.

Temperature, conductivity and pressure sensors

The conductivity, temperature, and pressure sensors supplied with Sea-Bird CTD systems have outputs in the form of variable frequencies, which are measured using high-speed parallel counters. The resulting count totals are converted to numeric representations of the original frequencies, which bear a direct relationship to temperature, conductivity or pressure. Sampling frequencies for these sensors are typically set at 24 Hz.

The temperature sensing element is a glass-coated thermistor bead, pressure-protected inside a stainless steel tube, while the conductivity sensing element is a cylindrical, flow-through, borosilicate glass cell with three internal platinum electrodes. Thermistor resistance or conductivity cell resistance, respectively, is the controlling element in an optimized Wien Bridge oscillator circuit, which produces a frequency output that can be converted to a temperature or conductivity reading. These sensors are available with depth ratings of 6800 m (aluminium housing) or 10500 m (titanium housing). The Paroscientific Digiquartz pressure sensor comprises a quartz crystal resonator that responds to pressure-induced stress, and temperature is measured for thermal compensation of the calculated pressure.

Additional sensors

Optional sensors for dissolved oxygen, pH, light transmission, fluorescence and others do not require the very high levels of resolution needed in the primary CTD channels, nor do these sensors generally offer variable frequency outputs. Accordingly, signals from the auxiliary sensors are acquired using a conventional voltage-input multiplexed A/D converter (optional). Some Sea-Bird CTDs use a strain gauge pressure sensor (Senso-Metrics) in which case their pressure output data is in the same form as that from the auxiliary sensors as described above.

Deck unit or SEARAM

Each underwater unit is connected to a power supply and data logging system: the SBE 11 (or SBE 11 plus) deck unit allows real-time interfacing between the deck and the underwater unit via a conductive wire, while the submersible SBE 17 (or SBE 17 plus) SEARAM plugs directly into the underwater unit and data are downloaded on recovery of the CTD. The combination of SBE 9 and SBE 17 or SBE 11 are termed SBE 917 or SBE 911, respectively, while the combinations of SBE 9 plus and SBE 17 plus or SBE 11 plus are termed SBE 917 plus or SBE 911 plus.

Specifications

Specifications for the SBE 9 plus underwater unit are listed below:

Further details can be found in the manufacturer's specification sheet.

Chelsea Technologies Group Aquatracka MKIII fluorometer

The Chelsea Technologies Group Aquatracka MKIII is a logarithmic response fluorometer. Filters are available to enable the instrument to measure chlorophyll, rhodamine, fluorescein and turbidity.

It uses a pulsed (5.5 Hz) xenon light source discharging along two signal paths to eliminate variations in the flashlamp intensity. The reference path measures the intensity of the light source whilst the signal path measures the intensity of the light emitted from the specimen under test. The reference signal and the emitted light signals are then applied to a ratiometric circuit. In this circuit, the ratio of returned signal to reference signal is computed and scaled logarithmically to achieve a wide dynamic range. The logarithmic conversion accuracy is maintained at better than one percent of the reading over the full output range of the instrument.

Two variants of the instrument are available, both manufactured in titanium, capable of operating in depths from shallow water down to 2000 m and 6000 m respectively. The optical characteristics of the instrument in its different detection modes are visible below:

* The wavelengths for the turbidity filters are customer selectable but must be in the range 400 to 700 nm. The same wavelength is used in the excitation path and the emission path.

The instrument measures chlorophyll a, rhodamine and fluorescein with a concentration range of 0.01 µg l^-1 to 100 µg l^-1. The concentration range for turbidity is 0.01 to 100 FTU (other wavelengths are available on request).

The instrument accuracy is ± 0.02 µg l^-1 (or ± 3% of the reading, whichever is greater) for chlorophyll a, rhodamine and fluorescein. The accuracy for turbidity, over a 0 - 10 FTU range, is ± 0.02 FTU (or ± 3% of the reading, whichever is greater).

Further details are available from the Aquatracka MKIII specification sheet.

Biospherical Instruments Log Quantum Cosine Irradiance Sensor QCD-905L

The QCD-905L is a submersible radiometer designed to measure irradiance over Photosynthetically Active Radiation (PAR) wavelengths (400-700 nm). It features a cosine directional response when fully immersed in water.

