Metadata Report for BODC Series Reference Number 747162


Metadata Summary

Data Description

Data Category Fluorescence or pigments
Instrument Type
NameCategories
Seapoint chlorophyll fluorometer  fluorometers
Instrument Mounting moored surface buoy
Originating Country United Kingdom
Originator -
Originating Organization Centre for Environment, Fisheries and Aquaculture Science Lowestoft Laboratory
Processing Status banked
Project(s) Coastal Observatory
 

Data Identifiers

Originator's Identifier LB_38_FL2245
BODC Series Reference 747162
 

Time Co-ordinates(UT)

Start Time (yyyy-mm-dd hh:mm) 2006-12-15 10:00
End Time (yyyy-mm-dd hh:mm) 2007-01-27 23:30
Nominal Cycle Interval 1800.0 seconds
 

Spatial Co-ordinates

Latitude 53.53320 N ( 53° 32.0' N )
Longitude 3.36070 W ( 3° 21.6' W )
Positional Uncertainty 0.1 to 0.5 n.miles
Minimum Sensor Depth 1.0 m
Maximum Sensor Depth 1.0 m
Minimum Sensor Height 23.4 m
Maximum Sensor Height 23.4 m
Sea Floor Depth 24.4 m
Sensor Distribution Fixed common depth - All sensors are grouped effectively at the same depth which is effectively fixed for the duration of the series
Sensor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
Sea Floor Depth Datum Instantaneous - Depth measured below water line or instantaneous water body surface
 

Parameters

BODC CODE Rank Units Short Title Title
AADYAA01 1 Days Date(Loch_Day) Date (time from 00:00 01/01/1760 to 00:00 UT on day)
AAFDZZ01 1 Days Time(Day_Fract) Time (time between 00:00 UT and timestamp)
ACYCAA01 1 Dimensionless Record_No Sequence number
CPHLPS01 1 Milligrams per cubic metre chl-a_water_ISfluor_sampcal Concentration of chlorophyll-a {chl-a CAS 479-61-8} per unit volume of the water body [particulate >unknown phase] by in-situ chlorophyll fluorometer and calibration against sample data
FVLTWS01 1 Volts WsVolt Instrument output (voltage) by linear-response chlorophyll fluorometer
 

Definition of Rank

  • Rank 1 is a one-dimensional parameter
  • Rank 2 is a two-dimensional parameter
  • Rank 0 is a one-dimensional parameter describing the second dimension of a two-dimensional parameter (e.g. bin depths for moored ADCP data)

Problem Reports

No Problem Report Found in the Database

SmartBuoy deployment LB_038/985 Fluorometer sensor 2245 Data Quality Report

Fluorescence

There is an offset of 0.2 between the initial values of this deployment and the end values from the previous deployment.


Data Access Policy

Open Data supplied by Natural Environment Research Council (NERC)

You must always use the following attribution statement to acknowledge the source of the information: "Contains data supplied by Natural Environment Research Council."


Narrative Documents

Seapoint Chlorophyll Fluorometer

The Seapoint Chlorophyll Fluorometer (SCF) is a low power instrument for in situ measurements of chlorophyll a. The SCF uses modulated blue LED lamps and a blue excitation filter to excite chlorophyll a. The fluorescent light emitted by the chlorophyll a passes through a red emission filter and is detected by a silicon photodiode. The low level signal is then processed using synchronous demodulation circuitry which generates an output voltage proportional to chlorophyll a concentration. The SCF may be operated with or without a pump.

Sensor specifications, current at August 2006, are given in the table below. More information can be found at the manufacturer's web site .

Sensor Specifications

Power requirements 8 - 20 VDC, 15 mA avg., 27 mA pk.
Output 0 - 5.0 VDC
Output Time Constant 0.1 sec.
Power-up transient period < 1 sec.
Excitation Wavelength 470 nm CWL, 30 nm FWHM
Emission Wavelength 685 nm CWL, 30 nm FWHM
Sensing Volume 340 mm 3
Minimum Detectable Level 0.02 µg l -1

  Gain Sensitivity, V µg -1 l -1 Range, µg l -1
Sensitivity/Range 30x
10x
3x
1x
1.0
0.33
0.1
0.033
5
15
50
150

Cefas SmartBuoy data processing

This document outlines the procedures in place at Cefas in August 2005 for processing and quality assuring SmartBuoy data.