The sensor is a blue-enhanced high stability silicon photovoltaic detector with dielectric and absorbing glass filter assembly, and produces a logarithmic output. Normal output range is -1 to 6 volts with 1 volt per decade. Typically, the instrument outputs 5 volts for full sunlight and has a minimum output of 0.001% full sunlight, where typical noon solar irradiance is 1.5 to 2 x 10¹⁷ quanta cm^-2 s^-1. The instrument can be calibrated with constants for µE cm^-2 s^-1 or quanta cm^-2 s^-1.

The QCD-905L can be coupled to a fixed range data acquisition system like a CTD (Conductivity-Temperature-Depth) profiler or current meter. It has an aluminium and PET housing, and a depth rating of 7000 m.

Specifications

Further details can be found in the manufacturer's manual.

Tritech Digital Precision Altimeter PA200

This altimeter is a sonar ranging device that gives the height above the sea bed when mounted vertically. When mounted in any other attitude the sensor provides a subsea distance. It can be configured to operate on its own or under control from an external unit and can be supplied with simultaneous analogue and digital outputs, allowing them to interface to PC devices, data loggers, telemetry systems and multiplexers.

These instruments can be supplied with different housings, stainless steel, plastic and aluminum, which will limit the depth rating. There are three models available: the PA200-20S, PA200-10L and the PA500-6S, whose transducer options differ slightly.

Specifications

Common specifications are presented below

Further details can be found in the manufacturer's specification sheet.

WETLabs C-Star transmissometer

This instrument is designed to measure beam transmittance by submersion or with an optional flow tube for pumped applications. It can be used in profiles, moorings or as part of an underway system.

Two models are available, a 25 cm pathlength, which can be built in aluminum or co-polymer, and a 10 cm pathlength with a plastic housing. Both have an analog output, but a digital model is also available.

This instrument has been updated to provide a high resolution RS232 data output, while maintaining the same design and characteristics.

Specifications

Further details are available in the manufacturer's specification sheet or user guide.

RRS James Clark Ross Cruise JR20120327 (JR272A,JR254E,JR257) CTD BODC Processing

The processed CTD files were submitted as mstar .nc files. The file contained data for the following parameters: pressure; temperature; conductivity; oxygen; transmittance; fluorescence; PAR; salinity; temperature; and density. Additional deployment metadata such as time, latitude and longitude were also included in the files. The final processed mstar files were reformatted by transferring only relevant parameters and mapping to standardised BODC Parameter codes into an internal NetCDF file.

The following table shows the mapping of the originator variables to the appropriate BODC parameter codes:

Screening

As part of standard BODC procedure, derived parameters submitted by the originator are not transferred due to the uncertainty of the calculations used. BODC re-derives these parameters using standard algorithms.

Screening of data files was then completed using in-house software EDSERPLO, which allows for a visual inspection and flagging of any missing or obvious spikes and improbable values in the data.

Please note the original data submitted to BODC can be made available on request.

RRS James Clark Ross Cruise JR20120327 (JR272A,JR254E,JR257) CTD Originator Processing

Originator's Sampling

A Conductivity-Temperature-Depth (CTD) unit was used to vertically profile the water column. 38 casts were carried out in total, as part of a repeat CTD transect A23 from the Weddell Sea towards South Georgia, at the deployment of a mooring, at gravity coring stations and as a survey of Cumberland Bay.

CTD data were collected at 24Hz and logged via the deck unit to a PC running Seasave, version 7.21d (Sea-Bird Electronics, Inc.), which allows real-time viewing of the data. The procedure was to start data logging, deploy the CTD, then stop the instrument at 10m wireout, where the CTD package was left for at least two minutes to allow the seawateractivated pumps to switch on and the sensors to equilibrate with ambient conditions. The pumps are typically expected to switch on 60 seconds after the instrument is deployed. After the 10m soak, the CTD was raised to as close to the surface as wave and swell condition allowed and then lowered to within 10m of the seabed. Bottles were fired on the upcast, where the procedure was to stop the CTD winch, hold the package in situ for a few seconds to allow sensors to equilibrate, and then fire a bottle. The sensor averages these readings to produce one value for each bottle fire. Short times between firing pairs of bottles sometimes led to no SBE35 readings for the second bottle of the pair.

Salinity samples were taken from the mixed layer and other depths with low vertical salinity gradient to calibrate the CTD conductivity and salinity.