Raw data files are processed and the data move through 4 levels, starting with raw data at level 0 through to level 3, where data are fully quality-assured and expressed in appropriate units. The application of the procedures at each level result in data deemed fit to progress to the next level.

Cefas Quality Assurance (QA) Protocols

At Level 0, raw binary data files from the loggers are transferred to the network.

Automated checks - Level 1

Level 1 involves applying automated quality assurance procedures to the data. These include the following steps:

The data are now at QA status = 1.

Manual checks - Level 2

Level 1 burst mean data are now ready for manual QA procedures in order to progress to Level 2. Deployment notes are consulted for any comments on sensor performance or malfunction and post-deployment photographs of sensors, if available, are examined.

Cefas use a data visualisation tool to examine the SmartBuoy data.

Calibrations - Level 3

The combined information from Level 2 is used to determine the periods during which the data series are considered suspect. The data have now reached QA status = 2 and can progress to Level 3, where they will be fully calibrated with field-derived sample data.

The data have now reached QA status = 3 as time stamped, field calibrated burst mean data with parameter codes and units stored on SmartBuoy database with associated uncertainty or 95% confidence limits as appropriate. All SmartBuoy data banked at BODC have passed full Cefas QA procedures. Data that fail the Cefas QA checks are not submitted for banking.

SmartBuoy data processing by BODC

The following outlines the procedures that take place at BODC for banking Cefas SmartBuoy data.

BODC receives SmartBuoy data from Cefas after all quality checks have been passed and all possible calibrations applied. The data files are submitted as separate MS Excel spreadsheets for each parameter, i.e. there are separate files for temperature and salinity from the same instrument. An exact copy of the data is archived for safekeeping upon arrival.

Once the submitted data files are safely archived, the data undergo standard reformatting and banking procedures:


Project Information

Proudman Oceanographic Laboratory Coastal Observatory

The Coastal Observatory was established by Proudman Oceanographic Laboratory as a coastal zone real time observing and monitoring system. The main objective is to understand a coastal sea's response both to natural forcing and to the consequences of human activity. Near real-time measurements will be integrated with coupled models into a pre-operational coastal prediction system whose results will be displayed on the World Wide Web.

The Observatory is expected to grow and evolve as resources and technology allow, all the while building up long time series. A site selection pilot study was carried out in September 2001 and the Observatory became operational in August 2002.

The site is located in Liverpool Bay and is subject to typical coastal sea processes, with strong tides, occasional large storm surges and waves, freshwater input, stable and unstable stratification, high suspended sediment concentration and biogeochemical interaction. Measurements and monitoring will focus on the impacts of storms, variations in river discharge (especially the Mersey), seasonality and blooms in Liverpool Bay.

A variety of methods will be used to obtain measurements, including:

  1. Moored instruments for in situ time series of currents, temperature and salinity profiles, and surface waves and meteorology. It is hoped that turbidity and chlorophyll measurements will be made at another site as the Observatory progresses;
  2. The Cefas Smartbuoy for surface properties such as nutrients and chlorophyll, starting late 2002;
  3. R.V. Prince Madog to carry out spatial surveys and service moorings;
  4. Instrumented ferries for near surface temperature, salinity, turbidity, chlorophyll and nutrients. The first route will be Liverpool to Douglas, Isle of Man, starting late 2002;
  5. Drifters for surface currents and properties such as temperature and salinity, starting in 2004;
  6. Tide gauges, with sensors for meteorology, waves, temperature and salinity, where appropriate;
  7. Meteorological data from Bidston Observatory and Hilbre Island, HF radar and tide gauge sites;
  8. Shore-based HF radar measuring waves and surface currents out to a range of 50 km, starting in 2003;
  9. Satellite data, with infrared for sea surface temperature and visible for chlorophyll and suspended sediment.

The partners currently involved with the project are listed below:

A summary of Coastal Observatory cruises to date on R.V. Prince Madog is given in the table below:

Year No. of cruises Work summary
2001 1 Site selection and pilot study. 95 CTD casts.
2002 4 POL moorings deployed and serviced
Cefas Waverider and SmartBuoy deployed and serviced
103 CTD casts
2003 10 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
341 CTD/LISST casts
2004 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
347 CTD/LISST casts
2005 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
268 CTD/LISST casts
2006 11 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
508 CTD/LISST casts
2007 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
471 CTD/LISST casts
2008 9 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
260 CTD/LISST casts
2009 7 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
213 CTD/LISST casts
2010 8 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
268 CTD/LISST casts
2011 6 POL moorings serviced
Cefas Waverider and SmartBuoy serviced
307 CTD/LISST casts to date, ongoing

Data Activity or Cruise Information

Data Activity

Start Date (yyyy-mm-dd) 2006-12-15
End Date (yyyy-mm-dd) 2007-02-14
Organization Undertaking ActivityCentre for Environment, Fisheries and Aquaculture Science Lowestoft Laboratory
Country of OrganizationUnited Kingdom
Originator's Data Activity IdentifierLB1_38/985
Platform Categorymoored surface buoy

Smartbuoy deployment LB_038/POLRIG985

Deployment and Recovery

This rig was deployed as part of the Liverpool Bay Coastal Observatory during R.V. Prince Madog cruise PD37_06. The weather was stormy throughout the cruise (force 7 - 9), however, the moorings work was successfully achieved. Recovery of the rig took place during R.V. Prince Madog cruise PD02_07.

Rig Position 53 31.993N, 3 21.643W
Water Depth 24.4m
Deployed 15 December 2006 09:39
Recovered 14 Febuary 2007 13:19
No. of days 61

Rig Description

This rig is a single line mooring, comprising a surface CEFAS SmartBuoy and POL instrumentation suspended beneath. The single point mooring was mainly composed of 0.5 inch long link chain and marked at the surface by a 1.8 m diameter toroid (the CEFAS SmartBuoy) and anchored by a half tonne clump of scrap chain. The CEFAS Smartbuoy contains a suite of instruments mounted just below the surface.

The table below details the CEFAS instrumentation

Instrument Serial
Number
Parameters Meter
depth (m)
Record
Length (days)
Seapoint Fluorometer 2245 Fluorescence
Chlorophyll
1 43
Falmouth Scientific OEM CT sensor 1821 Temperature
Salinity
1 61
Seapoint Turbidity meter 1433 Turbidity
Suspended Load
1 61
LI-COR-192 Underwater Quantum sensor 20 PAR
Vertical Light attenuation coefficient
1 61
LI-COR-192 Underwater Quantum sensor 8 PAR 2 61
EnviroTech WMS-2 Aqua Monitor water sampler 2326 Silicate
Total Oxidised Nitrogen
1 52
EnviroTech NAS in situ nutrient analyser 2273 Total Oxidised Nitrogen 1 61
Aanderaa Oxygen Optode 127 Oxygen Concentration
Oxygen Saturation
1 61

The table below details the POL instrumentation

Instrument Serial Number Meter Level Parameters Measured Sampling Interval Comments
Sea-Bird MicroCAT SBE37-SM 485 V2.2 2991 5 m below surface Temperature
Conductivity
10 minutes Upon recovery the clock was found to be running 30 s fast.
Sea-Bird MicroCAT SBE37-IM V2.1 4998 10 m below surface Temperature
Conductivity
10 minutes -

Other Series linked to this Data Activity - 747499 747057 747334 747451 747395 752951 747266 747506 753026

Cruise

Cruise Name PD37/06
Departure Date 2006-12-14
Arrival Date 2006-12-15
Principal Scientist(s)Phil J Knight (Proudman Oceanographic Laboratory)
Ship RV Prince Madog

Complete Cruise Metadata Report is available here


Fixed Station Information

Fixed Station Information

Station NameCOA
CategoryOffshore area
Latitude53° 31.51' N
Longitude3° 23.00' W
Water depth below MSL26.0 m

Liverpool Bay Coastal Observatory Mooring Site A (COA/Site 1/Site 9)

This station is the main mooring site for the Proudman Oceanographic Laboratory (POL) Liverpool Bay Coastal Observatory and was first occupied in 2002. It is also known both as Coastal Observatory Site 1 and Site 9. POL perform two main types of activities at this station: they deploy moorings; and in addition, they take CTD profiles during each site visit. The station lies within a box of mean water depth 22.5 m with the following coordinates:

Box Corner Latitude (+ve North) Longitude (+ve East)
North-west corner 53.54097 -3.42958
South-east corner 53.50945 -3.33714

The position of this station relative to the other POL Coastal Observatory sites can be seen from the figure below.