Originator's Processing

Preliminary Processing

The CTD data were recorded using Seasave, version 7.21d, which created four files (NNN is the CTD event number):

• jr272_[NNN].hex binary data file
• jr272_[NNN].XMLCON ascii configuration file with calibration information
• jr272_[NNN].hdr ascii header file containing sensor information
• jr272_[NNN].bl ascii file containing bottle fire information

The .hex file was then converted from binary to ascii using the SBE Data Processing software Data Conversion module. The output was a file named jr272ctd[NNN].cnv.

The data conversion module calculates parameers using coefficients listed on page 10 of the cruise report.

SBE Data Processing Cell thermal mass module was then used to remove the conductivity cell thermal mass effects from the measured conductivity. This reads in the jr272ctd[NNN].cnv file and re-derives the pressure and conductivity, taking into account the temperature of the pressure sensor and the action of pressure on the conductivity cell. The output is another ascii file, named as jr272ctd[NNN]_ctm.cnv.

SBE 35 High Precision Thermometer

Data from the SBE35 thermometer were usually uploaded after every cast using the SeaTerm program. Once the readings had been written to an ascii file (named jr272sbeNNN.asc), the file was opened and the contents checked to make sure the correct number of readings had been stored. The memory of the SBE35 was then cleared. Once all data had been downloaded and the preliminary processing described above carried out, the directory containing all data for that CTD cast was copied to the Unix system for further processing in mstar.

Salinity Samples

At each CTD station 24 niskin bottles were closed at up 11 distinct depths. Up to ten salinity samples were taken (thermocline samples were also taken for organic geochemistry but these were from depths with significant salinity gradient). Sampling, storage and analytical procedures were as per those described in Section 6.4 (Underway). Once analysed, the conductivity ratios were entered by hand into jr272_master.xls, converted to salinities and used for further CTD data processing.

Further Mstar Processing

CTD data were processed using mstar scripts written by Brian King, National Oceanography Centre Southampton. Further in-depth details of the processing applied are listed on page 13 of the cruise report.

CTD Calibration

Details of CTD calibration can be found on page 15 of the cruise report.

Project Information

BAS Long Term Monitoring and Survey

Introduction

The Long Term Monitoring and Survey project (LTMS) has been running since the British Antarctic Survey (BAS) was created. This project is one of the BAS core projects, with several groups of scientists collecting various types of data e.g biological, geological, atmospheric, among others.

Data collection is achievable through a wide scope of instruments and platforms, e.g. the Antarctic research stations, autonomous instrument platforms deployed on or from BAS research ships, BAS aircrafts, satellite remote sensing and others.

Scientific Objectives

This project was implemented in order to measure change and variability in the Earth system. Its long term duration allows for the monitoring of processes that could be missed in shorter term studies and experiments. The data collected is also used to check and improve the reliability of models used to stimulate and predict the behavior of the Earth system.

The main objectives are:

• Topographic survey
• Geosciences survey
• Biological survey and monitoring
• Atmospheric and oceanographic monitoring

Data Availability

The data sets obtained through this project are available to the academic community.

Data Activity or Cruise Information

Cruise

Complete Cruise Metadata Report is available here

Fixed Station Information

Fixed Station Information

WOCE Hydrographic Programme Section A23

This section is part of the One-Time Survey of World Ocean Circulation Experiment (WOCE) designated A23. A hydrographic section from Antarctica to Brazil in the South West Atlantica. A full suite of physical, chemical, biological, meterological and tracer measurements were made. During WOCE in 1995 (James Clark Ross, cruise JR10) the A23 section area encompassed 20-70° S and 20-70° S. Part of this A23 section located in the eastern Scotia Sea has been repeated by theALBATROSS project (James Clark Ross, cruise JR40) in 1999, theUS CLIVAR repeat hydrography/CO₂ in 2005 (R/V Ronald H. Brown, cruise A16S_2005a) under theCLIVAR/Carbon repeat hydrography program. From 2010 onwards the British Antarctic Survey has conducted annual cruises to survey the southern portion of this section, from the Weddell Sea to South Georgia. A comprehensive list of cruises is included below the map.

From

History of Occupations at Section A23

Related Fixed Station activities are detailed in Appendix 1

BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Appendix 1: WOCE section A23

Related series for this Fixed Station are presented in the table below. Further information can be found by following the appropriate links.

If you are interested in these series, please be aware we offer a multiple file download service. Should your credentials be insufficient for automatic download, the service also offers a referral to our Enquiries Officer who may be able to negotiate access.