BODC image

Mooring Deployment History

2011

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, OBS, OXY 1117, 1121, 1125, 1127, 1130, 1132, January - November
SmartBuoy CTD x 2, AC-S, CT x 2, FL x 3, OBS x 2, PAR x 2, WMS, NAS, OXY, T x 2 1116, 1120, 1124 January - November

2010

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 1086, 1090, 1094, 1098, 1102, 1106, 1109 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T 1085, 1089, 1093, 1097, 1101, 1105, 1108, 1112 January - December

2009

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 1055, 1062, 1067, 1071, 1074, 1078, 1082 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T 1054, 1061, 1066, 1070, 1073, 1077, 1081 January - December

2008

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 1024, 1028, 1032, 1036, 1041, 1044, 1047, 1051 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T LB1_047/1023, LB1_048/1027, LB1_049/1031, LB1_050/1035, 1040, 1043, LB1_053/1050 January - December

2007

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 990, 997, 1001, 1005, 1010, 1014, 1017, 1021 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD, T LB1_039/989, LB1_040/996, LB1_041/1000, LB1_042/1004, LB1_043/1009, LB1_044/1013, LB1_045/1016, LB1_046/1020 January - December

2006

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CTD, ADV, OBS 951, 962, 966, 970, 974, 978, 982, 986 January - December
SmartBuoy CT x 2, FL x 2, OBS, PAR x 2, WMS, NAS, CTD, OXY, BD 958, 961, 965, 969, 973, 977, LB1_037/981, LB1_038/985 January - December

2005

Rig Type Typical Instruments Rig IDs Comment
Frame ADCP, CT 913, 914, 921, 925, 929, 933, 938, 942, 945, 949 January - December
SmartBuoy CT, FL, OBS, PAR, WMS, NAS, OXY 912, 920, 924, 928, 932, 937, LB1_028/941, LB1_029/944, LB1_030/948 January - December
Frame with telemetry buoy ADCP 914 March - April

2004

Rig Type Typical Instruments Rig IDs Comment
Frame BPR, ADCP, TR, CT 890, 892, 893, 896, 898, 900, 902, 904, 907, 908, 910, 911 January - December
SmartBuoy CT, FL, OBS, PAR, WMS, NAS 889, 891, 895, 897, 899, 901, 903, 906, 909 January - December
Frame with telemetry buoy ADCP 893, 908, 911 April - May, October - December

2003

Rig Type Instruments Rig IDs Comment
Frame BPR, ADCP, TR, CT 861, 864, 866, 869, 872, 878, 880, 883, 885, 887, 888 January - December
SmartBuoy CT, FL, OBS, PAR, WMS, NAS 863, 865, 867, 870, 871, 877, 879, 882, 884, 886 January - December

2002

Rig Type Instruments Rig IDs Comment
Frame BPR, ADCP, TR, CT 851, 854, 856, 858 August - December
Line mooring CT x 3 853, 855 August - November
SmartBuoy CT, FL, OBS, PAR, WMS, NAS 857, 860 November - December

2001

Rig Type Instruments Rig IDs Comment
Frame ADCP, OBS 838, 839, 840, 841, 843, 844, 845, 846, 848, 849 September

CTD Sampling History

Year Number of Cruises Total Casts per year
2011 6 116 including a 46 cast tidal cycle from 2011-04-18 to 2011-04-19 and a 51 cast tidal cycle station from 2011-07-27 to 2011-07-28
2010 8 71 including a 52 cast tidal cycle station from 2010-04-28 to 2010-04-29
2009 7 21
2008 9 75 including a 54 cast tidal cycle station from 2008-05-13 to 2008-05-14
2007 8 71 including a 51 cast tidal cycle station from 2007-05-15 to 2007-05-16
2006 9 72 including a 53 cast tidal cycle station from 2006-05-09 to 2006-05-10
2005 9 41 including a 22 cast tidal cycle station from 2005-04-05 to 2005-04-06
2004 9 77 including a 54 cast tidal cycle station from 2004-05-11 to 2004-05-12
2003 10 28
2002 4 13

The CTD instrument package for these cruises was a Sea-Bird 911plus, with beam transmissometer, fluorometer, LICOR PAR sensor, LISST-25, and oxygen sensor.

Key

AC-S = Absorption and attenuation spectrophotometer
ADCP = Acoustic Doppler Current Profiler
ADV = Acoustic Doppler Velocimeter
BD = Bacterial degradation experiment
BPR = Bottom Pressure Recorder
CT = Conductivity and temperature logger
CTD = Conductivity, temperature, depth sensor
FL = Fluorometer
NAS = in-situ nutrient analyser
OBS = Optical Backscatter Turbidity meter
OXY = Oxygen sensor
PAR = PAR sensor
T = Temperature logger
TR = Transmissometer
WMS = Automatic water sampler

Other Series linked to this Fixed Station for this cruise - 747057 747266 747334 747395 747451 747499 747506 752951 753026 753118 1003634 1003646 1623408

Other Cruises linked to this Fixed Station (with the number of series) - CO 01/12 (5) PD01/08 (17) PD01/11 (14) PD02/03 (10) PD02/05 (11) PD02/07 (15) PD02/09B (17) PD02/10 (15) PD04/06 (1) PD05/10 (16) PD06/04 (12) PD06/07 (16) PD07/08 (14) PD07/11 (17) PD09/06 (11) PD09/07 (64) PD09/08 (16) PD10/03 (9) PD10/10 (14) PD11/04B (13) PD11/05 (9) PD11/11 (57) PD12/05 (2) PD12/09 (16) PD13/07 (14) PD14/08 (67) PD16/06 (9) PD16/07 (15) PD17/03 (12) PD17/10 (15) PD18/04 (13) PD18/05 (11) PD18/09 (17) PD19/08 (2) PD20/02 (7) PD20/06 (9) PD20/07 (17) PD21/05 (10) PD21/10 (15) PD21/11 (9) PD22/04 (13) PD22/06 (9) PD23/03A (10) PD23/07 (15) PD23/08 (13) PD24/02 (2) PD24/09 (17) PD25/03B (12) PD25/05 (11) PD25/06 (9) PD25/11 (7) PD27/07 (17) PD29/04 (12) PD29/06 (9) PD29/08 (14) PD29/10 (17) PD30/05 (10) PD31/02 (11) PD31/03 (12) PD32/04 (12) PD33/08 (5) PD33/09 (16) PD34/03 (12) PD34/05 (10) PD35/02 (11) PD35/06 (14) PD36/10 (16) PD37/08 (18) PD38/03 (13) PD38/04 (12) PD38/09 (16) PD41/05 (11) PD43/11 (11) PD44/03 (7) PD47/09 (15) PD48/03 (5) PD48/04 (8) PD48/05 (10) PD49/10 (14) PD52/04 (8)


BODC Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
Blank Unqualified
< Below detection limit
> In excess of quoted value
A Taxonomic flag for affinis (aff.)
B Beginning of CTD Down/Up Cast
C Taxonomic flag for confer (cf.)
D Thermometric depth
E End of CTD Down/Up Cast
G Non-taxonomic biological characteristic uncertainty
H Extrapolated value
I Taxonomic flag for single species (sp.)
K Improbable value - unknown quality control source
L Improbable value - originator's quality control
M Improbable value - BODC quality control
N Null value
O Improbable value - user quality control
P Trace/calm
Q Indeterminate
R Replacement value
S Estimated value
T Interpolated value
U Uncalibrated
W Control value
X Excessive difference

SeaDataNet Quality Control Flags

The following single character qualifying flags may be associated with one or more individual parameters with a data cycle:

Flag Description
0 no quality control
1 good value
2 probably good value
3 probably bad value
4 bad value
5 changed value
6 value below detection
7 value in excess
8 interpolated value
9 missing value
A value phenomenon uncertain